External Flash Module #Module The External Flash Module is a compact, high-performance circuit designed around a 128Mbit NOR flash memory, ensuring fast and reliable data storage for modern embedded systems. Integrated with precision passive components and optimized connectivity, this module offers efficient power management and seamless integration for diverse applications in IoT, industrial automation, and consumer electronics. #ExternalFlashModule #NORFlash #EmbeddedSystems #IoT #DataStorage #ElectronicsDesign

Module with external GND

Low power long range transceiver module, SPI and parallel interface, 868 MHz, spreading factor 6 to12, bandwith 7.8 to 500kHz, -111 to -139 dBm, SMD-16, DIP-16

An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.

ARM® Cortex®-M0+ - Microcontroller IC 32-Bit Dual-Core 133MHz External Program Memory 56-QFN (7x7) Alternative MPN #SC0914(7) #SC0914(13) #RaspberryPi #Raspberry #Pi #RPi #Pico

Addressable RGB LEDs 3.2x2.8x1.78 mm 0.2W Intelligent external control surface mount SMD LED #CommonPartsLibrary #LED #Addressable

The NE555 devices are precision timing circuits capable of producing accurate time delays or oscillation. In time-delay or monostable operating modes, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle are controlled independently with two external resistors and a single external capacitor. Each timer has a trigger level equal to approximately one-third of the supply voltage and a threshold level equal to approximately two-thirds of the supply voltage. These levels can be altered by use of the control voltage pin (CONT). When the trigger input (TRIG) is less than the trigger level, the flip-flop is set and the output goes high. If TRIG is greater than the trigger level and the threshold input (THRES) is greater than the threshold level, the flip-flop is reset and the output is low. The reset input (RESET) overrides all other inputs and is used to initiate a new timing cycle. If RESET is low, the flip-flop is reset and the output is low. Whenever the output is low, a lowimpedance path is provided between the discharge pin (DISCH) and the ground pin (GND). Tie all unused inputs to an appropriate logic level to prevent false triggering. The output circuit is capable of sinking or sourcing current up to 200mA. Operation is specified for supplies of 5V to 15V. With a 5V supply, output levels are compatible with TTL inputs. Features - Timing from microseconds to hours - Astable or monostable operation - Adjustable duty cycle - TTL-compatible output can sink or source up to 200mA - On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. Applications - Pulse-shaping circuits - Missing-pulse detectors - Pulse-width modulators - Pulse-position modulators - Sequential timers - Pulse generators -F requency dividers - Industrial controls

2 Position Terminal Block Header, Male Pins, Shrouded (4 Side) 0.200" (5.08mm) 90°, Right Angle Through Hole Phoenix Contact MSTBA 2.5/ 2-G-5.08 CAN connector terminal block 2 pin The component is a two-position pluggable terminal block header designed for secure and reliable wire-to-board connections in industrial and embedded electronic systems. It is part of the COMBICON MSTB family, widely used for field wiring applications such as CAN bus, RS485, and power distribution. The device provides a robust interface between PCB circuitry and external wiring, supporting easy installation, maintenance, and replacement through a pluggable connection system. Mechanical Characteristics Number of Positions: 2 Pitch: 5.08 mm Mounting Type: Through-hole PCB mount Orientation: Vertical (straight) Termination Style: Pin header for mating plug connector Housing Material: Polyamide (PA), high-temperature resistant Color: Green Electrical Characteristics Rated Voltage: Up to 250 V Rated Current: Up to 12 A Contact Material: Copper alloy Contact Plating: Tin plated Environmental Characteristics Operating Temperature Range: -40°C to +105°C Flammability Rating: UL94 V-0 Mating and Compatibility Compatible Plug Series: Phoenix Contact MSTB 2,5 series (e.g., 1757019) Connection Method (Plug Side): Screw clamp termination Wire Size Range: Typically accepts 24 AWG to 12 AWG (depending on mating plug) Standards and Compliance RoHS: Compliant UL Recognized: Yes IEC Compliance: Yes Application Notes The component is commonly used in industrial communication systems such as CAN bus networks where a reliable and removable connection is required for CANH and CANL signals. Its 5.08 mm pitch ensures adequate spacing for signal integrity and ease of wiring, while the pluggable design simplifies field servicing and module replacement. #connector #tht #terminalblock

