Flyback, Forward Converter Regulator Positive, Isolation Capable Output Step-Up/Step-Down - DC-DC Controller IC 16-SOIC

Buck Regulator Positive Output Step-Down - DC-DC Controller IC 32-WQFN (5x5)

LED Driver IC 16 Output Linear PWM Dimming 25mA 5.5V 28-TSSOP PCA9685PW,118 is a 16-channel, 12-bit PWM LED controller with an I²C interface designed for LED dimming, RGB/RGBA lighting, and servo motor control applications. It provides independent PWM control for up to 16 outputs, allowing precise brightness or position control while minimizing MCU GPIO usage. The device supports Fast-mode Plus I²C communication up to 1 MHz and operates from a 2.3 V to 5.5 V supply range. It is commonly used in robotics, LED backlighting, automation systems, and PWM expansion modules for microcontrollers such as Arduino, ESP32, and Raspberry Pi. Key Features 16 independent PWM output channels 12-bit PWM resolution (4096 steps) Programmable PWM frequency from approximately 24 Hz to 1526 Hz I²C Fast-mode Plus compatible interface up to 1 MHz Six hardware address pins allowing up to 62 devices on one I²C bus Programmable open-drain or totem-pole outputs Output capability: 25 mA sink current 10 mA source current Internal 25 MHz oscillator with optional external clock input Individual programmable LED ON/OFF timing for reduced EMI and current surges Supports software reset and group addressing (All Call/Sub Call) 5.5 V tolerant inputs and outputs Operating voltage range: 2.3 V to 5.5 V Package: 28-pin TSSOP (PW suffix) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LEDdriver

OR Controller N+1 ORing Controller N-Channel 1:1 12-WSON (3x3) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #OR-Controller #Ideal-Diode #LM74800

Flyback Regulator Positive, Isolation Capable Output Step-Up/Step-Down - DC-DC Controller IC 10-MSOP-EP

Power Supply Controller Secondary-Side Controller, Synchronous Rectifier 8-SOIC

Buck Regulator Positive Output Step-Down DC-DC Controller IC 20-HTSSOP #commonpartslibrary #integratedcircuit #buckregulator #pmic

Power Supply Controller Power Supply Monitor, Sequencer 28-TQFN (4x4)

133MHz LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHS RP2040 The RP2040 is a high-performance, low-cost 32-bit microcontroller developed by Raspberry Pi Ltd.. It features dual ARM Cortex-M0+ processor cores, flexible digital interfaces, and a unique Programmable I/O (PIO) subsystem that enables custom hardware protocols and timing-critical applications. The device is widely used in embedded systems, IoT devices, robotics, industrial control, consumer electronics, and educational projects. Key Features Dual ARM Cortex-M0+ CPU cores operating up to 133 MHz (up to 200 MHz under specific conditions) 264 KB on-chip SRAM organized in six independent memory banks External QSPI Flash interface with Execute-In-Place (XIP) support and up to 16 MB Flash memory capability 30 multifunction GPIO pins with extensive peripheral multiplexing 2 × UART interfaces 2 × SPI controllers 2 × I²C controllers 16 PWM channels for motor control and signal generation USB 1.1 Host and Device support with integrated PHY 12-bit ADC with four external analog inputs and internal temperature sensor, up to 500 ksps sampling rate 12-channel DMA controller for efficient data transfers Programmable I/O (PIO) subsystem with 8 state machines for implementing custom communication interfaces and precise timing applications Integrated PLLs and programmable LDO regulator for clock and power management Operating voltage range: 1.8 V to 3.3 V Available in a compact 7 mm × 7 mm QFN-56 package Typical Applications IoT and connected devices Industrial automation Robotics and motor control Human-machine interfaces (HMI) Consumer electronics USB peripherals Sensor data acquisition systems Educational and maker projects Custom communication protocol implementations using PIO #CommonPartsLibrary #IntegratedCircuit #Microcontroller

Buck-Boost Regulator Positive Output Step-Up/Step-Down DC-DC Controller IC 24-SSOP #commonpartslibrary #integratedcircuit #powermanagement #buckboostregulator #stepup #stepdown #dcdccontroller

