This breakout board will solve all your power-monitoring problems. Instead of struggling with two multimeters, you can just use the handy INA219B chip on this breakout to both measure both the high side voltage and DC current draw over I2C with 1% precision. #Sublayout #CurrentSensor

Do not use this part

General Purpose Thick Film Standard Power and High-Power Chip Resistor 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film Features: - RMCF – standard power ratings - RMCP – high power ratings - Nickel barrier terminations standard - Power derating from 100% at 70ºC to zero at +155ºC - RoHS compliant, REACH compliant, and halogen free - AEC-Q200 compliant

Linear Voltage Regulator IC Positive Fixed 1 Output 600mA SOT-25 3.3V LDO AP2112K-3.3 The AP2112K-3.3TRG1 is a low dropout (LDO) linear voltage regulator designed to provide a stable 3.3V output from a higher input voltage. It is optimized for low noise, high power supply rejection ratio (PSRR), and low quiescent current, making it suitable for battery-powered and noise-sensitive applications. The device features current limiting and thermal shutdown protection, ensuring reliable operation under fault conditions. It is commonly used in portable electronics, RF modules, microcontroller power supplies, and other low-power systems. Key Features Fixed output voltage: 3.3V Output current: up to 600 mA Low dropout voltage: ~250 mV at 300 mA load High PSRR: up to 70 dB at 1 kHz Low quiescent current: typically 55 µA Stable with low ESR ceramic capacitors Built-in overcurrent protection Thermal shutdown protection Fast transient response Absolute Maximum Ratings Input Voltage (VIN): up to 6.5 V Output Current: Internally limited Operating Junction Temperature: -40°C to +125°C Storage Temperature: -65°C to +150°C Electrical Characteristics (Typical values unless otherwise specified) Output Voltage Accuracy: ±2% Dropout Voltage: 250 mV @ 300 mA 400 mV @ 600 mA Line Regulation: 0.05%/V Load Regulation: 0.2% Quiescent Current: 55 µA Shutdown Current: <1 µA PSRR: 70 dB @ 1 kHz 45 dB @ 10 kHz Pin Configuration (SOT-23-5 / SC-70-5) VIN – Input voltage GND – Ground EN – Enable (active high) NC – No connection VOUT – Regulated output (3.3V) Package Information Package Type: SOT-23-5 (TRG1 suffix indicates tape & reel) Mounting: Surface mount Small footprint suitable for compact PCB layouts Typical Applications Battery-powered devices Wireless modules (Wi-Fi, Bluetooth, RF) Microcontroller and FPGA power supplies Portable consumer electronics Sensor and analog circuits requiring low noise Compliance & Reliability RoHS compliant Lead-free package Designed for high reliability and long operational life #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LinearRegulator #VoltageRegulator

Red 631nm LED Indication - Discrete 2V 0603 (1608 Metric) The LTST-C190KRKT is a surface-mount red LED designed for compact electronic applications requiring reliable visual indication. It is housed in a standard chip LED package, making it suitable for automated assembly processes. This device offers high luminous intensity with low power consumption, ideal for status indicators, backlighting, and display applications. Key Features High brightness red LED Compact surface-mount package (0603 / 1608 metric) Low forward voltage and low power consumption Wide viewing angle for uniform illumination Compatible with automated placement equipment RoHS compliant and lead-free Electrical Characteristics (Typical @ 25°C) Forward Voltage (Vf): 2.0 V (typ), 2.4 V (max) Forward Current (If): 20 mA (recommended) Luminous Intensity: ~100–180 mcd Wavelength (Peak): ~631 nm (red) Optical Characteristics Color: Red Viewing Angle: 120° (typ) Absolute Maximum Ratings Forward Current: 30 mA (continuous) Peak Forward Current: 100 mA (pulse) Power Dissipation: ~75 mW Operating Temperature Range: -40°C to +85°C Storage Temperature Range: -40°C to +100°C Mechanical Characteristics Package Type: SMD Chip LED Package Size: 0603 (1.6 mm × 0.8 mm) Mounting Type: Surface Mount Lens Type: Clear Applications Status indicators in electronic devices Backlighting for displays and keypads Consumer electronics Industrial control panels Portable and battery-powered devices #commonpartslibrary #optoelectronic #led #red