555 Type, Timer/Oscillator (Single) IC 100kHz 8-PDIP NE555 DIP-8 through hole The NE555P is a classic and widely used precision timer IC manufactured by companies like Texas Instruments and others. It belongs to the popular 555 timer family and is designed for generating accurate time delays, oscillations, and pulse signals. The “P” variant refers to the PDIP (Plastic Dual In-line Package), making it ideal for through-hole mounting, breadboarding, and prototyping. NE555P PDIP-8 timer Internally, the NE555P consists of: Two comparators A flip-flop A discharge transistor A voltage divider network These blocks allow flexible configuration for timing and waveform generation. Key Features Timing & Operation Modes Monostable mode (one-shot pulse generation) Astable mode (continuous oscillator) Bistable mode (flip-flop operation) Electrical Characteristics Supply voltage range: 4.5V to 16V Output can source or sink up to 200 mA Adjustable duty cycle Performance High timing accuracy and stability Timing range from microseconds to hours (depends on external R and C) Temperature-stable operation Package & Usability 8-pin DIP (through-hole) package Easy to use for: Breadboards DIY electronics Educational projects Common Applications LED flashers and blinkers Pulse generation Time delay circuits PWM control (e.g., dimming LEDs, motor speed control) Tone/sound generation #Timer #commonpartslibrary

Humidity, Temperature 0 ~ 100% RH I2C ±2% RH 8 s Surface Mount The SHTC3-TR-2.5KS is a digital humidity and temperature sensor from Sensirion, designed for high accuracy, low power consumption, and compact integration. It utilizes a fully calibrated capacitive humidity sensor and bandgap temperature sensor, providing precise environmental measurements via an I²C interface. The device is optimized for battery-powered and space-constrained applications, featuring ultra-low power consumption and sleep modes, making it ideal for IoT, wearable, and mobile devices. Key Features Relative humidity and temperature sensing in a single package Fully calibrated and linearized digital output I²C interface (up to 1 MHz fast mode) Ultra-low power consumption with sleep mode High accuracy and fast response time Small DFN package for compact designs Factory calibrated, no external calibration required Mechanical Characteristics Package Type: DFN (Dual Flat No-Lead) Package Size: ~2.0 mm × 2.0 mm × 0.75 mm Mounting Type: Surface mount (SMT) Terminals: Bottom pads Electrical Characteristics Supply Voltage (VDD): 1.62 V to 3.6 V Average Supply Current: Measurement: ~170 µA Sleep Mode: ~0.3 µA Interface: I²C (address selectable) Output: Digital (temperature and relative humidity) Sensing Performance Humidity Range: 0 to 100 %RH Humidity Accuracy: ±2 %RH (typical) Temperature Range: -40°C to +125°C Temperature Accuracy: ±0.2°C (typical) Response Time (τ63%): ~8 seconds (humidity) Functional Features Low-power measurement modes (normal and low power) Sleep mode for minimal energy consumption CRC checksum for data integrity Clock stretching support (optional) Environmental Specifications Operating Temperature Range: -40°C to +125°C Storage Temperature Range: -40°C to +125°C Packaging Information Packaging Type: Tape & Reel (TR) Reel Quantity: 2,500 units (2.5KS) Lead-Free / RoHS compliant Typical Applications Wearable devices Smartphones and mobile electronics IoT sensors and nodes Smart home devices (thermostats, air quality monitors) HVAC systems Environmental monitoring #CommonPartsLibrary #Sensor #Transducer #Humidity #Moisture-Sensor

RP2040 chip for Raspberry Pi Pico - ARM® Cortex®-M0+ MCU 32-Bit The RP2040 is a high-performance, low-cost microcontroller built around two ARM Cortex-M0+ cores. It is optimized for flexibility, ease of use, and deterministic real-time performance. Unlike many microcontrollers, it includes a unique programmable I/O subsystem (PIO), allowing custom hardware interfaces without extra components. Key Features Processing Dual-core ARM Cortex-M0+ processors Up to 133 MHz clock speed Efficient integer performance with low power consumption Memory 264 KB on-chip SRAM External QSPI flash support (typically 2 MB–16 MB depending on board) Programmable I/O (PIO) 2 PIO blocks, each with 4 state machines Enables custom protocols (e.g., SPI, I2C, UART, WS2812, VGA, etc.) Offloads timing-critical tasks from CPU 🔗 Connectivity Interfaces 2× UART 2× SPI 2× I2C USB 1.1 controller (device or host support) 16× PWM channels Analog Features 12-bit ADC (up to 5 channels, including internal temperature sensor) Power & Voltage Operating voltage: 1.8V – 3.3V Low-power modes available Package Options QFN-56 (7×7 mm) Development Ecosystem Supports C/C++ SDK MicroPython and CircuitPython support Strong community and documentation Typical Applications Embedded systems and IoT devices Robotics and automation DIY electronics and prototyping USB devices (HID, MIDI, etc.) Custom communication interfaces using PIO #CommonPartsLibrary #IntegratedCircuit #Microcontroller

