U1 vs IC1 Comparison

flux

Comparison of U1 vs IC1

Table

CategoryU1IC1Main difference
PartU1IC1Different vendors: NXP vs TI
FunctionLIN transceiverLIN transceiverSame basic role
LIN standard supportLIN 2.x / ISO 17987-4:2016 / SAE J2602LIN 2.0 / 2.1 / 2.2 / 2.2A / ISO 17987-4 / SAE J2602-1Very similar compliance; IC1 explicitly lists more LIN revisions
Automotive qualificationNot explicitly called out in the extracted sectionAEC-Q100 Grade 1, Functional Safety-CapableIC1 is more explicitly automotive-qualified
Operating supply voltage5.5 V to 27 V on VBAT4.5 V to 36 V on VSUPIC1 has a much wider operating supply range
Absolute max supply voltage-0.3 V to +40 V-0.3 V to +45 VIC1 tolerates higher supply stress
Recommended LIN bus voltageStatic characteristics given for VBAT 5.5 V to 27 V0 V to 36 VIC1 supports wider bus operating voltage
Absolute max LIN bus voltage-40 V to +40 V-45 V to +45 VIC1 is more fault-tolerant on LIN
Load dump / fault toleranceISO 7637 transient protection, short-circuit proof to battery and groundExplicit 42 V load dump support, ±45 V LIN fault tolerantIC1 is stronger on published fault tolerance
Logic input compatibilityCompatible with 3.3 V and 5 V devicesLogic pins specified for 0 V to 5.25 VU1 explicitly calls out 3.3 V compatibility; IC1 gives tighter logic-voltage limits
RXD outputOpen-drain, 1.5 mA min low-level sinkOpen-drain, 1.5 mA low-level sink, 0.6 V max low levelSimilar drive capability
INH output current-50 mA to +15 mA absolute max4 mA absolute maxU1 can drive a much heavier INH load
INH behaviorSwitch resistance VBAT-to-INH: 20 typ / 50 max ohmsINH high-level drop vs VSUP: 0.5 V to 1 V at -0.5 mADifferent output characterization; U1 looks more suitable for stronger regulator-enable sourcing
Sleep current2 typ / 7 typ? / 10 max uA listed as 2 / 7 / 10 uA depending on min/typ/maxINH leakage in sleep -0.5 to 0.5 uA; full sleep supply current not in extracted sectionU1 has more complete low-power current data in the extracted content
Standby current150 / 450 / 1000 uA recessiveNot captured in extracted sectionU1 gives clearer standby current numbers here
Normal-mode supply current300 / 800 / 1600 uA recessive, 1 / 2 / 4 mA dominantNot captured in extracted sectionU1 has more extracted current-consumption detail
TXD logic thresholdsVIH 2 V to 7 V, VIL -0.3 V to 0.8 V, hysteresis 50 / 200 / 400 mVVIH 2 V min, VIL 0.8 V max, pull-down 125 / 350 / 800 kOhmVery similar digital thresholds; U1 gives explicit hysteresis spread
Enable / sleep control pin~SLP~ active-low sleep controlEN enable / sleep controlSame function class, different polarity and naming
WAKE pin thresholdsVIH VBAT - 1 V to VBAT + 0.3 V, VIL -0.3 V to VBAT - 3.3 VVIH VSUP - 1.8 V, VIL VSUP - 3.85 VThresholds differ; firmware and interface assumptions may not port 1:1
LIN pull-up / terminationIntegrated termination resistor, extracted values 20 / 30 / 47 kOhmIntegrated pull-up 20 / 45 / 60 kOhm, feature summary says 45 kOhm nominalPull-up network values differ
LIN capacitance30 pF max25 pFIC1 is slightly lower
Data rateUp to 20 kBdTX up to 20 kbps, RX up to 100 kbpsIC1 explicitly supports faster receive path
Temperature rangeJunction / virtual junction -40 C to +150 CJunction -40 C to +150 C operating, abs max to 165 CSimilar operating range; IC1 has higher absolute max junction rating
ESD robustnessExplicit: +-6 kV IEC 61000-4-2 on LIN/VBAT/WAKE, stronger HBM/CDM detailProtection features listed, but less ESD detail in extracted sectionU1 provides more explicit ESD numbers
Package / footprint style in project8-pin device with dual GND pins in the symbol8-pin device plus EP on pin 9 in the symbolPin-count presentation differs in your schematic symbols
Pinout comparison

