Low-power USB-C 5V environmental sensor node with robust input protection, ESP32 Wi-Fi/BLE connectivity, digital temperature/humidity sensing, Bluetooth peripheral syncing, and EEG/PPG sensor interfaces for prototype biosignal acquisition.

Cow health-monitoring wearable PCB for a cow-mounted device. Rear strap electronics target 20-25 g and front sensing assembly target about 15 g. Uses an ESP32-based sensor controller, 200 mAh LiPo battery, battery charging circuitry, and interfaces for ammonia, methane, IR temperature, and saliva sensing. Design must tolerate moisture, mucus, debris, vibration, fur contact, and tongue/lick exposure while remaining compact and lightweight for wearable use.

SCADA Sensor Node v2.1 using a Heltec WiFi LoRa 32 V4 module with separate +5V and board-generated +3V3 rails, ADS131M08 8-channel ADC front end, TCA9548A I2C multiplexer, TMP102-based fan control, ULN2003A relay and fan driver, CT/pressure/analog/One-Wire/vibration/humidity/Qwiic/flow/digital sensor interfaces, relay outputs, fan connector, brownout sensing, and a 200 mm x 140 mm 2-layer layout with Heltec keepout, antenna clearance, mounting holes, and DIN-rail slots.

Wearable health device prototype schematic with ECG sensing via AD8232, motion sensing via BNO085 or BMI270 IMU breakout, on-board processing using TI TM4C123G LaunchPad or MSPM0G3507 LaunchPad, optional ESP8266 Wi-Fi, LiPo battery charging with MCP73831, regulated 3.3 V power from TPS63031 buck-boost or AP2112 LDO prototype option, and user interfaces including electrode connector, JST battery connector, programming header, and optional on/off switch.

CNC hydraulic press brake controller with STM32H743, ADS1256, 5x DAC8501 ±10V outputs, 3x AD598 LVDT interfaces, isolated 24V digital inputs, 100BASE-TX Ethernet, watchdog, E-stop hardware disable, and 4-layer 220mm x 160mm PCB architecture. Domains: field 24V I/O, precision analog, logic/Ethernet. Safety behavior: E-stop and valve-disable force all analog command outputs to 0V-safe state and disable field enables; watchdog and power-good supervisor reset MCU on comms or rail faults. PCB constraints: L1/L4 signal+components, L2 solid GND, L3 power plane, 1.0mm board inset margin, RJ45 at edge, field connectors on opposite edge, isolation corridor between field wiring and logic/Ethernet, 4x M4 plated mounting holes inset 10mm from corners.

This project is designed to measure water level of two tanks using ultrasonic sensors interfaced with the ESP32 microcontroller. The design leverages the processing power and wireless connectivity of the ESP32 to accurately monitor water levels and support automated water management processes. Key components include two ultrasonic sensors for precise distance measurement, robust voltage regulation using an LM2596 buck converter, and reliable power management circuits. Its modular design approach facilitates easy expansion and integration with other systems, making it an ideal solution for both DIY enthusiasts and professionals in automated fluid control and IoT applications. #ESP32 #UltrasonicSensor #WaterLevelSensor #LM2596 #VoltageRegulator #ModularDesign #IoT #DIYProjects #ElectronicsDesign #automation

Two-PCB low-noise EEG system: Digital board (ESP32-S3-MINI-1U + ADS1299 + CP2102N + USB-C + 1S Li-ion charger/power-path + DF40 mezzanine) and Analog board (3x ADS1299 + REF/BIAS/DRL + driven-shield electrode interfaces + local low-noise regulation + test points). DF40 mezzanine carries only power + digital SPI/control with shared SPI, shared START/RESET, and separate CS/DRDY per AFE. 4-layer stacks with strong analog/digital partitioning and interleaved GND pins on DF40.

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #internetOfThings #smartHomeDevices #SeeedStudio #XIAO #LoRa #RP2040 #IoT

This project is designed to measure water level of two tanks using ultrasonic sensors interfaced with the ESP32 microcontroller. The design leverages the processing power and wireless connectivity of the ESP32 to accurately monitor water levels and support automated water management processes. Key components include two ultrasonic sensors for precise distance measurement, robust voltage regulation using an LM2596 buck converter, and reliable power management circuits. Its modular design approach facilitates easy expansion and integration with other systems, making it an ideal solution for both DIY enthusiasts and professionals in automated fluid control and IoT applications. #ESP32 #UltrasonicSensor #WaterLevelSensor #LM2596 #VoltageRegulator #ModularDesign #IoT #DIYProjects #ElectronicsDesign #automation

Sterilizer Control PCB v0 – Enhanced Communication and Peripherals Interfaces

Dual-GPU OAM Accelerator Module with PCIe Gen5, CXL, Advanced Power Sequencing, and Integrated Management Interfaces

ESP32 Motor Driver Board with Sensor, Battery Management, and Peripheral Interfaces

