Part Datasheet Review and Validation

flux

Completed the datasheet review for TLE92466EDXUMA1. The official Infineon datasheet URL was already set, and the symbol pin-number/name mapping matches the datasheet’s 36 leads plus exposed cooling tap.
Open items flagged:
  • Part Type is inaccurate: currently “Electromechanical Components”; should be an integrated low-side solenoid driver IC / power switch driver.
  • Description is misleading: it says “1:1 N-Channel 2.7A,” but this is a six-channel solenoid driver; 2.7 A applies to parallel-channel capability.
  • Pin Type and Pin Description properties are not populated.
  • Pin 37 is electrically OK as GND, but should be described as Cooling Tap / exposed pad.
I saved the full review here: TLE92466EDXUMA1 Part Datasheet Cross-Check.
A

adrian95

Fix the metadata, populate pin descriptions and types, then rerun a symbol/footprint review.

flux

I’ll update the part metadata and terminal pin properties from the Infineon datasheet, then re-inspect the schematic symbol and footprint for mismatches.

flux

Metadata is corrected; I’m now applying datasheet-derived pin descriptions and electrical types to all 37 terminals.

flux

Fixed the metadata and populated all 37 terminal Pin Description and Pin Type properties from the Infineon datasheet. I reran the review: symbol pin mapping and footprint pad count now match the datasheet, with no remaining pin-name/number/description mismatches.
Open items:
  • Exact footprint copper/mask/stencil geometry could not be numerically verified from the exposed layout data, but pad count/designators and visible package form are consistent with PG-DSO-36-72.
Updated review file: TLE92466EDXUMA1 Part Datasheet Cross-Check.
Fix footprint and review
Verify footprint geometry
Run ERC and DRC
Check BOM readiness
Add thermal notes
Sign up to send

Files

Pins

Symbol

Layout

3D View

Name
Pin #
Type
Part Type
Pin Description
Pin Orientation
LOAD0
1
Output
Terminal
Output for channel 0 low-side solenoid driver.
FWD0
2
Output
Terminal
Freewheeling diode connection for channel 0.
GNDP0
3
Ground
Terminal
Ground connection for channel 0 power stage.
Bottom
GND_1
4
Ground
Terminal
Ground; connect to GND.
Bottom
CSN
5
Input
Terminal
SPI chip select input; 3.3 V or 5.0 V logic level digital input.
SCK
6
Input
Terminal
SPI clock input; 3.3 V or 5.0 V logic level digital input.
SI
7
Input
Terminal
SPI serial data input; 3.3 V or 5.0 V logic level digital input.
VIO
8
Power In
Terminal
Supply for SPI Slave Out (SO) pin; connect to 3.3 V or 5.0 V supply.
SO
9
Output
Terminal
SPI serial data output; push-pull output compatible with 3.3 V or 5.0 V logic levels.
GND_2
10
Ground
Terminal
Signal ground; internally connected to cooling tap.
Bottom
FAULTN
11
Open Collector
Terminal
Fault/status output; open-drain output. Leave open if unused.
GND_3
12
Ground
Terminal
Signal ground; internally connected to cooling tap.
Bottom
LOAD5
13
Output
Terminal
Output for channel 5 low-side solenoid driver.
FWD5
14
Output
Terminal
Freewheeling diode connection for channel 5.
GNDP5
15
Ground
Terminal
Ground connection for channel 5 power stage.
Bottom
GNDP1
16
Ground
Terminal
Ground connection for channel 1 power stage.
Bottom
FWD1
17
Output
Terminal
Freewheeling diode connection for channel 1.
LOAD1
18
Output
Terminal
Output for channel 1 low-side solenoid driver.
LOAD2
19
Output
Terminal
Output for channel 2 low-side solenoid driver.
FWD2
20
Output
Terminal
Freewheeling diode connection for channel 2.
GNDP2
21
Ground
Terminal
Ground connection for channel 2 power stage.
Bottom
VBAT
22
Power In
Terminal
Battery supply voltage input; connect to battery voltage with reverse protection diode and EMC filter.
GND_4
23
Ground
Terminal
Signal ground; internally connected to cooling tap.
Bottom

TLE92466EDXUMA1