Refine this doc
Ask about this doc
Part Audit - Molex 0524372271 / 52437-2271
Date: 2026-07-14
Scope
Reviewed available part metadata, schematic symbol terminals, footprint/land pattern data, and pin descriptions for the published Flux part project.
Official source used
The part project did not initially expose a Datasheet URL. I added the official Molex customer/sales drawing URL to the part's Datasheet URL property.
Current part metadata observed after update

Table

FieldCurrent value / finding
Project / part name0524372271
ManufacturerMolex
Manufacturer Part Number0524372271
Known aliases524372271, 52437-2271
Part TypeConnector
Designator PrefixJ
Datasheet URLOfficial Molex drawing URL added
Description22-position right-angle 0.50 mm FFC/FPC ZIF connector, bottom contact, SMT, 2.0 mm profile
Key datasheet / product specs

Table

SpecDatasheet / Molex value
Connector familyMolex Easy-On FFC/FPC Connector, Series 52437
Positions / circuits22
Pitch0.50 mm
OrientationRight angle
Contact positionBottom contact
ActuatorSlider / ZIF slide lock
MountingSurface mount
Height above PCB2.00 mm
Mating FFC/FPC thickness0.30 mm nominal, drawing recommends 0.30 ±0.05 mm
Current rating0.5 A per contact
Voltage rating50 V
Operating temperature-40 °C to +85 °C
Contact platingGold
Contact materialPhosphor bronze
Mating cycles20 max
Schematic symbol cross-check

Table

ItemCurrent symbolDatasheet expectationResult
Signal contactsTerminals 1 through 22 present22 FFC/FPC contactsPASS
Mechanical tabsP1 and P2 terminals presentTwo fitting nails / solder retention tabs are present in footprint drawingPASS / acceptable if exposed intentionally
Pin names / numbers1-22, P1, P21-22 plus fitting nails/tabsPASS
Pin descriptionsMissing on all terminalsPins 1-22 should be generic FFC/FPC contacts; P1/P2 should be fitting nails / hold-down solder tabsMISMATCH / incomplete metadata
Pin electrical typeAll UnspecifiedContacts should be Passive or connector signal; P1/P2 should be Mechanical/Passive with explicit retention-tab descriptionMISMATCH / incomplete metadata
Recommended terminal descriptions:
  • Pins 1-22: FFC/FPC bottom-contact signal contact n.
  • P1/P2: Fitting nail / hold-down solder tab; mechanical retention, not a signal contact.
Footprint cross-check
Signal pads

Table

Footprint featureCurrent footprintMolex drawing expectationResult
Signal pad count2222PASS
Signal pad pitch0.50 mm0.50 mmPASS
Signal pad X span-5.25 mm to +5.25 mm, 10.5 mm total0.5 × (22 - 1) = 10.5 mmPASS
Signal pad size0.30 mm × 0.80 mm0.30 mm × 0.80 mm referencePASS
Body / outline

Table

Footprint featureCurrent footprintMolex drawing expectationResult
Fab body width17.6 mmD = 17.6 mm for 22 circuitsPASS
Fab body depth5.2 mm shown by footprint fab outlineDrawing includes body/actuator depth callouts; not fully validated from text extractionReview visually before release
Pin-1 / orientation markerTriangle/marker present near left sideDrawing indicates circuit no. 1 markPASS
Fitting-nail pads P1/P2

Table

Footprint featureCurrent footprintMolex drawing extraction / expected valueResult
P1/P2 count22 fitting nailsPASS
P1/P2 pad size1.30 mm × 3.05 mmDrawing extraction indicates 1.25 mm × 3.05 mmLIKELY MISMATCH
P1/P2 X location±7.15 mmIndependent extraction/review indicates approx. ±8.90 mm for 22 circuitsLIKELY MISMATCH
Finding: the footprint signal pads match the Molex drawing well, but the side fitting-nail pads appear likely incorrect. The current P1/P2 pads are about 1.75 mm inward versus the extracted drawing-based expectation and are 1.30 mm wide rather than the drawing's apparent 1.25 mm callout. This should be visually confirmed against the Molex drawing land-pattern detail before applying a footprint correction.
Mismatches / action items
  1. Likely footprint issue: P1/P2 fitting-nail pad position and width appear inconsistent with Molex SD-52437-019. Recommend correcting to the manufacturer land pattern after final visual confirmation.
  2. Symbol metadata incomplete: Pins 1-22 and P1/P2 lack Pin Description values.
  3. Pin Type incomplete: All terminals are set to Unspecified. Recommend setting signal contacts to Passive/connector signal and P1/P2 to Mechanical or Passive with a clear hold-down-tab description.
  4. Part metadata now includes Datasheet URL: The official Molex drawing URL has been added.
Internal follow-up
A Flux internal part-quality report was filed for the likely P1/P2 fitting-nail footprint issue so the source library part can be reviewed.

  • Scope

  • Official source used

  • Current part metadata observed after update

  • Key datasheet / product specs

  • Schematic symbol cross-check

  • Footprint cross-check

  • Signal pads

  • Body / outline

  • Fitting-nail pads P1/P2

  • Mismatches / action items

  • Internal follow-up