Environmental exposure risk measuring device based on ESP32, ultraviolet light (UV) and CO2 gas sensor modules. It has a voltage booster based on MT3608 chip and a solar panel lithium battery charger with MPPT based on CN3791 chip.

First in the world hands-free Otherside communication device! You need only the board, spirit or ghost don't need to move the ouija anymore. Symbols will light up from the inside so you will be able to read your messages and spirit or ghost just need to turn on a red bottom entry LED. Two MEMS microphones allow your interlocutor to clearly hear your questions. WiFi connectivity gives you an opportunity to "dial" without a Medium anytime anywhere. And it has Bluetooth as well, because: "Everything is better with Bluetooth"! This board is powered by a single 10440(AAA) LiFePO4 battery that gives you up to 2 hours of seance. Designed by Vasyl Skral

The LoST 3296 board features an Low Power STM32, an RFM95 Module for LoRA connectivity and a connector to interface different sensors. You can hook up a UART module, I2C module and a module using the RS485. The board is powered by the USB-C port

This is one of the simplest FM transmitters that can be built. It does not require any tuning, and transmit frequency is crystal locked to 90MHz. It eliminates frequency drift common to LC-based FM transmitters. This design is best suited for broadcasting voice or music up to a distance of fifty metres depending on the antenna used.

AquaTimer is a programmable timer for 12V devices such as lighting, solenoid valves or pumps not only for aquariums. It has three switchable channels for currents up to 2A each and up to 5A in total. Connected lighting can be dimmed if desired and slowly faded in and out to simulate sunrises and sunsets. The internal RTC of the ATtiny is used as a clockwork in conjunction with a 32.768kHz crystal. A backup battery keeps the clock running even if the external power supply is interrupted. Settings are made using three buttons and the OLED display.

(AL8805W5) The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8805 part.

The Texas Instruments MSP430FR604x and MSP430FR603x family comprises highly integrated ultrasonic sensing and measurement system-on-chips (SoCs) designed specifically for water and heat metering applications. The featured components, including MSP430FR6047, MSP430FR60471, MSP430FR6045, MSP430FR6037, MSP430FR60371, and MSP430FR6035, deliver best-in-class ultrasonic water flow measurement with ultra-low power consumption. These microcontrollers excel with an active mode current consumption of approximately 120 µA/MHz and a standby mode power draw as low as 450 nA with a real-time clock (RTC) enabled. Key functionalities include a high-precision differential time-of-flight (dTOF) accuracy of less than 25 ps, integrated analog front-end, programmable pulse generation (PPG), and an analog comparator. They also interface directly with standard ultrasonic sensors up to 2.5 MHz and feature up to 256KB FRAM, robust RAM options, and integrated LCD drivers for up to 264 segments. The embedded low-energy accelerator (LEA) enhances digital signal processing capabilities, making these components ideal for battery-powered metering solutions. Peripherals include multiple enhanced serial communication interfaces, high-performance ADCs, DMA controllers, and a suite of timers and encryption modules. These features combine to offer a powerful solution for high-accuracy, low-cost, and ultra-low-power metering applications.

An ATtiny13 is more than sufficient to control almost any number of NeoPixels via an IR remote. The NeoController was originally developed as a tester for 800kHz NeoPixel strips. Since there was still so much flash left in the ATtiny13, an IR receiver was integrated so that some parameters can be controlled with an IR remote control. In this way, it is also suitable as a simple and cheap remote-controlled control unit for NeoPixels. Due to its small size (21.6mm x 11.4mm), it can be soldered directly to the LED strip without any problems. The power supply via a USB-C connection enables currents of up to 3A. There is still more than a third of the flash memory left for additional ideas.

The SparkFun ZOE-M8Q GPS Breakout is a high accuracy, miniaturized, GPS board that is perfect for applications that don't possess a lot of space. The on-board ZOE-M8Q is a 72-channel GNSS receiver, meaning it can receive signals from the GPS, GLONASS, BeiDou, and Galileo constellations. This increases precision and decreases lock time and thanks to the onboard rechargable battery you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.

This is the project template for the Raspberry Pi Pico 2, the latest addition and update to Pi Pico line up. Raspberry pi pico 2 is equipped with the RP2350, a cutting-edge, high-performance microcontroller designed with enhanced security and versatility in mind. Every element of its design has been upgraded, from the advanced CPU cores to the innovative PIO (Programmable I/O) interfacing subsystem. The Raspberry Pi Foundation has integrated a robust security architecture centered around Arm TrustZone for Cortex-M, ensuring data protection and integrity. Additionally, new low-power states and expanded package options broaden the range of applications, making the Pico 2 an ideal choice for diverse, power-sensitive projects. To learn more about what's the key differences between the original Pi Pico and the new Pi Pico 2, read our blog https://www.flux.ai/p/blog/whats-new-in-the-raspberry-pi-pico-2-a-showdown-with-the-original-raspberry-pi-pico #project-template #template #raspberry #pi #pico2 #newpico

This design is three parts, one a bandpass filter to allow only a certain frequency to come through the device, and the other two to filter and jam out different frequencies that would be coming near the device. The bandpass is set at 450MHz as is the common frequency for phones, the top jammer is set up for blocking out typical radio frequencies while the bottom is set to block frequencies above that of a phone signal. Vin=20 volts

Seeed Studio XIAO ESP32C6 is powered by the highly-integrated ESP32-C6 SoC, built on two 32-bit RISC-V processors, with a high-performance (HP) processor with running up to 160 MHz, and a low-power (LP) 32-bit RISC-V processor, which can be clocked up to 20 MHz. There are 512KB SRAM and 4 MB Flash on the chip, allowing for more programming space, and binging more possibilities to the IoT control scenarios.

