U5 Charge-Pump Regulator Overview

flux

Here’s a detailed overview of U5 in your design:
Component: U5 – LM27762DSSR charge-pump switching regulator
1. Purpose & Core Function
  • Generates both a regulated positive rail (OUT⁺) and negative rail (OUT⁻) from a single input (VIN).
  • Ideal when you need small bipolar supplies (e.g. ±2.5 V, ±5 V) but don’t want an inductor-based solution.
2. Key Features
  • Dual charge-pump architecture with internal 2 MHz oscillator and MOSFET switch array.
  • Adjustable outputs via external resistor dividers on FB⁺ and FB⁻ pins.
  • Built-in LDO regulators for low-noise, tightly regulated rails.
  • Power-Good (PGOOD) flag (open-drain) to indicate when both outputs are in regulation.
  • Shutdown pins (EN⁺, EN⁻) enable individual disabling of each pump, reducing quiescent current.
  • Capable of up to 250 mA per output.
3. How It Operates in the Circuit
  1. Oscillator & Pumping Stage
    • A 2 MHz clock drives internal switches that shuttle charge into flying capacitors (C1+, C1–).
  2. Switch-to-Output Stage
    • Pumped voltage is steered through an internal LDO stage to produce regulated OUT⁺ and OUT⁻.
  3. Feedback & Regulation
    • External resistor dividers on FB⁺/FB⁻ set the exact output voltages.
    • The chip adjusts switch duty-cycle and LDO gate drive to maintain regulation.
  4. Monitoring & Control
    • PGOOD asserts low when both rails are within regulation bands.
    • EN pins allow power-down or sequencing.
4. Common Applications
  • Hi-Fi audio headphone amplifiers (bias rails)
  • Op-amp power biasing in precision analog circuits
  • Powering data converters (ADC/DAC supply rails)
  • Interface supplies for mixed-signal or wireless modules
  • Hand-held instrumentation where ± rails are needed without large inductors
5. Notable Characteristics
  • High switching frequency (2 MHz) allows use of small SMD capacitors (0603/0805).
  • Low-ESR pump caps yield better efficiency and lower output impedance.
  • Exposed pad WSON package for superior thermal performance.
  • Wide temperature range (–40 °C to +85 °C).
6. Series & Family Context
The LM27762 belongs to TI’s family of high-frequency, dual-output charge-pump regulators.
  • Fixed-output variants (e.g. LM27762-5.0) provide factory-set ±5 V with no external divider.
  • Adjustable versions (LM27762DSSR) let you pick any ± output within the device’s range (typically ±1.5 V to ±6 V).
  • Key differences across the family:
    • Output voltage options (fixed vs. adjustable)
    • Maximum output current (200–300 mA)
    • Package styles (WSON vs. QFN)
  • Use-case trade-offs:
    • Choose fixed versions for simpler BOM when only one bipolar voltage is needed.
    • Choose the adjustable LM27762DSSR for flexibility in mixed-supply or multi-rail systems.
By using U5, your signal generator gains compact, inductor-less ± rails that are essential for driving the op-amps (e.g., U1–U3) and delivering clean, stable waveforms.
Specify output voltages
Add pump caps
Set shutdown behavior
Enable PGOOD pin
Thermal considerations
how does the feedback loop work on U1?
nico

nico

@copilot how does the feedback loop work on U1?
2y

copilot

The feedback on the Operational Amplifier (Op-Amp) U1 is implemented through a resistor R1 and a resistor R3.
In this case, U1 is configured in a non-inverting amplifier configuration. The input signal is applied to the non-inverting input (U1:+), while the output (U1:OUTPUT) is fed back to the inverting input (U1:-) via resistors R1 and R3, forming a voltage divider.
The feedback helps to stabilize the amplifier’s gain and improve its performance. It works as follows:
  • The Op-Amp produces an output signal in response to the difference between its input signals.
  • A portion of the output signal is fed back to the inverting input via resistors R3 and R1 that act as voltage dividers, hence the name 'feedback'.
  • Since the feedback signal is in phase with the input, it counteracts any increase or decrease in the input signal to maintain a stable output.
This feedback configuration gives us a voltage gain of:
Gain=1+R3R1 Gain = 1 + \frac{R3} {R1}
The exact values of the resistors (R3 and R1) in the divider help define the amplifier's closed-loop gain. Thus, by adjusting R1 or R3, you can control the gain of the op-amp circuit.
Also, in this case, R1 is connected to the ground, forming negative feedback, which is essential for amplifier stability, accuracy, and predictability. Negative feedback tends to decrease the output (due to the inverse phase) and is used in most amplifiers to improve bandwidth and distortion while stabilizing the gain.
2y
Someone is typing...
2
what is c2 accomplishing in the feedback loop?
nico