Table

Pin #U1IC1Difference
1RXDRXDSame
2~SLP~ENSame control role class, but different naming and likely different logic interpretation
3~WAKE~WAKESimilar purpose, naming polarity differs
4TXDTXDSame
5GNDGNDSame
6LINLINSame
7VBATVSUPSame supply role, different naming
8INHINHSame
9GNDEPMajor package difference in the current symbols: U1 shows a second GND pin, while IC1 shows an exposed pad
Main takeaways

Table

TopicSummary
Best electrical robustnessIC1
Best supply-voltage flexibilityIC1 with 4.5 V to 36 V operation
Stronger INH output capabilityU1
Better-extracted low-power current detailU1
More automotive-specific positioningIC1
Biggest practical migration riskControl-pin semantics and the package/pad difference at pin 9
The biggest differences are:
  • IC1 is electrically wider-range and more fault-tolerant.
  • U1 has a much stronger INH output capability.
  • The control pins are not a drop-in semantic match: ~SLP~ vs EN, and ~WAKE~ vs WAKE.
  • Your symbols also differ at pin 9: U1 has a second ground pin, while IC1 has an exposed pad.
If you want, I can also make a second table that is strictly parameter-by-parameter with only numeric electrical specs side by side.
Numeric-only comparison table
Check symbol mismatches
Compare standby behavior
Sign up to send
Generate a markdown-formatted table to compare U1, IC1. Highlight the main diffe...
nico

nico

@copilot Generate a markdown-formatted table to compare U1, IC1. Highlight the main differences between them. I am especially interested in the electrical differences (maximum ratings, input and output voltages, currents, etc), pinout differences, tolerances, and main features.
1y

copilot

Here's a markdown-formatted table comparing the two components, U1 (TJA1021TK/20/C,118) and IC1 (TLIN1021ADRBRQ1) with the important parameters and their corresponding specifications.

Table

ParameterU1: TJA1021TK/20/C,118IC1: TLIN1021ADRBRQ1
ManufacturerNXPTexas Instruments
Maximum Supply Voltage (Vsup)27 V18 V
Typical Operating Voltage12 V12 V
Voltage on WAKE_N Pin (VIH)$\text{VBAT} - 1 , \text{V}$ to $\text{VBAT} + 0.3 , \text{V}$N/A
Voltage on WAKE Pin (VIL)-0.3 V to $\text{VBAT} - 3.3 , \text{V}$N/A
Wake-up Time7 µs to 50 µsN/A
RXD Pin ConfigurationOpen-drain, requires external pull-up resistorOpen-drain, requires external pull-up resistor
Pinout Differences9 pins (RXD, SLP, WAKE, TXD, GND, LIN, VBAT, INH, GND)9 pins (RXD, EN, WAKE, TXD, GND, LIN, VSUP, INH, EP)
Main FeaturesLIN 2.x/SAE J2602 transceiverLIN 2.x transceiver with integrated wake function
Operating Temperature Range-40 °C to +150 °C-40 °C to +150 °C
Dynamic CharacteristicsDominant wake-up time on WAKE_N (typ) = 30 μs\mu \text{s}N/A
Key Differences
  • Manufacturer: U1 is manufactured by NXP, while IC1 is from Texas Instruments.
  • Maximum Supply Voltage: U1 has a higher maximum supply voltage tolerance (27 V) compared to IC1 (18 V).
  • Pinout Differences: U1 includes pins for both SLP and WAKE, while IC1 separates these functionalities as SLP_N and WAKE_N.
  • WAKE Pin Requirements: U1 uses specific high and low-level input voltages for the WAKE_N pin.
Would you like a more detailed analysis or specifications on any particular parameter?
1y
6
What should I be aware of if I need to make sure my design can accept any of the...
nico