OR Controller N+1 ORing Controller N-Channel N:1 8-VSSOP The LM74610QDGKRQ1 is an automotive-qualified smart bypass ideal diode controller designed to drive an external N-channel MOSFET for reverse polarity protection and input supply OR-ing applications. The device minimizes forward voltage drop and power dissipation compared to traditional Schottky diodes while providing robust protection against reverse battery conditions. It supports operation across a wide automotive input voltage range and is optimized for high-current systems requiring low standby current, fast response, and reliable transient handling. The device is AEC-Q100 qualified for automotive applications and is commonly used in ECU power distribution, battery protection, and redundant supply systems. Engineering Specification Manufacturer: Texas Instruments Manufacturer Part Number: LM74610QDGKRQ1 Device Type: Automotive Smart Diode Controller Qualification Standard: AEC-Q100 Automotive Qualified Functionality: Reverse polarity protection and ideal diode control using external N-channel MOSFET Topology: Charge pump driven ideal diode controller Input Operating Voltage Range: Wide automotive battery operating range with load dump capability support Reverse Input Protection: Supports reverse battery protection without requiring a reverse polarity diode Gate Drive Method: Integrated charge pump for external N-channel MOSFET enhancement Forward Voltage Drop: Determined primarily by external MOSFET RDS(on) Quiescent Current: Ultra-low operating current for always-on automotive systems Transient Immunity: Automotive load dump and ISO transient tolerant design MOSFET Compatibility: External N-channel MOSFET Response Time: Fast reverse current blocking response Operating Temperature Range: Automotive extended temperature range Package Type: VSSOP Package Size: 8-pin small-outline package Mounting Type: Surface mount #Commonpartslibrary #Integratedcircuit #Powermanagement #orcontrollers

ARM® Cortex®-M4 series Microcontroller IC 32-Bit Single-Core 168MHz 1MB (1M x 8) FLASH 64-LQFP (10x10) Arm® Cortex®-M4 32b MCU+FPU, 210DMIPS, up to 1MB flash/192+4KB RAM, USB OTG HS/FS, Ethernet, 17 TIMs, 3 ADCs, 15 comm. interfaces, and camera Includes ST state-of-the-art patented technology • Core: Arm® 32-bit Cortex®-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator) allowing 0-wait state execution from flash memory, frequency up to 168 MHz, memory protection unit, 210 DMIPS/ 1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions • Memories – Up to 1 Mbyte of flash memory – Up to 192+4 Kbytes of SRAM including 64- Kbyte of CCM (core coupled memory) data RAM – 512 bytes of OTP memory – Flexible static memory controller supporting CompactFlash™, SRAM, PSRAM, NOR and NAND memories • LCD parallel interface, 8080/6800 modes • Clock, reset, and supply management – 1.8 V to 3.6 V application supply and I/Os – POR, PDR, PVD and BOR – 4-to-26 MHz crystal oscillator – Internal 16 MHz factory-trimmed RC (1% accuracy) – 32 kHz oscillator for RTC with calibration – Internal 32 kHz RC with calibration • Low-power operation – Sleep, Stop, and Standby modes –VBAT supply for RTC, 20×32-bit backup registers + optional 4 KB backup SRAM • 3×12-bit, 2.4 MSPS A/D converters: up to 24 channels and 7.2 MSPS in triple interleaved mode • 2×12-bit D/A converters • General-purpose DMA: 16-stream DMA controller with FIFOs and burst support • Up to 17 timers: up to twelve 16-bit and two 32- bit timers up to 168 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input • Debug mode – Serial wire debug (SWD) & JTAG interfaces – Cortex-M4 Embedded Trace Macrocell™ • Up to 140 I/O ports with interrupt capability – Up to 136 fast I/Os up to 84 MHz – Up to 138 5 V-tolerant I/Os • Up to 15 communication interfaces – Up to 3 × I2C interfaces (SMBus/PMBus) – Up to 4 USARTs/2 UARTs (10.5 Mbit/s, ISO 7816 interface, LIN, IrDA, modem control) – Up to 3 SPIs (42 Mbits/s), 2 with muxed full-duplex I2S to achieve audio class accuracy via internal audio PLL or external clock – 2 × CAN interfaces (2.0B Active) – SDIO interface • Advanced connectivity – USB 2.0 full-speed device/host/OTG controller with on-chip PHY – USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, on-chip full-speed PHY and ULPI – 10/100 Ethernet MAC with dedicated DMA: supports IEEE 1588v2 hardware, MII/RMII #commonpartslibrary #integratedcircuit #microcontroller