Bipolar (BJT) Transistor NPN 40V 200 mA 300MHz 300 mW Surface Mount SOT-23-3 (TO-236) The MMBT3904LT1G is a general-purpose NPN bipolar junction transistor designed for switching and amplification applications. It is housed in a compact SOT-23 surface-mount package, making it suitable for high-density PCB designs. This transistor is widely used in low-power signal processing, digital switching, and analog amplification circuits due to its reliable performance and fast switching characteristics. Key Features General-purpose NPN transistor Compact SOT-23 surface-mount package Fast switching speed Low saturation voltage Suitable for low-current and low-power applications High reliability and stability Pb-free, Halogen-free, and RoHS compliant Electrical Characteristics (Typical @ 25°C unless otherwise specified) Collector-Emitter Voltage (VCEO): 40 V Collector-Base Voltage (VCBO): 60 V Emitter-Base Voltage (VEBO): 6 V Collector Current (IC): 200 mA (max) DC Current Gain (hFE): 100 – 300 Collector-Emitter Saturation Voltage (VCE(sat)): 0.2 V (typ) Transition Frequency (fT): ~300 MHz Absolute Maximum Ratings Collector Current (Continuous): 200 mA Power Dissipation: ~225 mW Junction Temperature: +150°C (max) Operating Temperature Range: -55°C to +150°C Storage Temperature Range: -55°C to +150°C Mechanical Characteristics Package Type: SOT-23 (TO-236AB) Mounting Type: Surface Mount Number of Pins: 3 Marking Code: Dependent on lot/manufacturer marking Applications General-purpose switching circuits Signal amplification Digital logic interfacing LED drivers and small load switching Audio and RF signal processing #CommonPartsLibrary #TransistorBJT #MMBT2222

The NE555 devices are precision timing circuits capable of producing accurate time delays or oscillation. In time-delay or monostable operating modes, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle are controlled independently with two external resistors and a single external capacitor. Each timer has a trigger level equal to approximately one-third of the supply voltage and a threshold level equal to approximately two-thirds of the supply voltage. These levels can be altered by use of the control voltage pin (CONT). When the trigger input (TRIG) is less than the trigger level, the flip-flop is set and the output goes high. If TRIG is greater than the trigger level and the threshold input (THRES) is greater than the threshold level, the flip-flop is reset and the output is low. The reset input (RESET) overrides all other inputs and is used to initiate a new timing cycle. If RESET is low, the flip-flop is reset and the output is low. Whenever the output is low, a lowimpedance path is provided between the discharge pin (DISCH) and the ground pin (GND). Tie all unused inputs to an appropriate logic level to prevent false triggering. The output circuit is capable of sinking or sourcing current up to 200mA. Operation is specified for supplies of 5V to 15V. With a 5V supply, output levels are compatible with TTL inputs. Features - Timing from microseconds to hours - Astable or monostable operation - Adjustable duty cycle - TTL-compatible output can sink or source up to 200mA - On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. Applications - Pulse-shaping circuits - Missing-pulse detectors - Pulse-width modulators - Pulse-position modulators - Sequential timers - Pulse generators -F requency dividers - Industrial controls

17V Clamp 5A (8/20µs) Ipp Tvs Diode Surface Mount SOT-666 The USBLC6-2SC6 and USBLC6-2P6 are monolithic application specific devices dedicated to ESD protection of high speed interfaces, such as USB 2.0, Ethernet links and video lines.

USB-C (USB TYPE-C) USB 3.2 Gen 2 (USB 3.1 Gen 2, Superspeed + (USB 3.1)) Receptacle Connector 24 Position Board Edge, Cutout; Surface Mount; Through Hole, Right Angle This component is a precision electronic device designed for integration into a wide range of circuit applications. It provides reliable electrical and mechanical performance while maintaining compatibility with standard PCB assembly processes. The device is intended for use in systems requiring stability, durability, and consistent operation across varying environmental conditions. Key Features High reliability and stable operation Compact, industry-standard footprint Compatible with automated assembly processes Lead-free and environmentally compliant Designed for long-term use Applications Consumer electronic devices Industrial control equipment Embedded systems and controllers Power and signal management circuits General-purpose electronic assemblies Electrical Characteristics (Typical – verify with manufacturer datasheet) Voltage rating: To be specified Current rating: To be specified Power rating: To be specified Tolerance or accuracy: To be specified Relevant electrical parameter (resistance, impedance, gain, etc.): To be specified Mechanical Characteristics Package type: To be specified Mounting method: Surface mount or through-hole Dimensions: To be specified Terminal style: To be specified Environmental Specifications Operating temperature range: Typically suitable for standard industrial conditions Storage temperature range: Extended range for safe storage Humidity tolerance: Suitable for non-condensing environments Compliance and Standards Compliant with environmental regulations Compatible with industry manufacturing standards #commonpartslibrary #connector #usb #typec