This project is designed to measure water level of two tanks using ultrasonic sensors interfaced with the ESP32 microcontroller. The design leverages the processing power and wireless connectivity of the ESP32 to accurately monitor water levels and support automated water management processes. Key components include two ultrasonic sensors for precise distance measurement, robust voltage regulation using an LM2596 buck converter, and reliable power management circuits. Its modular design approach facilitates easy expansion and integration with other systems, making it an ideal solution for both DIY enthusiasts and professionals in automated fluid control and IoT applications. #ESP32 #UltrasonicSensor #WaterLevelSensor #LM2596 #VoltageRegulator #ModularDesign #IoT #DIYProjects #ElectronicsDesign #automation

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #Seeed #XIOA #LoRa #RP2040 #IoT

This project involves designing a complete schematic for a robotic arm controller based on the ESP32-C3 microcontroller, specifically using the ESP32-C3-MINI-1-N4 module. The design features a dual power input system and comprehensive power management, motor control, I/O interfaces, and status indicators—all implemented on a 2-layer PCB. Key Specifications: Microcontroller: • ESP32-C3-MINI-1-N4 module operating at 3.3V. • Integrated USB programming connections with reset and boot mode buttons. Power System: • Dual power inputs with automatic source selection: USB-C port (5V input) and barrel jack (6-12V input). • Power management using LM74610 smart diode controllers for power source OR-ing. • AMS1117-3.3 voltage regulator to deliver a stable 3.3V supply to the microcontroller. • Filter capacitors (10μF electrolytic and 100nF ceramic) at the input and output of the regulators. • Protection features including USBLC6-2SC6 for USB ESD protection and TVS diodes for barrel jack overvoltage protection. Motor Control: • Incorporates an Omron G5LE relay with a PC817 optocoupler and BC547 transistor driver. • Provides dedicated header pins for servo motors with PWM outputs. • Flyback diode protection implemented for relay safety. I/O Connections: • Header pins exposing ESP32-C3 GPIOs: Digital I/O (IO0-IO10, IO18, IO19) and serial communication lines (TXD0, RXD0), plus an enable pin. • Each I/O pin includes appropriate 10kΩ pull-up/pull-down resistors to ensure reliable performance. Status Indicators: • A power status LED with a current-limiting resistor. • A user-controllable LED connected to one of the GPIO pins. PCB Layout Requirements: • 2-layer PCB design with separate ground planes for digital and power sections. • Placement of decoupling capacitors close to power pins to reduce noise. • Adequate trace width for power lines to ensure efficient current flow. • Inclusion of mounting holes at the board corners for secure installation. • All components are properly labeled with correct values for resistors, capacitors, and other passive elements, following standard design practices for noise reduction, stability, and reliability. #RoboticArmController #ESP32C3 #SchematicDesign #PCBDesign #ElectronicsDesign #PowerManagement #MotorControl #EmbeddedSystems #IoT

A general infrared proximity sensor circuit that can be interfaced with any microcontroller (e.g., Arduino, ESP, etc.). It uses a transmitter (IR LED) and a receiver (photodiode) along with a comparator circuit (LM393N/NOPB) to sense objects. The circuit outputs a digital signal (high/low) based on the sensor's response.

Introducing an innovative IoT board designed around the ESP32-WROOM-32 chipset, perfect for projects that require both performance and portability. The system is engineered to operate on a stable external 5V power source while also offering the flexibility of a 12V LiPo battery for on-the-go applications. With seamless integration of both analog and digital sensors and comprehensive support for all standard communication interfaces, this board is your gateway to creating sophisticated and reliable IoT solutions. #IoT #ESP32 #Sensors #5V #LiPoBattery #PortableTech #EmbeddedSystems #Innovation

3.7V Lipo Charger. Interfaces with MT3608 Boost Converter to convert 3.7V to 5V. Slot on top of your Arduino and charge your battery while the Arduino is plugged in. Or run your Arduino portably using the battery.

This project designs a Linux Single Board Computer using STM32MP157FAC1, featuring DDR memory, a power management IC, USB and SD card interfaces, and essential user controls, aimed at versatile embedded applications.

Design for hat board that interfaces with RPi CM4 IO board

This project is a communication device designed with Adafruit's 3857 Microcontroller (U1) and Hoperf's RFM95W-915S2 RF module (U2). The microcontroller interfaces with the RF module via SPI protocol for wireless data transmission. The project also includes a capacitor (C1) and an SMA connector (J1). #LoRa #IoT #project #M4 #Adafruit

A circuit for a gps tracker using stm32f103c8t6 and sim 808, that acquires and sends gps coordinates to a separate interfaced application. The circuit will be powered by a 12v dc battery so there a need for power regulation. there is a USB type micro B for code uploading.

3.7V Lipo Charger. Interfaces with MT3608 Boost Converter to convert 3.7V to 5V. Slot on top of your Arduino and charge your battery while the Arduino is plugged in. Or run your Arduino portably using the battery.

A PCB that interfaces with a smart shoe insole

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #Seeed #XIOA #LoRa #RP2040 #IoT