Single-subsystem 3.3 V synchronous buck-boost regulator reference built around the TI TPS63802DLAR in a 10-pin VSON package. The design accepts a VBUS input rail into VIN, uses a Bourns SRP4020TA-4R7M 4.7 µH power inductor between L1/L2, and generates PP3V3 from the adjustable TPS63802 output path. The TPS63802 metadata lists a 1.3 V to 5.5 V input range, 2 A output current, selectable switching-frequency modes around 1.4 MHz to 2.1 MHz, and -40 °C to +125 °C junction operation. Support circuitry includes 22 µF and 1 µF ceramic input/output capacitors, a 511 kΩ / 91 kΩ feedback divider for the PP3V3_FB node, a VBUS-derived enable divider using 93.1 kΩ and 100 kΩ resistors, MODE tied to GND, and a 100 kΩ pull-up from PP3V3 to the power-good output. Intended as a reusable compact 3.3 V buck-boost power-supply module for USB, battery, portable, IoT, or embedded sensor designs.

18 V battery-powered BLDC blower control board using an Arduino Nano, LM2596 5 V buck module, P-channel MOSFET power cutoff, battery voltage sensing, potentiometer input, buzzer, and red/green status LEDs. High-current 18 V blower path is sized for up to 5 A.

Carrier PCB schematic for a four-wheel Arduino Nano ESP32 spy car using two TB6612FNG motor-driver modules, removable Nano sockets, servo/sensor/light/buzzer connectors, and protected shared battery power. PCB layout is intentionally deferred pending module dimensions and electrical ratings.

Isolated 220 VAC to 5 V / 2 A power supply using a certified AC-DC module, with potentiometer-controlled PWM output for a 5 V load. Includes mains input protection and safety documentation assumptions.

USB-C powered consumer temperature/humidity sensor node using a low-power Wi‑Fi + BLE 5.x MCU module, digital T/RH sensor, protected 5 V USB-C input, and 3.3 V regulation.

25 mm circular BLE wearable pendant for ambient-light tracking using an ISP1807 module, AS7343 sensor, USB-C LiPo charging, and SWD programming pads.

Production-oriented 2-layer PCB for a desktop mini CRT-style collectible using an ESP32-C3 Mini module, USB-C LiPo charging, ST7789 TFT display, 3 Hall sensors, eject button, piezo buzzer, and battery monitoring.

Production-oriented 2-layer PCB for a desktop mini CRT-style collectible using an ESP32-C3 Mini module, USB-C LiPo charging, ST7789 TFT display, 3 Hall sensors, eject button, piezo buzzer, and battery monitoring.

ESP32-S3 carrier board with USB-C 5V power, BNO085 IMU support, GPS module interface, temperature sensing, and a single brushed DC motor driver carrier interface.

Power-section schematic for a 12V DC input generating +4V for a 4G module, +5V, and +3V3 rails with input TVS protection and regulator thermal notes.

Power-section schematic for a 12V DC input generating +4V for a 4G module, +5V, and +3V3 rails with input TVS protection and regulator thermal notes.

Power-section schematic for a 12V DC input generating +4V for a 4G module, +5V, and +3V3 rails with input TVS protection and regulator thermal notes.

Standalone forensic-device mainboard for portable and desktop enclosures, using Raspberry Pi Compute Module direction, IEEE 802.3at PoE+ module power, USB-C power-only input, and a USB write-blocking architecture under review.

Compact USB-C Rechargeable 9V/1A Guitar Pedal Power Supply Module with 18650 Battery

This project is a WiFi Camera with Motion Detection, utilizing ESP32-CAM module and HC-SR501 PIR sensor. The camera is activated by the sensor's output. The system also includes power regulation and communication headers for setup and control. #WiFi #MCU #PIR #ReferenceDesign #project #ESP32 #camera #referenceDesign #edgeComputing #espressif #template #reference-design

Universal PWM Interface Module: 12 V automotive-input board for configurable ECU PWM input conditioning and open-collector fan-module output, with TVS/reverse-polarity/PTC protection, 5 V buck, 3.3 V LDO, selectable pull-up rails, inversion jumper, status LEDs, test pads, mounting holes, and DT13-08PA connector placeholder.

ATX PSU carrier board for powering a Shugart 800 drive: +24V, +5V, -5V, and a fused 12V feed for an external pure-sine 110VAC inverter module.

Fast USB-C thumb-drive carrier for a managed solder-down USB 3.x flash module, targeting permanently attached 128 GB, 256 GB, or 512 GB storage.

This is a Pet Tracker Reference Design based on STM32L4. Tracker connects with network by SIM800L module connected to the STM. Also MCU connected to the GPS by uart and send data to server #STM32 #GPS #G4 #G3 #LTE #IoT #Tracker #smartHomeDevices #referenceDesign #edge-computing #edgeComputing #stm #template #referenceDesign

Carrier board for the RAK3312 ESP32-S3/SX1262 LoRaWAN module with USB-C 5 V input, 1 A 3.3 V rail, SEN66 sensor connector, RGB status LED, and reset control.

Phone-sized handheld voice assistant built around a Raspberry Pi Compute Module 5 carrier PCB with battery power, USB-C charging, microphones, speaker, small display, wireless connectivity, and user buttons for local voice-assistant and edge-AI workloads.

Four-channel electrochemical gas sensor signal-conditioning module based on the TI LMP91000EVM architecture, with shared I2C, per-channel SPI ADCs, 2.5V reference, sensor headers, and STM32F767ZI interface.

Compact USB dongle PCB for Midea air conditioners based on the mideahvac-dongle architecture, using an ESP32-C6 module, 5V UART level shifting, WS2812B status LED, USB-A appliance connector, and USB-C programming/power.

USB-C powered low-power temperature and humidity sensor node using an ESP32 Wi‑Fi/BLE module, digital T/RH sensor, protected 5V input, and 3.3V system rail for consumer environmental monitoring.

Low-power consumer temperature/humidity sensor node using USB-C 5 V input, protected 3.3 V power, and an ESP32-class Wi-Fi/BLE 5.x module.