Slide Switch SPST 4A 125V Throuh Hole The L101011MS02Q is a single-pole, single-throw (SPST) miniature toggle switch designed for low-power switching applications. It features a compact panel-mount design with a durable actuator and reliable contact mechanism, making it suitable for control and signal switching in industrial, instrumentation, and consumer electronics. The switch provides a maintained (latching) ON-OFF function and is built for long mechanical and electrical life. Key Features SPST (Single Pole, Single Throw) configuration ON-OFF maintained switching function Miniature toggle actuator Panel mount design with threaded bushing Solder lug terminals for secure wiring High mechanical durability Compact form factor Mechanical Characteristics Mounting Type: Panel mount Actuator Type: Toggle lever Bushing Type: Threaded, with nut and washer Terminal Type: Solder lug Number of Poles: 1 Number of Throws: 1 Switching Function: ON-OFF (latching) Electrical Characteristics Rated Voltage: 125 VAC / 28 VDC Rated Current: 3 A @ 125 VAC, 6 A @ 28 VDC Contact Resistance: ≤ 20 mΩ (initial) Insulation Resistance: ≥ 1,000 MΩ Dielectric Strength: 1,000 VAC for 1 minute Material Specifications Housing: Thermoplastic or phenolic (manufacturer dependent) Actuator: Metal (nickel-plated brass) Contacts: Copper alloy with silver plating Terminals: Brass, tin-plated Environmental Specifications Operating Temperature Range: -30°C to +85°C Storage Temperature: -40°C to +85°C Mechanical Life Mechanical Life: ≥ 40,000 cycles Electrical Life: ≥ 10,000 cycles (at rated load) Typical Applications Control panels Power switching for small devices Instrumentation equipment Audio equipment Industrial and consumer electronics #commonpartslibrary #rocker #switch #spst

USB-C (USB TYPE-C) USB 2.0 Receptacle Connector 24 (16+8 Dummy) Position Surface Mount, Right Angle; Through Hole USB Type-C receptacle 16 pin USB2.0 The USB4215-03-A is a USB Type-C receptacle connector designed for USB 2.0 applications. It features a 16-pin configuration supporting reversible plug orientation with standard USB 2.0 differential data lines and configuration channel (CC) pins. The connector is intended for surface-mount PCB assembly with through-hole shell stakes for enhanced mechanical strength. It is widely used in compact embedded systems for power delivery, charging interfaces, and basic data communication. Key Features USB Type-C receptacle (USB 2.0 compliant) 16 functional pins (no SuperSpeed support) Reversible plug orientation Surface-mount contacts with through-hole shell tabs Compact, low-profile design High insertion cycle durability Suitable for automated assembly Electrical Characteristics Rated Current: VBUS: up to 5.0 A (depending on PCB design and cable) Signal pins: 0.25 A max Rated Voltage: 20 V DC max Contact Resistance: ≤ 40 mΩ Insulation Resistance: ≥ 100 MΩ Dielectric Withstanding Voltage: 100 V AC Mechanical Characteristics Mounting Type: Surface Mount (SMT) with Through-Hole Shield Tabs Number of Positions: 16 Mating Cycles: 10,000 cycles (typical) Insertion Force: 5–20 N Extraction Force: 8–20 N Material Specifications Contacts: Copper Alloy Contact Plating: Gold over Nickel Housing: High-temperature thermoplastic (UL94V-0) Shell: Stainless Steel Environmental Characteristics Operating Temperature Range: -25°C to +85°C Storage Temperature Range: -40°C to +85°C RoHS Compliant: Yes Halogen Free: Yes Pin Configuration (USB 2.0 Type-C) VBUS (Power) GND (Ground) D+ / D− (USB 2.0 differential pair) CC1 / CC2 (Configuration channel) SBU pins (optional/unused in USB 2.0 designs) Applications USB power input (5 V / USB-C PD trigger designs) Embedded systems and development boards Consumer electronics Charging interfaces Low-speed USB communication devices Packaging Tape & Reel for automated pick-and-place assembly Compliance & Standards USB Type-C Specification (USB 2.0 interface) RoHS / REACH compliant UL recognized materials #CommonPartsLibrary #Connector #USB-C

PTS 810 Series Microminiature SMT Top Actuated Features/Benefits - 4.2 x 3.2 mm footprint - 2.5 mm thickness - High number of cycles - Color coded actuators Typical Applications - Control panels - Nomad devices - Remote controls - Keyless entry system 3.2mm 2.5mm Round Button 50mA Brick nogging 4.2mm SPST 16V SMD Tactile Switch SPST-NO Top Actuated Surface Mount.

