PoE Ultrasonic Sensor Node Design

flux

0:46

Chat History
Project
BT1
C1
D1
ESP1
J1
J2
J3
LED1
LED2
LED3
MK1
R1
U1
U2
U3
U4
U5
Below is a detailed recommendation for the layer stackup and trace parameters to target a 100 Ω differential impedance for your Ethernet pairs:
Recommended 2-Layer PCB Stackup
  • Top Layer:
    • Purpose: Signal layer for high-speed differential pairs and other routing.
    • Copper Weight: Typically 1 oz (≈35 µm).
    • Trace Environment: Use microstrip routing; traces on the top layer will reference the bottom continuous ground plane.
  • Bottom Layer:
    • Purpose: Solid ground plane for return paths and impedance control.
    • Coverage: Ideally, a full-plane ground to provide a reliable reference for the top-layer signals.
  • PCB Overall Thickness:
    • A standard value of 1.6 mm is common.
    • The effective dielectric height between the top copper layer and the bottom ground plane should ideally be kept low (commonly in the range of 5–6 mil or around 0.127–0.15 mm) to help maintain controlled impedance on the top layer.
  • Dielectric Constant (Er):
    • Use typical FR4 values (Er ≈ 4.3–4.7). Verify with your PCB fabrication house as this factor influences impedance calculations.
Differential Pair Trace Parameters
Based on the above stackup, simulation and empirical guidance (using typical microstrip equations or PCB impedance calculators) suggest:
  • Differential Trace Width: Approximately 10 mil (0.254 mm)
  • Spacing (Gap) Between Traces: Approximately 7 mil (0.178 mm)
  • Target Differential Impedance: Approximately 100 Ω
Note: These values are common starting points for 1 oz copper on a 1.6 mm board when you have a ground plane 5–6 mil below the top copper. In practice, you should use an impedance calculator or simulation tool (e.g., Saturn PCB Toolkit) to fine-tune the dimensions based on your specific stackup details (e.g., actual dielectric thickness, FR4 material variations, and fabrication tolerances).

Summary Table

ParameterRecommendation
Board Type2-layer PCB
Board Thickness1.6 mm
Copper Weight (Top Layer)1 oz (≈ 35 µm)
Top LayerSignal layer (microstrip configuration)
Bottom LayerContinuous Ground Plane
Dielectric Height (Top-to-Ground)~5–6 mil (≈0.127–0.15 mm)
FR4 Dielectric Constant (Er)Approximately 4.3–4.7
Differential Trace Width~10 mil (0.254 mm)
Differential Spacing~7 mil (0.178 mm)
Target Differential Impedance100 Ω
By ensuring that your stackup maintains a low and consistent dielectric separation between the top layer and the ground plane, and by using the recommended trace dimensions, you’ll be well on your way to achieving 100 Ω differential impedance. Always confirm these dimensions with an impedance calculator (considering your specific PCB manufacturer’s process) for final verification.
Would you like to receive any additional recommendations regarding layer stackup details or further PCB design tips before you begin routing?
Update project properties
Simulate differential impedance
Verify manufacturing tolerances
Apply settings and check guidelines
325 days

Ready.

Sign up to send
U2
J3
MK1
End of Life
ESP1
D1
C1
Capacitance
Capacitance
U1
U4
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • Power Net Portal
    Power Net Portal
    Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
    jharwinbarrozo
    11.4M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
    jharwinbarrozo
    15.5k
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • RMCF0805JT47K0
    RMCF0805JT47K0
    47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
    jharwinbarrozo
    1.1M
PoE-powered ultrasonic sensor node thumbnail
Welcome to your new project. Imagine what you can build here.

Properties

Properties describe core aspects of the project.

Pricing & Availability

Distributor

Qty 1

Arrow

$3.00–$5.44

Digi-Key

$5.76–$7.08

LCSC

$4.21–$4.59

Mouser

$14.60

Verical

$5.34–$10.22

Assets

Assets are files uploaded to this project which can be used in various ways.

Controls