MAX98357A Series 5.5V 3.2W PCM Input Class D Audio Power Amplifier - TQFN-16 The MAX98357A/MAX98357B is an easy-to-use, low-cost, digital pulse-code modulation (PCM) input Class D amplifier that provides industry-leading Class AB audio performance with Class D efficiency. The digital audio interface automatically recognizes up to 35 different PCM and TDM clocking schemes which eliminates the need for I2C programming. Operation is further simplified by eliminating the need for an external MCLK signal that is typically used for PCM communication. Simply supply power, LRCLK, BCLK, and digital audio to generate audio! Furthermore, a novel pinout allows customers to use the cost-effective WLP package with no need for expensive vias (refer to Application Note 6643: Optimize Cost, Size, and Performance with MAX98357 WLP for more information). The digital audio interface is highly flexible with the MAX98357A supporting I2S data and the MAX98357B supporting left-justified data. Both ICs support 8 channel time division multiplexed (TDM) data. The digital audio interface accepts specified sample rates between 8kHz and 96kHz for all supported data formats. The ICs can be configured to produce a left channel, right channel, or (left/2 + right/2) output from the stereo input data. The ICs operate using 16/24/32-bit data for I2S and left-justified modes as well as 16-bit or 32-bit data using TDM mode. The ICs eliminate the need for the external MCLK signal that is typically used for PCM communication. This reduces EMI and possible board coupling issues in addition to reducing the size and pin count of the ICs. The ICs also feature a very high wideband jitter tolerance (12ns typ) on BCLK and LRCLK to provide robust operation. Active emissions-limiting, edge-rate limiting, and overshoot control circuitry greatly reduce EMI. A filterless spread-spectrum modulation scheme eliminates the need for output filtering found in traditional Class D devices and reduces the component count of the solution. The ICs are available in 9-pin WLP (1.345mm x 1.435mm x 0.64mm) and 16-pin TQFN (3mm x 3mm x 0.75mm) packages and are specified over the -40°C to +85°C temperature range. ● Single-Supply Operation (2.5V to 5.5V) ● 3.2W Output Power into 4Ω at 5V ● 2.4mA Quiescent Current ● 92% Efficiency (RL = 8Ω, POUT = 1W) ● 22.8μVRMS Output Noise (AV = 15dB) ● Low 0.013% THD+N at 1kHz ● No MCLK Required ● Sample Rates of 8kHz to 96kHz ● Supports Left, Right, or (Left/2 + Right/2) Output ● Sophisticated Edge Rate Control Enables Filterless Class D Outputs ● 77dB PSRR at 1kHz ● Low RF Susceptibility Rejects TDMA Noise from GSM Radios ● Extensive Click-and-Pop Reduction Circuitry ● Robust Short-Circuit and Thermal Protection ● Available in Space-Saving Packages: 1.345mm x 1.435mm WLP (0.4mm Pitch) and 3mm x 3mm TQFN ● Solution Size with Single Bypass Capacitor is 4.32mm2 Applications ● Single Li-ion Cell/5V Devices ● Smart Speakers ● Notebook Computers ● IoT Devices ● Gaming Devices (Audio and Haptics) ● Smartphones ● Tablets ● Cameras #commonpartslibrary #integratedcircuit #linearamplifier #mono

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 2A SOT-23-6 Thin, TSOT-23-6 The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package. • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown • 12V and 24V distributed power bus supplies • Flat screen TV sets and monitors • Power tools and laser printers • White goods and small home appliances • FPGA, DSP, and ASIC supplies • Home audios • Network systems • Set top boxes • Gaming consoles • Consumer electronics #commonpartslibrary #integratedcircuit #AP63203WU7 #BuckConverter #DCDCConverter #PowerManagement #VoltageRegulator #SynchronousBuck #EmbeddedSystems #IndustrialElectronics #PowerSupply #DiodesInc #3V3Power #ElectronicsDesign

!!!Reverse Mount!!! Addressable RGB LEDs 3.2x2.8x1.78 mm 0.2W Intelligent external control surface mount SMD LED #CommonPartsLibrary #LED #Addressable

