copilot

1. MQ-135 (U3):
   • [U3]:VH+ to [A1]:+5V_1
   • [U3]:VH- to [A1]:GND2
   • [U3]:A1 to [A1]:AD0
   • [U3]:A2 to [A1]:AD1
2. TCS3200D-TR (This is your M1, a color sensor):
   • [M1]:VCC to [A1]:+5V_2
   • [M1]:GND to [A1]:GND3
   • [M1]:OUT to [A1]:12
   • [M1]:S0, [M1]:S1, [M1]:S2, [M1]:S3 to control pins of your choice (e.g., [A1]:A2, [A1]:A3, [A1]:A4, [A1]:A5)
3. Grove - CO2 & Temperature (U1):
   • [U1]:VCC to [A1]:+5V_3
   • [U1]:GND to [A1]:GND1
   • [U1]:SDA to [A1]:SDA
   • [U1]:SCL to [A1]:SCL
4. IRA-S230ST01 (PIR1):
   • [PIR1]:SOURCE to [A1]:+5V_2
   • [PIR1]:GND to [A1]:GND5
   • [PIR1]:DRAIN to [A1]:AD6
5. LCD-016N002L (U2):
   • [U2]:VDD to [A1]:+5V_3
   • [U2]:VSS to [A1]:GND4
   • [U2]:RS, [U2]:R/~W, [U2]:E to control pins (e.g., [A1]:10, [A1]:11, [A1]:13)
   • [U2]:DB0 to [U2]:DB7 -> compatible digital pins on [A1] (e.g., [A1]:22 to [A1]:29)
   • [U2]:K and [U2]:A should be connected appropriately for the backlight.
6. Motores (M2, M3, M4):
   • [M2]:+ to motor driver control (to be defined, e.g., [A1]:30)
   • [M3]:+ to motor driver control (to be defined, e.g., [A1]:32)
   • [M4]:+ to motor driver control (to be defined, e.g., [A1]:34)
   • [M2][M3][M4]:- to GND

Cpp
#include 
#include 

// Define connections and setup
LiquidCrystal lcd(10, 11, 22, 23, 24, 25, 26, 27);
#define MQ135_PIN A0
#define TCS3200_OUT_PIN 12
#define PIR_PIN A6
#define MOTOR_ORGANIC 30
#define MOTOR_INORGANIC 32
#define MOTOR_RECYCLABLE 34

void setup() {
  // Initialize LCD
  lcd.begin(16, 2);
  
  // Initialize pins
  pinMode(MQ135_PIN, INPUT);
  pinMode(TCS3200_OUT_PIN, INPUT);
  pinMode(PIR_PIN, INPUT);
  pinMode(MOTOR_ORGANIC, OUTPUT);
  pinMode(MOTOR_INORGANIC, OUTPUT);
  pinMode(MOTOR_RECYCLABLE, OUTPUT);
  
  Serial.begin(9600);
}

void loop() {
  int mq135Value = analogRead(MQ135_PIN);
  int pirState = digitalRead(PIR_PIN);

  if (pirState == HIGH) {
    delay(100);  // debounce delay
    
    // Read MQ135 Sensor
    Serial.println("Detecting MQ135...");
    if (mq135Value > THRESHOLD_ORGANIC) {
      lcd.print("ORGANIC");
      triggerMotor(MOTOR_ORGANIC);
    }

    // Read TCS3200 Sensor for color check
    int colorValue = digitalRead(TCS3200_OUT_PIN);
    if (colorValue == COLOR_THRESHOLD_RECYCLABLE) {
      lcd.print("RECYCLABLE");
      triggerMotor(MOTOR_RECYCLABLE);
    } else {
      lcd.print("INORGANIC");
      triggerMotor(MOTOR_INORGANIC);
    }
  }
  delay(1000); // Loop delay
}

void triggerMotor(int motorPin) {
  digitalWrite(motorPin, HIGH);
  delay(2000);  // Activate for 2 seconds
  digitalWrite(motorPin, LOW);
}

• Asegúrate de definir los valores de umbral adecuados como THRESHOLD_ORGANIC y COLOR_THRESHOLD_RECYCLABLE para tu aplicación, dependiendo de cómo midas gases y colores.
• Asegúrate de probar y ajustar los tiempos de activación de los motores para tus puertas.
• Considera calibrar los sensores en un entorno controlado antes de poner en marcha el sistema.