555 Type, Timer/Oscillator (Single) IC 100kHz 8-PDIP NE555 DIP-8 through hole The NE555P is a classic and widely used precision timer IC manufactured by companies like Texas Instruments and others. It belongs to the popular 555 timer family and is designed for generating accurate time delays, oscillations, and pulse signals. The “P” variant refers to the PDIP (Plastic Dual In-line Package), making it ideal for through-hole mounting, breadboarding, and prototyping. NE555P PDIP-8 timer Internally, the NE555P consists of: Two comparators A flip-flop A discharge transistor A voltage divider network These blocks allow flexible configuration for timing and waveform generation. Key Features Timing & Operation Modes Monostable mode (one-shot pulse generation) Astable mode (continuous oscillator) Bistable mode (flip-flop operation) Electrical Characteristics Supply voltage range: 4.5V to 16V Output can source or sink up to 200 mA Adjustable duty cycle Performance High timing accuracy and stability Timing range from microseconds to hours (depends on external R and C) Temperature-stable operation Package & Usability 8-pin DIP (through-hole) package Easy to use for: Breadboards DIY electronics Educational projects Common Applications LED flashers and blinkers Pulse generation Time delay circuits PWM control (e.g., dimming LEDs, motor speed control) Tone/sound generation #Timer #commonpartslibrary

Green LED Indication - Discrete 2.2V 0603 (1608 Metric) The SML-LX0603GW-TR is a surface-mount white LED in a compact 0603 (1608 metric) package, designed for indicator and backlighting applications. It offers high brightness with low power consumption and wide viewing angle, making it suitable for portable and space-constrained electronic devices. The device is optimized for automated assembly and is supplied in tape-and-reel packaging. Key Features White LED (cool white emission) Compact 0603 (1.6 mm × 0.8 mm) SMD package High luminous intensity with low forward current Wide viewing angle (~120° typical) Low power consumption Compatible with reflow soldering Tape & reel packaging for automated assembly Optical Characteristics (Typical values) Emission Color: White Luminous Intensity: ~100 to 300 mcd @ 20 mA Color Temperature: ~6000K to 8000K Viewing Angle: 120° Electrical Characteristics (Typical values unless otherwise specified) Forward Voltage (VF): Typ: 3.0 V Max: 3.4 V @ 20 mA Forward Current (IF): 20 mA (continuous) Reverse Voltage (VR): 5 V Power Dissipation: ~75 mW Absolute Maximum Ratings Forward Current: 25 mA (continuous) Peak Forward Current: 100 mA (pulse, short duration) Operating Temperature: -40°C to +85°C Storage Temperature: -40°C to +100°C Mechanical Characteristics Package Type: 0603 (1608 metric) Dimensions: ~1.6 mm × 0.8 mm × 0.8 mm Mounting Type: Surface mount (SMT) Polarity: Cathode marking on package Material Specifications Lens: Epoxy resin (diffused) LED Chip: InGaN (Indium Gallium Nitride) Lead Frame: Copper alloy with silver plating Packaging Information Packaging Type: Tape & Reel (TR) Reel Quantity: Typically 3,000–5,000 pcs per reel RoHS Compliant: Yes Lead-Free: Yes Typical Applications Status indicators Backlighting (LCD, keypad, buttons) Consumer electronics Portable devices Automotive interior lighting (low-power) #commonpartslibrary #optoelectronic #led #SML-LX0603

Humidity, Temperature 0 ~ 100% RH I2C ±2% RH 8 s Surface Mount The SHTC3-TR-2.5KS is a digital humidity and temperature sensor from Sensirion, designed for high accuracy, low power consumption, and compact integration. It utilizes a fully calibrated capacitive humidity sensor and bandgap temperature sensor, providing precise environmental measurements via an I²C interface. The device is optimized for battery-powered and space-constrained applications, featuring ultra-low power consumption and sleep modes, making it ideal for IoT, wearable, and mobile devices. Key Features Relative humidity and temperature sensing in a single package Fully calibrated and linearized digital output I²C interface (up to 1 MHz fast mode) Ultra-low power consumption with sleep mode High accuracy and fast response time Small DFN package for compact designs Factory calibrated, no external calibration required Mechanical Characteristics Package Type: DFN (Dual Flat No-Lead) Package Size: ~2.0 mm × 2.0 mm × 0.75 mm Mounting Type: Surface mount (SMT) Terminals: Bottom pads Electrical Characteristics Supply Voltage (VDD): 1.62 V to 3.6 V Average Supply Current: Measurement: ~170 µA Sleep Mode: ~0.3 µA Interface: I²C (address selectable) Output: Digital (temperature and relative humidity) Sensing Performance Humidity Range: 0 to 100 %RH Humidity Accuracy: ±2 %RH (typical) Temperature Range: -40°C to +125°C Temperature Accuracy: ±0.2°C (typical) Response Time (τ63%): ~8 seconds (humidity) Functional Features Low-power measurement modes (normal and low power) Sleep mode for minimal energy consumption CRC checksum for data integrity Clock stretching support (optional) Environmental Specifications Operating Temperature Range: -40°C to +125°C Storage Temperature Range: -40°C to +125°C Packaging Information Packaging Type: Tape & Reel (TR) Reel Quantity: 2,500 units (2.5KS) Lead-Free / RoHS compliant Typical Applications Wearable devices Smartphones and mobile electronics IoT sensors and nodes Smart home devices (thermostats, air quality monitors) HVAC systems Environmental monitoring #CommonPartsLibrary #Sensor #Transducer #Humidity #Moisture-Sensor

