Chat

Welcome to Flux

Treat Flux like your intern. Tell it what you'd like to build and it'll get to work. You can also ask it questions, brainstorm ideas, and teach it your preferences. Learn More

Explain this part
Write a part description
Describe each pin
Operating conditions
Electrical max ratings
Part Specifications
Application circuits
Verify Part Details
Recommend similar parts
Check availability & lifecycle
Sign up to send
basic orduino
yassine3d

yassine3d

@copilot basic orduino
2y

copilot

Your question is quite broad, could you please clarify what you're looking for? Are you looking for information on how to use an Arduino with the ESP32-H2-WROOM-03 module in your project, or are you interested in guidance on starting a new project with a basic Arduino board? Please provide more context so I can assist you better.
2y
Someone is typing...
2
Help me set up a barebones, UART or USB programmable PCB using this module with ...
av-8

av-8

@copilot Help me set up a barebones, UART or USB programmable PCB using this module with an LED attached to a GPIO
2y

copilot

Sure! Here are the main connections required to make a basic, programmable PCB with an ESP32 module and an LED. For the ESP32, I've assumed you're using the ESP32-H2-WROOM-03 module as specified in the project description, and for simplicity, we'll use GPIO5 (Pin 10 - IO5) as our LED controlling GPIO.
For the LED, I'll assume it's a typical green LED with a forward voltage of 2V and current of 20mA. We would need a resistor to limit the current, which can be calculated using Ohm's law:
[R = \frac{V}{I}]
Where V is 3.3V - 2V = 1.3V (The voltage drop across the resistor must be the voltage difference between the GPIO voltage output level of the ESP32 module and the forward voltage of the LED) and I is 20mA = 0.02A, so therefore:
[R = \frac{1.3}{0.02} \approx 65 \Omega]
A standard nearest value to 65Ω is 68Ω. If you can't get a 68Ω resistor you can use a series or parallel combination of resistors to get the closest value.
Here are the basic connections you need to make now:
  • Connect IO5 (Pin 10) on the ESP32 to one end of the resistor.
  • Connect the other end of the resistor to the anode (longer pin) of the LED.
  • Connect the cathode (shorter pin) of the LED to GND (Pin 7) on the ESP32.
  • Connect GND (Pin 7) on the ESP32 to the ground of your power source.
  • Connect 3.3V (Pin 6) on the ESP32 to the power of your power source (3.3 volts).
For programming functionalities:
With UART:
  • Connect a UART to USB converter. Connect the U0TXD pin from the module to the RX pin on the converter, and the U0RXD pin to the TX pin on the converter. Also connect the GND (Pin 7) to the GND on the converter.
With USB:
  • A USB to serial chip like CP2102 can be used. They usually come with DTR and RTS outputs which can be connected to the GPIO0 and RST pins for auto-programming functionality. The RX and TX pins can be connected highlighting the correct orientation similar to the UART process.
I hope this helps. Let me know if you need further clarification or assistance!
2y
Someone is typing...
3
IO5
IO22
IO1
IO4
EN
NC

No results...

Learn to Add a Component

ESP32-H2-WROOM-03

ESP32-H2-WROOM-03 thumbnail
The ESP32-H2-WROOM-03 module is based on ESP32-H2, and can be vertically soldered to a PCB board. #espressif #WiFi #part

Properties

WiFi Module

Espressif

ESP32-H2-WROOM-03

espressif.com/sites/default/files/documentation/esp32-h2-wroom-03_datasheet_en.pdf

U

creativecommons.org/licenses/by/4.0/

parametric-v1

Pricing & Availability

Distributor

Qty 1

Controls