nico

What should I be aware of if I need to make sure my design can accept any of these ICs? Focus on electrical characteristics, pinout and LIN differences @copilot
2y

copilot

When designing a circuit that can accept any of the ICs mentioned (TJA1021BT/0Z, TJA1021TK/20/C,118, and TLIN1021ADRBRQ1), you need to consider several factors, including electrical characteristics, pinout differences, and the LIN (Local Interconnect Network) protocol features they support. Here's a breakdown of what to consider for each aspect:
Electrical Characteristics
  1. Supply Voltage ((V_{SUP})/(V_{BAT})): Ensure the supply voltage range is compatible across all devices. Commonly, LIN transceivers operate within a similar voltage range, but verifying each IC's datasheet is crucial to ensure they match.
  2. Input/Output Levels for LIN Communication: Check the input HIGH/LOW and output HIGH/LOW voltage levels for the RXD, TXD, and LIN pins. These levels dictate the logic level compatibility and are critical for reliable communication.
  3. Quiescent Current and Power Consumption: For battery-powered applications, the quiescent current ((I_{Q})) and overall power consumption are important. Differences might exist between ICs.
  4. ESD Protection Level: Considering the ESD protection rating of each device can be important, especially in environments prone to static discharges.
Pinout Differences
Comparing the pinouts for each IC, note these key differences and ensure your design can accommodate them:
  1. Common Pins: RXD, TXD, GND, LIN, and a supply voltage pin (labeled as (V_{BAT}) or (VSUP)) exist on all three devices. This commonality will be the foundation of your universal design.
  2. Control and Configuration Pins:
    • SLP_N/SLP and EN: These pins are used for sleep mode control. The TJA1021BT/0Z and TJA1021TK/20/C,118 use SLP_N and SLP, respectively, whereas the TLIN1021ADRBRQ1 uses an EN (enable) pin for enabling the device. You might need to use a jumper or a switch configuration to select between these control methods.
    • WAKE_N/WAKE and WAKE: These pins are responsible for wake-up functionality. Similar to the sleep control pins, you might need a configurable solution to accommodate the differences.
  3. Protection and Diagnostics: The INH (inhibit) pin is present in all ICs, used for disabling the LIN bus output and possibly providing diagnostic functionality. The handling of this pin might require special attention to ensure compatibility.
  4. Ground and Exposed Pads (EP): All ICs have GND pins, but the TLIN1021ADRBRQ1 includes an Exposed Pad (EP) for enhanced thermal dissipation, which might not be present on others. Design your PCB to optionally connect the EP to GND if used.
LIN Protocol Differences
  • LIN Standard Compliance: Confirm that all ICs support the required LIN protocol version for your application. While LIN is designed to be backward compatible, newer versions offer enhanced features that may not be supported by all ICs.
  • Bus Speed and Timing Characteristics: The maximum LIN bus speed (bit rate) and timing characteristics should be verified across all ICs to ensure they match the requirements of your network.
  • Physical Layer Capabilities: LIN physical layer capabilities, like slope control and wake-up functionalities, may vary. Ensure that all selected ICs meet the minimum requirements for your application.
Considering these factors will ensure your design is flexible enough to accommodate any of the mentioned ICs. Given the variability, implementing configurable connections (such as jumpers) and/or using programmable logic (like a small MCU to manage pin differences) could provide the necessary flexibility for supporting different IC options.
2y
4
Generate a markdown-formatted table to compare IC2, U1, IC1. Highlight the main ...
nico

nico

@copilot Generate a markdown-formatted table to compare IC2, U1, IC1. Highlight the main differences between them. I am especially interested in the electrical differences (maximum ratings, input and output voltages, currents, etc), pinout differences, tolerances, and main features.
2y

copilot

To compare IC2 (TJA1021BT/0Z by NXP), U1 (TJA1021TK/20/C,118 by NXP), and IC1 (TLIN1021ADRBRQ1 by Texas Instruments), I've focused on their electrical characteristics, pinouts, tolerances, and key features based on the provided excerpts. Note that some specific values might have been assumed when direct data was not provided. Differences are highlighted to assist in decision-making based on your specific requirements.