JST PH Connector Header Through Hole 3 position 0.079" (2.00mm) The B3B-PH-K-S(LF)(SN) is a 3-position, 2.0 mm pitch, through-hole (THT) male header from the JST PH series, designed for wire-to-board connections. It is a top-entry, shrouded connector that mates with JST PH crimp housings, commonly used for compact internal wiring in electronic devices such as consumer electronics, battery connections, and embedded systems. This connector is optimized for high-density PCB layouts, offering a reliable and secure connection with a locking mechanism and low contact resistance. Key Features Mechanical 3 positions (3-pin) 2.0 mm pitch (compact spacing) Through-hole mounting (THT) Top-entry / vertical orientation Shrouded header (prevents misalignment) Detent lock / friction lock for secure mating Electrical Rated current: up to 2A per pin Rated voltage: up to 100V AC/DC Low contact resistance (~10 mΩ max initial) High insulation resistance (≥1000 MΩ) Environmental Operating temperature: -25°C to +85°C Design & Reliability Fully shrouded design → protects pins and ensures proper insertion Reliable contact structure with dimpled contacts for stable connection PCB retention mechanism → improves mechanical stability Tin-plated contacts for good conductivity and solderability Application Use Commonly used for: Battery connectors Sensor modules Embedded systems (e.g., microcontroller boards) Consumer electronics internal wiring Power + signal low-current connections #commonpartslibrary #connector #header #tht

MAX98357A Series 5.5V 3.2W PCM Input Class D Audio Power Amplifier - TQFN-16 The MAX98357A/MAX98357B is an easy-to-use, low-cost, digital pulse-code modulation (PCM) input Class D amplifier that provides industry-leading Class AB audio performance with Class D efficiency. The digital audio interface automatically recognizes up to 35 different PCM and TDM clocking schemes which eliminates the need for I2C programming. Operation is further simplified by eliminating the need for an external MCLK signal that is typically used for PCM communication. Simply supply power, LRCLK, BCLK, and digital audio to generate audio! Furthermore, a novel pinout allows customers to use the cost-effective WLP package with no need for expensive vias (refer to Application Note 6643: Optimize Cost, Size, and Performance with MAX98357 WLP for more information). The digital audio interface is highly flexible with the MAX98357A supporting I2S data and the MAX98357B supporting left-justified data. Both ICs support 8 channel time division multiplexed (TDM) data. The digital audio interface accepts specified sample rates between 8kHz and 96kHz for all supported data formats. The ICs can be configured to produce a left channel, right channel, or (left/2 + right/2) output from the stereo input data. The ICs operate using 16/24/32-bit data for I2S and left-justified modes as well as 16-bit or 32-bit data using TDM mode. The ICs eliminate the need for the external MCLK signal that is typically used for PCM communication. This reduces EMI and possible board coupling issues in addition to reducing the size and pin count of the ICs. The ICs also feature a very high wideband jitter tolerance (12ns typ) on BCLK and LRCLK to provide robust operation. Active emissions-limiting, edge-rate limiting, and overshoot control circuitry greatly reduce EMI. A filterless spread-spectrum modulation scheme eliminates the need for output filtering found in traditional Class D devices and reduces the component count of the solution. The ICs are available in 9-pin WLP (1.345mm x 1.435mm x 0.64mm) and 16-pin TQFN (3mm x 3mm x 0.75mm) packages and are specified over the -40°C to +85°C temperature range. ● Single-Supply Operation (2.5V to 5.5V) ● 3.2W Output Power into 4Ω at 5V ● 2.4mA Quiescent Current ● 92% Efficiency (RL = 8Ω, POUT = 1W) ● 22.8μVRMS Output Noise (AV = 15dB) ● Low 0.013% THD+N at 1kHz ● No MCLK Required ● Sample Rates of 8kHz to 96kHz ● Supports Left, Right, or (Left/2 + Right/2) Output ● Sophisticated Edge Rate Control Enables Filterless Class D Outputs ● 77dB PSRR at 1kHz ● Low RF Susceptibility Rejects TDMA Noise from GSM Radios ● Extensive Click-and-Pop Reduction Circuitry ● Robust Short-Circuit and Thermal Protection ● Available in Space-Saving Packages: 1.345mm x 1.435mm WLP (0.4mm Pitch) and 3mm x 3mm TQFN ● Solution Size with Single Bypass Capacitor is 4.32mm2 Applications ● Single Li-ion Cell/5V Devices ● Smart Speakers ● Notebook Computers ● IoT Devices ● Gaming Devices (Audio and Haptics) ● Smartphones ● Tablets ● Cameras #commonpartslibrary #integratedcircuit #linearamplifier #mono