Buck Switching Regulator IC Positive Fixed 5V 1 Output 1A SOT-23-6 The LMR50410Y5FQDBVRQ1 (part of the LMR50410-Q1 family from Texas Instruments) is a synchronous step-down (buck) DC-DC converter designed for automotive and industrial power applications. It operates over a wide input voltage range of 4 V to 36 V and can deliver up to 1 A output current, making it suitable for converting higher, unregulated voltages into stable lower voltages (e.g., 5 V or 3.3 V rails). The device integrates power switches, control circuitry, and compensation internally, allowing simple design with minimal external components and a compact PCB footprint. Key Features Power & Performance Wide input voltage range: 4 V to 36 V Output current: up to 1 A High switching frequency: 2.1 MHz (enables small inductors) High efficiency with PFM (light load) and FPWM (constant frequency) options Integration & Ease of Use Synchronous rectification (integrated high-side & low-side MOSFETs) Internal compensation (no complex external tuning) Minimal external components required Small SOT-23-6 package for compact designs Protection & Reliability Cycle-by-cycle current limit Short-circuit protection (hiccup mode) Thermal shutdown protection Undervoltage lockout (UVLO) ±1% reference voltage accuracy Automotive & Industrial Capability AEC-Q100 qualified (automotive grade) Operating temperature: Ambient: up to 125°C Junction: up to 150°C Designed for rugged automotive environments Additional Features Soft-start for controlled startup Precision enable pin for system control Monotonic startup with pre-biased output Available in fixed output (e.g., 5 V) variants Typical Applications Automotive electronics (ADAS, infotainment, lighting) Industrial power supplies Distributed power systems General-purpose DC-DC regulation #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

Board Mount Humidity Sensors Intermediate Humidity and Temperature Sensor Humidity, Temperature 0 ~ 100% RH I2C ±1.8% RH 4 s Surface Mount The SHT41-AD1B-R2 is a fully calibrated, low-power environmental sensor that measures relative humidity (RH) and temperature. It integrates sensing elements, signal processing, and a digital interface into a small surface-mount package, making it ideal for space-constrained designs. Key Features Sensor Type: Digital humidity and temperature sensor Interface: I²C (easy MCU integration) Supply Voltage: ~1.08 V to 3.6 V Humidity Accuracy: up to ±1.8% RH (typical) Temperature Accuracy: up to ±0.2 °C (typical) Response Time: Fast measurement and low latency Power Consumption: Ultra-low, suitable for battery devices Package: DFN (compact, ~1.5 × 1.5 mm) Factory Calibration: No external calibration required Functional Overview The sensor uses capacitive humidity sensing combined with a bandgap temperature sensor. Internal electronics convert these measurements into digital data via I²C, eliminating the need for external ADCs or complex signal conditioning. Design Advantages Small footprint for compact PCBs Low power consumption for IoT and portable devices High reliability with long-term stability Fast response time for real-time monitoring Simple integration with microcontrollers Typical Applications IoT and smart home devices HVAC and climate control systems Wearables and portable electronics Industrial monitoring systems Environmental data logging #CommonPartsLibrary #Sensors,-Transducer #Humidity #Moisture-Sensor #SHT4x

Bluetooth, WiFi 802.11b/g/n, Bluetooth v5.0 Transceiver Module 2.4GHz Antenna Not Included, U.FL Surface Mount The ESP32-S3-WROOM-1U-N16R8 is a high-performance embedded module designed for IoT and edge computing applications, featuring integrated wireless connectivity and enhanced processing capabilities. Processor: Dual-core Xtensa LX7, up to 240 MHz Wireless Connectivity: Wi-Fi 2.4 GHz (802.11 b/g/n) Bluetooth LE 5.0 Memory Configuration (N16R8): 16 MB Flash memory 8 MB PSRAM Antenna Type: U.FL connector for external antenna (“1U” variant) Indicates support for an external antenna via U.FL connector Allows improved RF performance and flexible antenna placement #commonpartslibrary #rf #wireless #transceiver #module

NC pin, also called unconnected or no connect pins. It represent pins in IC terminals with no internal connection and no external function.

