Arduino Projects

Arduino Uno R3 Outline shale on the Silkscreen layer NOT A PART

AVR series Microcontroller IC 8-Bit 16MHz 256KB (128K x 16) FLASH 100-TQFP (14x14) #simplifiedFootprint #symbolwithtext #Arduino #Mega #2560

is a vertical mounting board with an LM393 comparator and 2 LEDs. #IoT #Arduino #part #sensor #LM393

This module is a minimalist Arduino Watch design. Consisting of a Microchip ATTINY85-20SU microcontroller, an OLED display for visual output, two user buttons for interface, and a Li-ion Battery for power. The schematic also includes graphic user interface with ISP for programming and minimal passive components for functionality. #project #Template #projectTemplate #reusable #module #simple-embedded #microchip #arduino #sublayout

1.3 inch oled IIC Serial White OLED Display Module 128X64 I2C SSD1306 12864 LCD Screen Board VDD GND SCK SDA for Arduino Black #Module #OLED #LCD

Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino

This board was developed for applications and installations where space is premium and projects are made as permanent set ups. Small, available in 3.3 V and 5 V versions, powered by ATmega328P.

Power Barrel Connector Jack 2.10mm ID (0.083"), 5.50mm OD (0.217") Through Hole, Right Angle The PJ-202A is a DC power jack connector (barrel jack) commonly used in electronic devices to provide a stable DC power input. It is designed for through-hole PCB mounting and supports a right-angle (horizontal) orientation, making it suitable for compact PCB layouts. This connector typically mates with a 2.0 mm center-pin DC plug and is widely used in consumer electronics, routers, embedded systems, and small power supply boards. Key Features Connector Type: DC power jack (barrel type) Center Pin Size: 2.0 mm Outer Diameter Compatibility: ~6.5 mm plug type Mounting Style: Through-hole Orientation: Right-angle / horizontal PCB mount Rated Current: up to 2.5 A Rated Voltage: up to 24 V DC ontact Configuration: 2 conductors with internal switch option Durability: ~5,000 insertion cycles Operating Temperature: -25°C to +85°C Flammability Rating: UL94V-0 plastic housing Typical Applications Embedded systems Arduino / DIY electronics power input Consumer electronics Router / modem power input Battery-powered device charging inputs DC-005 barrel jack #commonpartslibrary #connector #barrel #jack #tht

Motor Driver Power MOSFET Parallel 24-SSOP The TB6612FNG,C,8,EL is a dual H-bridge motor driver IC developed by Toshiba. It is designed to control the speed and direction of two DC motors or one bipolar stepper motor. This device uses low ON-resistance MOSFETs for efficient operation, resulting in lower heat generation and higher efficiency compared to traditional bipolar transistor-based drivers. It is widely used in robotics, motor control applications, and embedded systems. Key Features Motor Drive Capability Dual H-bridge driver (can drive 2 DC motors or 1 stepper motor) Output current: 1.2 A (continuous) per channel 3.2 A (peak) per channel Wide motor supply voltage range: 2.5 V to 13.5 V Logic & Control Logic supply voltage (VCC): 2.7 V to 5.5 V Compatible with 3.3 V and 5 V microcontrollers (e.g., ESP32, Arduino) Control inputs: IN1, IN2 (per channel for direction control) PWM input for speed control STBY (standby mode for power saving) Efficiency & Performance Low ON-resistance MOSFETs: Reduces power loss and heat High efficiency compared to L298N-type drivers Built-in shoot-through protection Protection Features Thermal shutdown protection Overcurrent protection Under voltage lockout (UVLO) #Commonpartslibrary #Motordriver #Integratedcircuit #TB6612

NRF24L01+ 2.4GHz Wireless RF Transceiver Module #commonpartslibrary #RF #wireless #arduino