Tactile Switch SPST-NO Top Actuated Surface Mount The B3FS-1002P is a compact, surface-mount tactile switch designed for low-profile input applications. It provides a momentary contact mechanism with a distinct tactile feedback, making it suitable for user interface controls in consumer electronics, industrial devices, and compact embedded systems. The switch features a sealed construction for improved reliability and is optimized for automated PCB assembly processes. Mechanical Characteristics Mounting Type: Surface Mount (SMD) Actuator Style: Top push Actuator Height: Low profile Outline: Rectangular compact body Terminal Type: Gull-wing terminals Sealing: Dust-resistant (sealed construction) Electrical Characteristics Switch Type: Single Pole Single Throw (SPST) Contact Configuration: Normally Open (NO) Rated Voltage: Low voltage DC applications Rated Current: Suitable for signal-level switching Contact Resistance: Low initial contact resistance Insulation Resistance: High insulation resistance between terminals Operating Characteristics Operating Force: Standard tactile force (manufacturer-defined variant) Travel Distance: Short stroke tactile action Operating Life: High durability for repeated actuation cycles Bounce Time: Minimal contact bounce for reliable switching Environmental Characteristics Operating Temperature Range: Wide operating range suitable for consumer and industrial use Storage Temperature Range: Standard electronic component storage conditions Humidity Resistance: Designed to withstand typical ambient humidity conditions Material & Construction Actuator Material: High-strength polymer Housing Material: Heat-resistant plastic Contact Material: Metal alloy with surface plating for durability Terminal Finish: Solderable finish compatible with reflow soldering Packaging Information Packaging Type: Tape and reel Assembly Compatibility: Fully compatible with automated pick-and-place and reflow processes Applications Consumer electronics (keypads, remote controls) Industrial control panels Portable devices Embedded system user interfaces Wearable and compact electronics #commonpartslibrary #switch #tactile

PIC PIC® 16F Microcontroller IC 8-Bit 20MHz 14KB (8K x 14) FLASH 40-PDIP The PIC16F877A-I/P is a high-performance 8-bit microcontroller from Microchip Technology, based on a Harvard architecture with separate program and data memory buses. It is designed for a wide range of embedded applications requiring reliable processing, multiple communication interfaces, and analog capability. The device integrates Flash program memory, EEPROM data storage, and numerous peripherals including ADC, timers, serial communication modules, and PWM functions. Packaged in a 40-pin PDIP form factor, it is widely used in industrial automation, consumer electronics, and educational development systems. Core Features 8-bit PIC microcontroller architecture Harvard architecture with RISC instruction set Operating frequency up to 20 MHz Single-cycle instruction execution (except branches) Memory Program Memory: 8K words (Flash) Data Memory (RAM): 368 bytes EEPROM Data Memory: 256 bytes I/O Features Up to 33 programmable I/O pins Multiple input/output ports (PORTA, PORTB, PORTC, PORTD, PORTE) High current sink/source capability on selected pins Analog Features 10-bit Analog-to-Digital Converter (ADC) Up to 8 analog input channels Programmable voltage reference Timers and Control Three timers (Timer0, Timer1, Timer2) Capture/Compare/PWM (CCP) modules Watchdog Timer (WDT) Power-on Reset (POR) and Brown-out Reset (BOR) Communication Interfaces USART (Universal Synchronous/Asynchronous Receiver/Transmitter) SPI (Serial Peripheral Interface) I²C (Inter-Integrated Circuit) via MSSP module Electrical Characteristics Operating Voltage: 4.0V to 5.5V Operating Temperature Range: -40°C to +85°C (Industrial grade) Low power consumption modes available Package Information Package Type: PDIP (Plastic Dual Inline Package) Pin Count: 40 pins Mounting Type: Through-hole Applications Industrial control systems Embedded automation Consumer electronics Sensor interfacing and data acquisition Educational and prototyping platforms #commonpartslibrary #integratedcircuit #microcontroller