nico

@copilot what is c2 accomplishing in the feedback loop?
2y

copilot

The capacitor C2, according to the netlist, is directly connected between the output (OUTPUT pin) and the inverting input (- pin) of the operational amplifier U2. This setup constitutes a feedback loop.
C2 effectively operates as an integral component of a high-pass filter which is part of the configuration of the op-amp U2. In the feedback loop of an amplifier, having a capacitor allows the circuit to preferentially amplify higher frequencies more than lower frequencies, creating a 'high-pass' effect.
The exact cut-off frequency of the high-pass filter is determined by the values of the capacitor C2 and the resistor R5, in line with the formula:
fc=12πR5C2 f_{c} = \frac{1} {2 \pi R5 C2}
Where:
  • $f_{c} $ is the cut-off frequency,
  • $R5$ is the resistance connected to the capacitor in feedback loop, and
  • $C2$ is the capacitance value of the capacitor in the feedback loop.
In the Fourier domain, the phase of the output signal is shifted by 90 degrees by the capacitor which can be useful for specific applications where a phase shift or waveform shaping is required. However, more information about the whole circuit and its intended application is needed to say more about the exact influence and role of C2 in this circuit.
2y
Someone is typing...
3
R9
Resistance
51.1kΩ
C20
Capacitance
10uF
C6
Capacitance
10uF
R10
Resistance
41.2kΩ
-2.7V
+2.7V
C21
Capacitance
4.7uF
+5V
VBUS
R14
Resistance
Resistance
Resistance
5.1kΩ
C24
Capacitance
4.7uF
C4
Capacitance
4.7uF
+5V
C5
Capacitance
1uF
+5V
R12
Resistance
49.9kΩ
R11
Resistance
41.2kΩ
C19
Capacitance
0.1uF
R13
Resistance
Resistance
Resistance
5.1kΩ
U5
Manufacturer Part Number
LM27762DSSR
CC2
CC1
D1
CC2
Square_wave
RV1
Resistance
100kΩ
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
    jharwinbarrozo
    16.5k
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • RMCF0805JT47K0
    RMCF0805JT47K0
    General Purpose Thick Film Standard Power and High-Power Chip Resistor 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film Features: - RMCF – standard power ratings - RMCP – high power ratings - Nickel barrier terminations standard - Power derating from 100% at 70ºC to zero at +155ºC - RoHS compliant, REACH compliant, and halogen free - AEC-Q200 compliant
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10 µF 16 V Aluminum - Polymer Capacitors Radial, Can - SMD 30mOhm 2000 Hrs @ 105°C #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric)
    jharwinbarrozo
    1.1M
  • 1070TR
    1070TR
    Battery Holder (Open) Coin, 20.0mm 1 Cell SMD (SMT) Tab bate or batt #forLedBlink
    jharwinbarrozo
    700.5k

Signal Generator

Signal Generator thumbnail
This project is a Signal Generator, designed to output waveforms such as sine, square and triangular waves. It leverages the capabilities of operational amplifiers (op-amps) like the LMV321 in combination with resistors and capacitors to shape the output signals. The design benefits from the op-amps' negative feedback to stabilize and regulate the signal output. #project #LMV321

Properties

creativecommons.org/licenses/by/4.0/

Pricing & Availability

Distributor

Qty 1

Digi-Key

$10.48–$10.82

LCSC

$2.65

Mouser

$12.50

Controls