Table

Feature/SpecificationIC2 (TJA1021BT/0Z)U1 (TJA1021TK/20/C,118)IC1 (TLIN1021ADRBRQ1)
ManufacturerNXPNXPTexas Instruments
Voltage Range (V)5.5 to 27cc5744b3−ccac−58e9−a336−3fa010b5c711cc5744b3-ccac-58e9-a336-3fa010b5c7115.5 to 27cc5744b3−ccac−58e9−a336−3fa010b5c711cc5744b3-ccac-58e9-a336-3fa010b5c7114.5 to 36b703f775−ce3c−58bc−9916−1557d44f84bbb703f775-ce3c-58bc-9916-1557d44f84bb
Output Voltages (V)--RXD: VOL = 0.60db473f6−22db−5436−b42e−b3dfb580d3700db473f6-22db-5436-b42e-b3dfb580d370
Output Currents (mA)--IOL = 1.5 (Low-level output current, open drain)0db473f6−22db−5436−b42e−b3dfb580d3700db473f6-22db-5436-b42e-b3dfb580d370
Protection FeaturesHigh ESD robustness, transmit data (TXD) dominant time-out, protection against automotive transientsd3678135−eb6d−54df−bbe2−c2258f64acf3d3678135-eb6d-54df-bbe2-c2258f64acf3Similar to IC2Functional Safety-Capableb703f775−ce3c−58bc−9916−1557d44f84bbb703f775-ce3c-58bc-9916-1557d44f84bb
Main FeaturesLIN 2.x/SAE J2602 transceiver, ESD protectioncc5744b3−ccac−58e9−a336−3fa010b5c711cc5744b3-ccac-58e9-a336-3fa010b5c711Similar to IC2Wide input voltage range, up to 20 kbps transmit data rate, low-power mode wake-up supportb703f775−ce3c−58bc−9916−1557d44f84bbb703f775-ce3c-58bc-9916-1557d44f84bb
Pinout Differences8 pins: Includes SLP_N, WAKE_Ncc5744b3−ccac−58e9−a336−3fa010b5c711cc5744b3-ccac-58e9-a336-3fa010b5c7119 pins: Includes SLP, WAKE, extra GND867f5887−b6b0−5136−9cfd−22d246f436a0867f5887-b6b0-5136-9cfd-22d246f436a09 pins: Includes EN, WAKE, EP (Exposed Pad)0db473f6−22db−5436−b42e−b3dfb580d3700db473f6-22db-5436-b42e-b3dfb580d370
Tolerances/RobustnessThermally protected, short-circuit proofd3678135−eb6d−54df−bbe2−c2258f64acf3d3678135-eb6d-54df-bbe2-c2258f64acf3Similar to IC2Designed for functional safety systemb703f775−ce3c−58bc−9916−1557d44f84bbb703f775-ce3c-58bc-9916-1557d44f84bb
Data Rates--2.4-kbps to 20-kbps transmit, up to 100-kbps receive9a656925−12e0−5390−8dce−645166d9c7d69a656925-12e0-5390-8dce-645166d9c7d6
Key Differences Highlighted:
  • Voltage Range: IC1 has a wider operating voltage range ($4.5 to 36V$) compared to IC2 and U1 ($5.5 to 27V$), making it more versatile for different supply voltages.
  • Pinout: IC1 and U1 offer 9 pins including additional functionalities and protection features. IC1 includes an EN (Enable) pin and an EP (Exposed Pad) for better thermal dissipation.
  • Output Characteristics: Exclusive detailed output characteristics (voltage and current specifications) are provided for IC1, indicating more precise control and integration information.
  • Main Features and Protection: IC1 is noted for its functional safety capability and wide range of operation, which could be critical for automotive applications requiring a high degree of reliability and versatility.
These differences could play a significant role in selecting the most suitable component based on your project's voltage requirements, desired data rates, and specific features like functional safety or enhanced protection against environmental conditions.
2y
nico