Ethernet Physical Layer Controller 10/100/1000 Base-TX PHY RGMII, SGMII Interface 48-VQFN (7x7) #commonpartslibrary #integratedcircuit

Hot Swap Controller 1 Channel General Purpose 23-LQFN-CLIP (6x5) The TPS16850VMAR is an automotive-grade integrated hot-swap and protection controller designed for robust power-path management in low-voltage DC systems. The device provides comprehensive protection features including overvoltage protection, undervoltage protection, reverse current blocking, inrush current control, overcurrent protection, and short-circuit protection. It is intended for applications requiring controlled power delivery and fault isolation in harsh electrical environments. The device integrates dual back-to-back MOSFET control to support bidirectional current blocking and safe power switching. Adjustable protection thresholds and timing parameters allow flexible system configuration for various power rail requirements. The TPS16850VMAR supports operation across a wide supply voltage range and is optimized for automotive and industrial systems requiring high reliability and transient immunity. The controller includes fault reporting and system status monitoring functions to support intelligent power management architectures. Soft-start capability minimizes inrush current during startup, reducing stress on connectors, power supplies, and downstream circuitry. Integrated thermal protection enhances system safety during abnormal operating conditions. The TPS16850VMAR is qualified for automotive applications and complies with AEC-Q100 requirements. The device is provided in a compact VQFN package suitable for space-constrained designs and high-density PCB layouts. Key Features Automotive-qualified hot-swap and eFuse controller Wide operating input voltage range Adjustable overvoltage and undervoltage protection Reverse current and reverse polarity protection Inrush current control with programmable soft-start Adjustable overcurrent and short-circuit protection Fault monitoring and reporting outputs Integrated thermal shutdown protection Back-to-back MOSFET control architecture Fast fault response and isolation Support for controlled power sequencing Designed for harsh automotive electrical environments AEC-Q100 qualified for automotive applications Compact VQFN surface-mount package Applications Automotive electronic control units Infotainment and telematics systems ADAS and camera modules Industrial power distribution Hot-swappable system power rails Battery-powered embedded systems Power-path management systems Protection for sensitive downstream electronics Electrical Characteristics Operates from low-voltage DC power rails Supports programmable protection thresholds Integrated current sensing and fault detection High transient immunity for automotive environments Low standby current operation Fast response to overload and fault conditions Mechanical Characteristics Surface-mount VQFN package Compact footprint for dense PCB layouts RoHS-compliant package construction Suitable for automated assembly processes Environmental and Reliability Specifications Automotive AEC-Q100 qualified Extended operating temperature range ESD protection on interface pins Designed for high-reliability applications Supports operation in electrically noisy environments #commonpartslibrary #integratedcircuit #powermanagement #hotswapcontrollers

10/100Mb SPI Ethernet controller with TCP/IP stack, LQFP-48 WIZnet Ethernet controller LQFP*7x7mm*P0.5mm*

Buck Regulator Positive Output Step-Down DC-DC Controller IC 20-VQFN (3.5x4.5) #commonpartslibrary #integratedcircuit

Buck-Boost Regulator Positive Output Step-Up/Step-Down DC-DC Controller IC 28-HTSSOP #commonpartslibrary #integratedcircuit #powermanagement #dcdcswitching

JoyWarrior 10bit, 3 axis, joystick controller, SOIC-24 #commonpartslibrary #Interface #HID #integratedcircuit

USB Hub Controller USB 2.0 USB Interface 64-QFN (9x9) #commonpartslibrary #integratedcircuit #usbhubcontroller #interface

JoyWarrior 8bit, 4 axis, joystick controller, DIP-24/SOIC-24 #commonpartslibrary #Interface #HID #integratedcircuit

Microphone Preamplifiers High-Perform Digital Pre-Amp Controller

I2C 1-4 cell NVDC Buck-Boost battery charge controller with USB type C PD support

60V dual 2-phase synchronous step-down DC/DC controller, continuous conduction, QFN-32

Power Over Ethernet Controller 1 Channel 802.3at (PoE+), 802.3af (PoE) 14-TSSOP #CommonPartsLibrary #IntegratedCircuit #PowerManagement #PoE-Controller #TPS23753