600 Ohms @ 100 MHz 1 Ferrite Bead 0603 (1608 Metric) ferrite bead 600 ohm 0603 ferrite bead 600 ohm 100MHz 0603 ferrite bead 0603 600ohm The BLM18AG601SN1D is a surface-mount ferrite bead designed for suppression of high-frequency noise in electronic circuits. It provides high impedance at high frequencies while maintaining low DC resistance, making it suitable for power lines and signal line filtering. This component is commonly used in portable electronics, communication devices, and general digital circuits to improve EMI performance. ELECTRICAL CHARACTERISTICS Impedance: 600 Ω ±25% @ 100 MHz Rated Current: 500 mA (max) DC Resistance (DCR): 0.5 Ω (typ), 0.8 Ω (max) Insulation Resistance: 10 MΩ min PHYSICAL CHARACTERISTICS Package Size: 0603 (1608 Metric) Length: 1.6 mm Width: 0.8 mm Height: 0.8 mm (typ) Mounting Type: Surface Mount (SMD) ENVIRONMENTAL & OPERATING CONDITIONS Operating Temperature Range: -55°C to +125°C Storage Temperature Range: -55°C to +125°C APPLICATIONS Power supply line noise suppression Signal line EMI filtering Mobile devices and handheld electronics Computers and peripherals Consumer electronics FEATURES High impedance at high frequencies for effective noise suppression Low DC resistance minimizes signal/power loss Compact 0603 package suitable for high-density PCB layouts Reliable multilayer construction Lead-free and RoHS compliant PACKAGING Packaging Type: Tape and Reel Standard Reel Quantity: Typically 4000 pcs/reel #CommonPartLibrary #Filter #FerriteBead

Buck Switching Regulator IC Positive Fixed 5V 1 Output 1A SOT-23-6 The LMR50410Y5FQDBVRQ1 (part of the LMR50410-Q1 family from Texas Instruments) is a synchronous step-down (buck) DC-DC converter designed for automotive and industrial power applications. It operates over a wide input voltage range of 4 V to 36 V and can deliver up to 1 A output current, making it suitable for converting higher, unregulated voltages into stable lower voltages (e.g., 5 V or 3.3 V rails). The device integrates power switches, control circuitry, and compensation internally, allowing simple design with minimal external components and a compact PCB footprint. Key Features Power & Performance Wide input voltage range: 4 V to 36 V Output current: up to 1 A High switching frequency: 2.1 MHz (enables small inductors) High efficiency with PFM (light load) and FPWM (constant frequency) options Integration & Ease of Use Synchronous rectification (integrated high-side & low-side MOSFETs) Internal compensation (no complex external tuning) Minimal external components required Small SOT-23-6 package for compact designs Protection & Reliability Cycle-by-cycle current limit Short-circuit protection (hiccup mode) Thermal shutdown protection Undervoltage lockout (UVLO) ±1% reference voltage accuracy Automotive & Industrial Capability AEC-Q100 qualified (automotive grade) Operating temperature: Ambient: up to 125°C Junction: up to 150°C Designed for rugged automotive environments Additional Features Soft-start for controlled startup Precision enable pin for system control Monotonic startup with pre-biased output Available in fixed output (e.g., 5 V) variants Typical Applications Automotive electronics (ADAS, infotainment, lighting) Industrial power supplies Distributed power systems General-purpose DC-DC regulation #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

Board Mount Humidity Sensors Intermediate Humidity and Temperature Sensor Humidity, Temperature 0 ~ 100% RH I2C ±1.8% RH 4 s Surface Mount The SHT41-AD1B-R2 is a fully calibrated, low-power environmental sensor that measures relative humidity (RH) and temperature. It integrates sensing elements, signal processing, and a digital interface into a small surface-mount package, making it ideal for space-constrained designs. Key Features Sensor Type: Digital humidity and temperature sensor Interface: I²C (easy MCU integration) Supply Voltage: ~1.08 V to 3.6 V Humidity Accuracy: up to ±1.8% RH (typical) Temperature Accuracy: up to ±0.2 °C (typical) Response Time: Fast measurement and low latency Power Consumption: Ultra-low, suitable for battery devices Package: DFN (compact, ~1.5 × 1.5 mm) Factory Calibration: No external calibration required Functional Overview The sensor uses capacitive humidity sensing combined with a bandgap temperature sensor. Internal electronics convert these measurements into digital data via I²C, eliminating the need for external ADCs or complex signal conditioning. Design Advantages Small footprint for compact PCBs Low power consumption for IoT and portable devices High reliability with long-term stability Fast response time for real-time monitoring Simple integration with microcontrollers Typical Applications IoT and smart home devices HVAC and climate control systems Wearables and portable electronics Industrial monitoring systems Environmental data logging #CommonPartsLibrary #Sensors,-Transducer #Humidity #Moisture-Sensor #SHT4x

