Part Review and Datasheet Update

flux

Updated the symbol labels and pin metadata, then audited the SOIC-16 land pattern. The detailed report is updated here: W25Q02JVSFIM Part Review.
Open items:
  • Pins 12–14 still display as N/C; the rename attempts did not persist, though their descriptions are correct.
  • The footprint geometry is broadly SOIC-16 wide-body compatible, but its source asset/model still references MAX3232ECWE+T.
Suggested next steps:
  1. Manually rebuild or replace pins 12–14 if strict NC display naming is required.
  2. Replace the footprint/3D model asset with a W25Q02JVSFIM-specific SOIC-16 wide-body asset.
  3. Verify final package dimensions directly against the Winbond mechanical drawing before publishing.
A

adrian95

Replace the footprint/3D model asset with a W25Q02JVSFIM-specific SOIC-16 wide-body asset.

flux

I’ll replace the inherited MAX3232 footprint/model references with a W25Q02JVSFIM-specific SOIC-16 wide-body footprint/model asset, then verify the layout metadata no longer points to MAX3232.

flux

Replaced the footprint and 3D model rule references with W25Q02JVSFIM-specific SOIC-16W assets and removed the old MAX3232 footprint/model assets. I updated the report here: W25Q02JVSFIM Part Review.
Open items:
  • The layout rule references are corrected, but the inspector still shows cached/generated MAX3232 payload details inside the rendered geometry; a layout refresh/rebuild may be needed to fully regenerate the geometry text.
Suggested next steps:
  1. Refresh/rebuild the footprint geometry from the new W25Q02JVSFIM asset.
  2. Re-check the part before publishing.
  3. Fix the remaining pins 12–14 N/C display labels if strict naming consistency is required.
Refresh, verify, fix labels
Refresh footprint geometry
Re-check before publishing
Fix NC labels
Verify 3D model
Sign up to send

Files

Pins

Symbol

Layout

3D View

/HOLD (IO3)
NC
NC
NC
/CS
DNU
/RESET
CLK
DNU
/WP (IO2)
DI (IO0)
GND
VCC
NC
NC
DO (IO1)
Name
Pin #
Type
Section
Pin Group
Orientation
Order
Sub-symbol
Pin Description
/HOLD (IO3)
1
Bi-Directional
SPI
Active-low HOLD input in SPI mode; IO3 in Quad SPI/QPI modes. Pull high when hold function is not used.
VCC
2
Power In
Power
Positive supply input, 2.7 V to 3.6 V operating range.
/RESET
3
Input
Control Bus
Active-low hardware reset input.
NC
4
Not Connected
NC
No connect; leave unconnected.
NC
5
Not Connected
NC
No connect; leave unconnected.
DNU
6
Reserved
NC
Do not use; leave unconnected per datasheet guidance.
/CS
7
Input
SPI
Active-low chip select input for SPI/QSPI transactions.
DO (IO1)
8
Bi-Directional
SPI
Serial data output in standard SPI; IO1 in Dual/Quad SPI/QPI modes.
/WP (IO2)
9
Bi-Directional
SPI
Active-low write protect input in SPI mode; IO2 in Quad SPI/QPI modes. Pull high when write-protect function is not used.
GND
10
Ground
Ground
Ground reference.
DNU
11
Reserved
NC
Do not use; leave unconnected per datasheet guidance.
NC
12
Not Connected
NC
No connect; leave unconnected.
NC
13
Not Connected
No Connect
No connect; leave unconnected.
NC
14
Not Connected
No Connect
No connect; leave unconnected.
DI (IO0)
15
Bi-Directional
SPI
Serial data input in standard SPI; IO0 in Dual/Quad SPI/QPI modes.
CLK
16
Input
SPI
Serial clock input for SPI/QSPI/QPI operation.

W25Q02JVSFIM