nico

what are other parts that I could use as a replacement?
2y

copilot

For replacements or alternatives to the described components (LIN transceivers), the selection would depend on your specific needs regarding functionality, electrical specifications, packaging, and compliance standards. Below, I'll list potential replacements for each part based on common functionalities and applications, noting that operational specifications such as voltage ranges, current capabilities, and special features should be cross-checked against your project requirements.
For IC2 (TJA1021BT/0Z) and U1 (TJA1021TK/20/C,118)
Both are LIN transceivers from NXP with relatively similar specifications. Here are alternatives within and outside NXP's product lines:
  • NXP MC33662: This LIN transceiver offers robust ESD performance and is optimized for low power consumption. It's suitable for applications requiring efficient energy usage.
  • STMicroelectronics L9637: A monolithic bus driver with integrated transceiver intended for LIN bus applications. It has features that support robust data communication.
  • Infineon TLE7259-3GE: Another LIN transceiver option that stands out for its minimal electromagnetic emission (EME) and high immunity against electromagnetic interference (EMI), ideal for automotive and industrial environments.
For IC1 (TLIN1021ADRBRQ1)
This part is a Texas Instruments LIN transceiver with specific features aimed at reliability and safety applications. Alternatives could include:
  • Texas Instruments SN65HVD233: A CAN transceiver that, while primarily designed for CAN networks, offers robustness in terms of ESD protection and is suitable for automotive environments. It could be considered if your application can accommodate CAN communication.
  • Infineon TLE7268SK: A dual LIN transceiver designed for high reliability in automotive applications, with a focus on minimizing power consumption and providing high ESD robustness.
General Considerations
When looking for replacements or alternatives:
  • Check Compatibility: Ensure the pinout, package size, and electrical characteristics (e.g., voltage levels, current capabilities) align with your needs.
  • Evaluate Features: Consider specific needs such as wake-up functionality, protection features (transient protection, thermal shutdown), and data rate capabilities.
  • Compliance and Certifications: For automotive or industrial applications, confirm that prospective replacements meet the necessary standards (e.g., AEC-Q100 for automotive).
Always refer to the datasheets of potential replacement components for detailed specifications and ensure they align with your project's requirements before making a final selection.
2y
5
IC2
Manufacturer Part Number
TJA1021BT/0Z
U1
Not Recommended for New Designs
Manufacturer Part Number
TJA1021TK/20/C,118
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
    jharwinbarrozo
    16.2k
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • RMCF0805JT47K0
    RMCF0805JT47K0
    General Purpose Thick Film Standard Power and High-Power Chip Resistor 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film Features: - RMCF – standard power ratings - RMCP – high power ratings - Nickel barrier terminations standard - Power derating from 100% at 70ºC to zero at +155ºC - RoHS compliant, REACH compliant, and halogen free - AEC-Q200 compliant
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10 µF 16 V Aluminum - Polymer Capacitors Radial, Can - SMD 30mOhm 2000 Hrs @ 105°C #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric)
    jharwinbarrozo
    1.1M
  • 1070TR
    1070TR
    Battery Holder (Open) Coin, 20.0mm 1 Cell SMD (SMT) Tab bate or batt #forLedBlink
    jharwinbarrozo
    700.5k

[Demo] Part comparison

[Demo] Part comparison thumbnail
Welcome to your new project. Imagine what you can build here.

Properties

Properties describe core aspects of the project.

Pricing & Availability

Distributor

Qty 1

Digi-Key

$0.55–$1.36

LCSC

$2.39

Mouser

$2.32

Controls