Chat

Welcome to Flux

Treat Flux like your intern. Tell it what you'd like to build and it'll get to work. You can also ask it questions, brainstorm ideas, and teach it your preferences. Learn More

Explain project
Write a project description
Find schematic issues
Create a test plan
Simulate a circuit
Prepare for Manufacturing
Component Selection Workflow
New Subsystem Wizard
Write I2C initialization code
Generate firmware skeleton
Sign up to send
what to do in this circuit to trip the relay?
shivam2002

shivam2002

@copilot what to do in this circuit to trip the relay?
2y

copilot

To trip the relay $K1$ in your circuit, we need to create a situation where the relay coil is energized. This can be achieved by sending a signal through the relay control circuit, which typically involves switching a transistor that controls the current through the relay coil. Since the relay in question is SRD-12VDC-SL-C, it requires a 12V supply across its coil to operate.
Based on the project components and connections provided, here's a step-by-step guide to trip the relay $K1$:
  1. Ensure Power Supply: Verify that $V1$ (12V supply) is properly connected and powered, as this voltage is needed to energize the relay's coil.
  2. Transistor Switching Mechanism: To control the relay, we can use $Q1$ or $Q2$ as a switch. For simplicity, let's use $Q2$ (PC817, an optocoupler) in this example. When the LED inside $Q2$ is forward-biased (current flows from ANODE to CATHODE), it will turn on the phototransistor segment, thus allowing current to flow from COLLECTOR to EMITTER, making it possible to control the relay.
    To energize the relay:
    • Activate $Q2$: Apply a signal to the ANODE of $Q2$ through $R2$. This can be done via a GPIO pin from $U1$ (for example, $U1:D8$) set to a high state. Ensure this pin is configured as an output in your Arduino sketch.
    • Connecting $U1:D8$ to $R2:P1$ and ensuring $R2$ is connected to $Q2:ANODE$ (which is already done in your circuit) is the key step here.
Here are the detailed steps summarized:
  • Ensure $V1$ is connected and supplying 12V.
  • Connect $U1:D8$ to $R2:P1$ (already done).
  • Issue a command from the Arduino Nano ($U1$) script to set $D8$ HIGH, which will forward bias the LED in $Q2$, activate the phototransistor, and allow current to flow from $V1$ through $Q2:COLLECTOR$, $Q2:EMITTER$, to energize $K1$'s coil and trip the relay.
This arrangement provides a way to digitally control high-power devices connected to the relay, isolating the microcontroller from the higher voltage circuit controlled by the relay.
2y
shivam2002

shivam2002

is there any issue in this circuit? ensure all the voltage and current requirements are properly satisfied with the use of resistors in this circuit.
2y

copilot

To evaluate the voltage and current requirements and examine potential issues with the use of resistors in the circuit, let's analyze the key components and their connections considering their specifications and typical operating conditions.
1. Relay $K1$ (SRD-12VDC-SL-C)
  • Voltage and Current: The relay requires a 12V supply to operate, which is provided by $V1$. The typical coil current is around 37.5mA at 12V. The existing arrangement through $Q2$ should adequately control the relay coil without an additional resistor directly on the relay coil circuit.
2. Optocoupler $Q2$ (PC817X1CSP9F)
The optocoupler plays a crucial role in isolating the low voltage control signal from the high voltage relay coil circuit.
  • LED Forward Voltage and Current: Typically, the forward voltage of an optocoupler LED is about 1.2 to 1.4V, and the forward current recommendation is around 10 to 20mA for proper operation. However, there's no detailed specification provided for this exact part, so typical values are assumed.
3. Resistor $R2$ for $Q2$ LED
Given that $U1$ (Arduino Nano) operates at 5V on its digital pins:
  • Using the calculations with an assumed forward voltage of $V_F = 1.2V$ and a target forward current of $I_F = 10mA$ for the optocoupler's LED: R=Vsource−VFIF=5V−1.2V10mA=380ΩR = \frac{V_{source} - V_F}{I_F} = \frac{5V - 1.2V}{10mA} = 380\Omega
However, a 330$\Omega$ resistor is used in the project ($R2$), which will slightly increase the current, but this is still within safe limits for typical LEDs.
4. LED1 ($WP7113SYD$)
This LED has a forward voltage of about 2V (as specified in the project) and can handle a forward current up to 30mA. It is critical to ensure this LED is not overdriven.
  • Current Limiting for LED1: Assuming the LED is powered directly from a 12V source ($V1$) with no current-limiting resistor detailed in the path, which is a significant oversight since it can lead to exceeding the maximum forward current and potentially damage the LED.
To properly size a resistor for LED1: R=Vsource−VLEDILED=12V−2V20mA=500ΩR = \frac{V_{source} - V_{LED}}{I_{LED}} = \frac{12V - 2V}{20mA} = 500\Omega A current value of 20mA is chosen to ensure bright illumination without approaching the absolute maximum rating.
Potential Issue Identified
  • Missing Resistor for LED1: There is a critical need for a current-limiting resistor in series with $LED1$ to prevent it from being overdriven by the 12V source. An approximate value of 500$\Omega$ would be appropriate.
Summary
  • The circuit's control path for the relay, via the optocoupler, appears correctly designed.
  • There is a potential oversight with $LED1$, where a current-limiting resistor needs to be added to prevent damage to the LED.
  • All other components and nets should function correctly based on the available information and typical values assumed for calculation purposes.
Before implementing any changes, always verify the exact specifications of your components, as the calculations here are based on typical values and assumptions.
2y
4
Q1
V2
K1
R2
Resistance
330 Ω
D1
V1
R1
Resistance
1kΩ
LED1
Q2
U1
U2
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • Power Net Portal
    Power Net Portal
    Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
    jharwinbarrozo
    11.4M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
    jharwinbarrozo
    15.8k
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • RMCF0805JT47K0
    RMCF0805JT47K0
    47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
    jharwinbarrozo
    1.1M

Strong Olive Interocitor

Strong Olive Interocitor thumbnail
Welcome to your new project. Imagine what you can build here.

Properties

Properties describe core aspects of the project.

Pricing & Availability

Distributor

Qty 1

Digi-Key

$1.35–$1.92

LCSC

$2.32–$2.46

Mouser

$1.02

Controls