Seeed Studio XIAO ESP32S3 leverages dual-core ESP32S3 chip, supporting both Wi-Fi and BLE wireless connectivities, which allows battery charge. It integrates built-in camera sensor, digital microphone. It offers 8MB PSRAM, 8MB FLASH, and external SD card slot. All of these make it suitable for embedded ML, like intelligent voice and vision AI. #SeeedStudio #xiao

The TPS6213x series, manufactured by Texas Instruments, includes highly efficient, easy-to-use synchronous step-down DC-DC converters optimized for applications requiring high power density. These converters operate within a wide input voltage range from 3 V to 17 V and are capable of delivering up to 3 A of continuous output current. The series comprises multiple part numbers, namely TPS62130, TPS62130A, TPS62131, TPS62132, and TPS62133, each offering unique output configurations—adjustable outputs for TPS62130 and TPS62130A, and fixed outputs of 1.8 V, 3.3 V, and 5.0 V for TPS62131, TPS62132, and TPS62133 respectively. Key features of the TPS6213x series include the advanced DCS-Control™ topology for improved transient response and high output voltage accuracy, a programmable soft start, seamless transition to power save mode, and selectable operating frequency (either 1.25 MHz or 2.5 MHz). The device also encapsulates robust protection mechanisms such as short circuit and overtemperature protection. Housed in a compact 3-mm x 3-mm QFN-16 package, the IC includes additional functions like a power-good output and 100% duty cycle mode for low dropout conditions. With a highly integrated design that requires minimal external components, the TPS6213x series is ideal for step-down regulation in various applications including standard 12-V rail supplies, POL supplies, embedded systems, and portable devices.

USB Controller USB 2.0 I2C Interface 24-QFN (4x4) The STUSB4500QTR is a standalone USB Type-C Power Delivery (PD) controller from STMicroelectronics designed for power sink applications (devices that receive power, like chargers, IoT devices, or battery-powered systems). It enables automatic negotiation of USB Power Delivery contracts (up to 100 W: 20 V / 5 A) without requiring an external microcontroller, thanks to its built-in auto-run algorithm. Power profiles (PDOs) can be pre-configured and stored in internal non-volatile memory, simplifying system design and reducing component count. The device is optimized for modern USB-C designs, offering robust protection, high-voltage tolerance, and support for operation even from a dead battery state. Key Features Power Delivery & Control Standalone USB Type-C™ and USB PD sink controller Supports up to 100 W (20 V, 5 A) power negotiation Auto-run mode (no MCU required) for PD negotiation Up to 3 configurable sink PDO profiles stored in NVM Power Management Dead battery mode support (can start with no battery power) Dual power supply inputs: V_SYS: 3.0 V – 5.5 V V_DD: 4.1 V – 22 V Integrated VBUS monitoring and control Integrated Functions Built-in VBUS switch gate drivers (PMOS) Internal/external VBUS discharge paths I²C interface for configuration and monitoring Protection & Reliability Short-to-VBUS protection on CC pins (up to 22 V) High-voltage tolerance: Up to 28 V on VBUS pins ESD protection: 3 kV HBM / 1.5 kV CDM Physical & Environmental Package: QFN-24 (4×4 mm) Operating temperature: –40°C to +105°C Industrial-grade reliability Compliance & Compatibility Certified for: USB Type-C Rev 1.2 USB PD Rev 2.0 Interoperable with USB PD 3.0 #commonpartslibrary #integratedcircuit #usbcontroller

Temperature Sensor Digital, Local -55°C ~ 150°C 16 b 6-WSON (2x2) The TMP117AIDRVR is a high-precision digital temperature sensor manufactured by Texas Instruments. The device provides accurate temperature measurements through an I²C-compatible digital interface and is optimized for applications requiring medical-grade accuracy, low power consumption, and compact PCB footprint. The sensor integrates a precision temperature sensing element, analog-to-digital converter, calibration memory, and digital interface into a single compact package. The device supports continuous conversion and shutdown operating modes, enabling efficient thermal monitoring in battery-powered and always-on systems. Internal calibration minimizes external component requirements while providing highly linear and repeatable temperature measurements across an extended operating range. The TMP117AIDRVR is commonly used in industrial controls, wearable electronics, healthcare equipment, environmental monitoring systems, battery management systems, consumer electronics, and precision instrumentation. Electrical Characteristics Supply voltage supports low-voltage digital systems and portable electronics applications. Ultra-low operating current enables long battery life in energy-sensitive designs. Integrated EEPROM allows programmable offset correction and configuration storage. Digital output eliminates the need for external ADC circuitry. High measurement resolution supports precision thermal monitoring applications. Low self-heating characteristics improve measurement stability and accuracy. Functional Features High-accuracy digital temperature sensing. I²C and SMBus compatible communication interface. Programmable alert functionality for thermal threshold monitoring. Continuous conversion and low-power shutdown operating modes. Integrated non-volatile memory for user configuration storage. Wide operating temperature range for industrial and commercial environments. Fast conversion timing suitable for real-time monitoring systems. Factory-calibrated performance requiring minimal external calibration. Package Information Package type is WSON with compact surface-mount footprint suitable for dense PCB layouts. Moisture-sensitive package designed for automated assembly processes. Lead-free and RoHS-compliant construction. Typical Applications Medical thermometers and patient monitoring systems. Industrial temperature monitoring equipment. Battery-powered portable electronics. HVAC and environmental sensing systems. Data acquisition and instrumentation systems. Server and embedded thermal management applications. Consumer electronics requiring precision thermal sensing. #commonpartslibrary #integratedcircuit #temperaturesensor

