That file contains the official Würth datasheet and exact MPN, so it was not overwritten because the requested update was conditional on the property being absent. The manufacturer-hosted canonical URL is listed above.
Metadata cross-check
Table
Field
Part data
Datasheet
Result
MPN
2513130810102
2513130810102
Match
Manufacturer
Würth
Würth Elektronik eiSos GmbH & Co. KG
Minor: abbreviated
Pin/pad count
8
8
Match
Description
±1.0 kPa, I²C + analog, horizontal barbed ports
Same exact variant
Match
Package/case
Not set
Custom WSEN-PDUS horizontal-port package
Missing metadata
Datasheet URL
Uploaded official PDF
Official manufacturer PDF available
Valid, noncanonical host
Key specifications
Differential pressure range: −1 to +1 kPa (±10 mbar)
Supply voltage: 3.0–3.6 V; 3.3 V typical
Current consumption: 4 mA typical; 6.5 mA maximum
Interfaces: I²C and analog voltage output
Pressure conversion: 15-bit ADC
Analog output: 11-bit DAC
Typical total accuracy over 0–70 °C: ±0.75% FSS
Typical absolute accuracy at 25 °C: ±0.5% FSS
Response time: 2.2 ms
Analog sensitivity: 0.757 kPa/V
Digital sensitivity: 7.63 × 10⁻⁵ kPa/digit
Operating temperature: −25 to +85 °C
Compensated temperature range: 0 to 70 °C
Maximum common-mode pressure: 2.5 MPa
Differential overpressure / burst rating: 10 kPa
ESD rating: 2 kV HBM
Moisture sensitivity level: MSL 1
Body drawing includes 13.31 ±0.2 mm principal length and 8.0 mm body width; port features extend beyond the body. Use the full dimensioned drawing rather than the simplified 13.3 × 11.6 mm catalog description for enclosure design.
Pin-by-pin cross-check
Table
Pin
Current label
Datasheet function
Expected electrical type
Result
1
SCL
I²C serial clock
Input
Function/number match; type and description missing
2
SDA
I²C serial data
Bidirectional
Function/number match; type and description missing
3
GND
Negative supply
Ground / power
Function/number match; type and description missing
4
VOUT
Analog output
Output
Function/number match; type and description missing
5
VDD
Positive supply
Power input
Function/number match; type and description missing
6
NC
No connection
No-connect
Match; type and description missing
7
RSVD_1
Reserved
Reserved/passive
Number/function match; noncanonical label and metadata missing
8
RSVD_2
Reserved
Reserved/passive
Number/function match; noncanonical label and metadata missing
Pins 6–8 are not functional I/O: pin 6 is NC, while pins 7 and 8 are reserved.
Schematic symbol findings
All eight pin numbers and functional labels are present and map to the correct footprint pads.
Pin arrangement is logical and readable.
Every terminal currently has Pin Type: Unspecified.
Pin Description, Pin Group, Section, Pin Orientation, and Terminal Order metadata are absent.
Pins 7 and 8 are labeled RSVD_1 and RSVD_2; the datasheet calls both RSVD.
The visible MAIN annotation is generic and not a datasheet-defined device label.
Footprint cross-check
The eight copper lands match the recommended pattern:
SMD rectangular lands, top copper/paste/mask
Nominal land size: 1.0 × 2.1 mm
Vertical pitch: approximately 1.52 mm
Pad-row center X positions: ±5.63 mm
Pad Y positions: ±2.285 mm and ±0.760 mm
No drilled pad holes
Pin-1 marker present
STEP model and KiCad footprint asset present
Footprint mismatches / risks
High — Required central routing keepout is missing. The datasheet land pattern marks a central zone where metal, open traces, and vias are prohibited. No enforceable keepout rule/node was found.
High — Courtyard imported into active silkscreen geometry. The KiCad source has a ±7.68 mm by −5.0/+8.6 mm F.CrtYd rectangle, but the Flux Silk Shapes asset includes that rectangle and no separate courtyard node was found. This risks printing an unintended large box and leaves no functional courtyard.
Medium — Pin electrical types and descriptions are absent. This weakens ERC behavior and library usability.
Medium — Package/case metadata is absent. The custom horizontal-port package is not documented in properties.
Medium — Reserved-pin labels are noncanonical.RSVD_1/RSVD_2 are understandable but differ from the datasheet’s RSVD naming.
Medium — Footprint text import is questionable. Reference/value text share source coordinates, and text rules show a 1.27 mm stroke width as well as 1.27 mm font size, suggesting an import mapping issue.
Low — Manufacturer name is abbreviated. Use the full canonical manufacturer name for clean BOM metadata.
Overall assessment
The MPN, variant description, eight-pin mapping, pad numbers, land dimensions, and pad positions match the official datasheet. The most important corrections are adding the datasheet-required center keepout and separating the courtyard from silkscreen. Symbol terminal metadata should also be completed before publishing the part for broad reuse.