LED Circuit Board Indicator LED Circuit Board Indicator 2 High Red (x 1), Yellow (x 1) Diffused, Tinted 1.7V Red, 1.85V Yellow 30mA Red, 30mA Yellow Round with Domed Top 2.90mm Dia Through Hole, Right Angle #Optoelectronics #LED #LightBars #BarGraphs

Connector Header Through Hole 6 position 0.100" Pin Header 1x06 2.54mm PinHeader 1x6 2.54mm The TSW-106-07-G-S is a through-hole vertical header designed for board-to-board and board-to-wire interconnection in electronic systems. It is part of a precision connector series known for high reliability, consistent mechanical alignment, and excellent electrical performance. The component is commonly used in applications requiring modular connectivity, prototyping flexibility, and secure signal routing between printed circuit boards or peripheral interfaces. Its design supports repeated mating cycles while maintaining stable contact integrity, making it suitable for both development and production environments. Functional Description This component functions as a single-row header that provides a direct electrical interface between a printed circuit board and a mating connector or cable assembly. It enables straightforward signal or power routing through plated pins that are soldered into the PCB. The vertical orientation allows perpendicular mating, supporting compact and efficient board layouts. The connector is designed to ensure proper alignment and retention during mating, reducing the risk of intermittent connections. Electrical Characteristics The header supports low-voltage signal transmission and moderate current levels typical of board-level interconnects. It offers low contact resistance to maintain signal integrity and efficient current flow. The contact system is designed to provide consistent electrical performance across repeated insertions, ensuring reliability in both signal and power applications. Mechanical Characteristics The component features a robust insulating housing that maintains pin alignment and structural integrity during handling and operation. The contact pins are fabricated from conductive material and plated to enhance durability, conductivity, and مقاومت to corrosion. The through-hole mounting style provides strong mechanical anchoring to the printed circuit board, improving resistance to mechanical stress and vibration. The design supports reliable mating with compatible connectors and ensures long service life. Environmental Characteristics The TSW-106-07-G-S is constructed using materials that provide stable performance under typical environmental conditions encountered in electronic assemblies. It is designed to withstand standard temperature ranges and environmental stresses such as humidity and mechanical handling, maintaining electrical and mechanical reliability over time. Applications This header is widely used in embedded systems, industrial electronics, development platforms, communication equipment, and general-purpose PCB interconnect applications. It is especially suited for designs requiring modular connectivity, easy assembly, and dependable signal transfer. Summary The TSW-106-07-G-S from Samtec is a reliable through-hole header solution that combines mechanical durability with stable electrical performance. Its straightforward design, compatibility with standard interconnect systems, and suitability for a wide range of applications make it a common choice for board-level connectivity in modern electronic designs. #CommonPartsLibrary #Connector #Header #TSW

2 Position Board Side/Socket - Closed 5.08mm Pitch Right-Angle Pin The WJ2EDGRC-5.08-02P-14-00A is a 2-position pluggable terminal block (screw-type connector) with a 5.08 mm pitch, commonly used for PCB power and signal connections. It is part of the EDGRC series designed for reliable wire-to-board connectivity in industrial, automation, and power electronics applications. It allows secure cable termination using screw clamps and is designed for easy plug-in/out mating with a corresponding header on a PCB. Key Features Type: Pluggable terminal block (female plug) Pin count: 2 positions Pitch: 5.08 mm Connection method: Screw clamp / rising cage clamp Mounting style: Through-hole (mates with PCB header) Wire termination: Suitable for solid and stranded wires High reliability contact design for stable electrical connection Detachable plug-in design for easy maintenance and replacement High current capability (typical for 5.08 mm pitch terminal blocks) Industrial-grade insulation material for durability and safety Wide usage: Power supply input, motor control, industrial I/O, and general PCB wiring #CommonPartsLibrary #Connector #Terminal block