OR Controller N+1 ORing Controller N-Channel 1:1 TSOT-23-8 The LM74700QDDFRQ1 is an automotive-qualified ideal diode controller designed to provide reverse polarity protection, reverse current blocking, and input power path management in low-voltage DC power systems. The device controls an external N-channel MOSFET to emulate an ideal diode with very low forward voltage drop and reduced power dissipation compared to conventional Schottky diodes. It is optimized for automotive and industrial applications requiring robust protection against negative supply voltages, load dump conditions, and reverse battery events. The controller supports wide input voltage operation and integrates fast response circuitry for fault handling and transient protection. The device is suitable for power OR-ing, hot-swap, redundant power supply systems, and battery-connected applications where efficiency, reliability, and thermal performance are critical. Engineering Specification Device Type Automotive ideal diode controller with reverse battery and reverse current protection Qualification Standard AEC-Q100 qualified for automotive applications Control Topology External N-channel MOSFET controller for ideal diode operation Input Voltage Range Supports wide automotive and industrial supply voltage ranges Reverse Polarity Protection Provides protection against negative input voltage conditions and reverse battery connection Reverse Current Blocking Actively prevents reverse current flow during output-to-input fault conditions Forward Voltage Drop Low conduction losses through external MOSFET control for high-efficiency power delivery Transient Protection Capable of handling automotive transient events including load dump conditions Gate Drive Control Integrated gate driver optimized for fast MOSFET switching and protection response Power Path Management Supports power OR-ing and redundant supply architectures Fault Response Fast turn-off during reverse current and fault events Current Consumption Low operating quiescent current suitable for always-on systems Thermal Performance Designed for efficient thermal operation with external MOSFET-based power dissipation Operating Temperature Range Automotive-grade extended temperature operation Package Type Small-outline automotive package suitable for compact PCB layouts #commonpartsLibrary #integratedcircuit #powermanagement #orcontroller

Buck Switching Regulator IC Positive Adjustable 1.8V 1 Output 750mA 8-VFDFN The TPS62840 is a high-efficiency step-down converter with ultra-low operating quiescent current of typically 60 nA. The device contains special circuitry to achieve just 120 nA IQ in 100% mode to further extend battery life near the end of discharge. The device uses DCS-Control to cleanly power radios and operates with a typical switching frequency of 1.8 MHz. In Power-Save Mode, the device extends the light load efficiency down to a load current range of 1 μA and below. 16 predefined output voltages can be selected by connecting a resistor to pin VSET, making the device flexible for various applications with a minimum amount of external components. The STOP pin of the device immediately eliminates any switching noise in order to take a noise-free measurement in test and measurement systems. The TPS62840 provides an output current of up to 750 mA. With an input voltage of 1.8 V to 6.5 V, the device supports multiple power sources such as 2S to 4S Alkaline, 1S to 2S Li-MnO2 , or 1S Li-Ion/LiSOCl2 Features 1• 60-nA operating quiescent current • 100% duty-cycle mode with 120-nA IQ • Input voltage range VIN from 1.8 V to 6.5 V • Output current up to 750 mA • RF friendly DCS-Control™ • 80% efficiency at 1 µA IOUT (3.6 VIN to 1.8 VOUT) • 16 selectable output voltages via VSET pin • Auto transition PFM/PWM or forced-PWM mode • Selectable forced PWM and STOP modes • Output discharge function • 25-nA shutdown current #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

Temp Monitoring System (Sensor) - External Sensor SPI Output 20-SSOP #commonpartslibrary #sensor #Temperaturesensor #integratedcircuit