Weather Station controlled by STM32F031F6P6 MCU. 2x humidity and temperature sensors. USB powered

This project is a reference design for an ESP32-WROVER-E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROVER #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

USB-C Digital Compass Module with STM32, HMC5883L, TM1637 Display, and Enhanced Power Protection (JLCPCB-Ready)

1. Overview: The Pundit pendant is a wearable AI transcription assistant. An innovative device designed to seamlessly integrate into daily activities, providing real-time transcription and note-taking capabilities. Combining advanced AI algorithms with state-of-the-art hardware components, the device offers crystal clear audio recording, durable construction, and convenient features such as cloud synchronization, weatherproofing, and a vibrant display for animations and expressions. 2. Hardware Specifications: * Rechargeable Battery: Lithium-ion battery providing up to 150 hours of continuous operation. * Construction: Durable aluminum body ensuring longevity and protection against wear and tear. * Audio Quality: High-fidelity microphone array for clear and accurate transcription, with noise cancellation technology. * Weatherproofing: Sealed construction to withstand various weather conditions, making it suitable for outdoor use. * Versatile Mounting: Equipped with a magnetic clasp for easy attachment to clothing or accessories. * Connectivity: Wi-Fi and Bluetooth connectivity for seamless data transfer and integration with other devices. * Charging: USB-C port for fast and convenient charging, with support for various power sources. * Input Microphone Array: Multiple microphones strategically placed for optimal audio capture and transcription accuracy. * Display: Colorful screen for displaying animations, expressions, and status indicators, enhancing user interaction and personalization. 3. Software Features: * Real-time Transcription: Utilizes AI algorithms for instant transcription of spoken words into text, with high accuracy. * Note-taking: Automatically creates and organizes notes based on conversations, timestamps, and contextual cues. * Audio Recording: One-touch button for initiating audio recording, with options for manual or automatic saving. * Cloud Synchronization: Syncs transcription data to the cloud for easy access and retrieval from any device. * Speech Recognition: Advanced speech recognition technology for identifying speakers and distinguishing between multiple voices. * Language Support: Multilingual support for transcription and note-taking in various languages. * Customization: User-configurable settings for adjusting transcription preferences, language models, and display animations. * Security: Encryption and authentication protocols to ensure the privacy and security of transcription data. 4. Dimensions and Weight: * Dimensions: Compact and lightweight design for comfortable wearability. * Weight: Minimal weight to prevent discomfort during prolonged use. 5. Compatibility: * Operating Systems: Compatible with iOS, Android, and other major operating systems. * Applications: Integration with popular productivity and communication apps for seamless workflow management. 6. Warranty and Support: * Warranty: Manufacturer's warranty covering defects in materials and workmanship. * Support: Dedicated customer support for technical assistance, troubleshooting, and software updates. 7. Target Market: * Professionals: Ideal for professionals in various industries, including journalists, researchers, students, and business professionals. * Outdoor Enthusiasts: Suitable for outdoor activities such as hiking, camping, and fieldwork where reliable transcription and note-taking are essential. * Everyday Users: Provides convenience and efficiency for everyday tasks, such as meetings, lectures, and personal reminders. 8. Conclusion: The Wearable AI Transcription Assistant sets a new standard for wearable technology, offering unmatched transcription and note-taking capabilities in a compact and durable package. With its advanced features, seamless connectivity, vibrant display, and user-friendly design, it is poised to revolutionize how we capture and manage information in our daily lives while adding a touch of personality and fun with customizable animations and expressions.

This is a BLE remote control Reference Design. It features a Microchip RN4871U BLE module for communication, various push buttons (Up, Down, Left, Right, OK) for control input, and a piezoelectric buzzer for audio feedback. Power is supplied by a battery and it is regulated to 3.3V for the BLE module. #BLE #IoT #referenceDesign #simple-embedded #microchip #template #reference-design

HVAC System controller board. Features 4 10A250VAC relays (For power control), a BME680 for environmental monitoring and a 5v-35v driver to control up to 2 DC motors. #esp32 #iot

This is a BLE remote control Reference Design. It features a Microchip RN4871U BLE module for communication, various push buttons (Up, Down, Left, Right, OK) for control input, and a piezoelectric buzzer for audio feedback. Power is supplied by a battery and it is regulated to 3.3V for the BLE module. #BLE #IoT #referenceDesign #simple-embedded #microchip #template #reference-design

I want to blow up a MOSFET gloriously. Basically supercapacitor onto MOSFET with a gate flipping setting.

Compact ACS712 current sensor module, capable of measuring up to 20A of AC or DC current. The layout includes a 2-pin connector for the input current, a terminal for the output voltage, and two capacitors for noise reduction. #template #project #sensor #current_sensor #ACS712

Autonomous irrigation system for up to 4 individual pots. It has an integrated humidity, pressure and temperature sensor, as well as 4 ports for soil moisture sensors. #esp32 #iot #matter

Two separate simulated circuits which demonstrate how step up and step down transformers work.

PWM-capable low-side MOSFET driver for controlling a 9 V LEGO motor from a Raspberry Pi 3.3 V GPIO signal, sized for up to 1.4 A stall/current peaks.

A simple fixed linear voltage regulator board that can provide 3.3V up to 1A output and could operate down to 1V input-to-output differential. #firstpcbFlux