The ATtiny45/85 USB Phone Charge Guard regulates charging by monitoring voltage, current, power, and energy, protecting Li-ion batteries.

ATTINY85 to toggle the LEDs of this cute board.

AquaTimer is a programmable timer for 12V devices such as lighting, solenoid valves or pumps not only for aquariums. It has three switchable channels for currents up to 2A each and up to 5A in total. Connected lighting can be dimmed if desired and slowly faded in and out to simulate sunrises and sunsets. The internal RTC of the ATtiny is used as a clockwork in conjunction with a 32.768kHz crystal. A backup battery keeps the clock running even if the external power supply is interrupted. Settings are made using three buttons and the OLED display.

An ATtiny13 is more than sufficient to control almost any number of NeoPixels via an IR remote. The NeoController was originally developed as a tester for 800kHz NeoPixel strips. Since there was still so much flash left in the ATtiny13, an IR receiver was integrated so that some parameters can be controlled with an IR remote control. In this way, it is also suitable as a simple and cheap remote-controlled control unit for NeoPixels. Due to its small size (21.6mm x 11.4mm), it can be soldered directly to the LED strip without any problems. The power supply via a USB-C connection enables currents of up to 3A. There is still more than a third of the flash memory left for additional ideas.

The Qwiic PC Fan Controller allows you easily control almost any PC fan over the Qwiic bus using the on board ATtiny microcontroller and control firmware. The control firmware monitors the tachometer output of the fan in order to implement PI Control over the fan speed, allowing you to set your desired speed in real units.

The ATtiny85 Thermo Buzzer Board is a small but powerful tool that can help you prevent dangerous situations caused by high temperatures, making it an essential device for safety-conscious individuals. #safetyfirst #hightemperaturewarning #electronicsafety #attiny85project #makerscommunity

TinyCandle is a simple tealight candle simulation based on the ATtiny13A.

TinyCharger is an ATtiny25/45/85-based, single-cell Li-ion battery charger with selectable charging current limit (100mA - 1000mA) and an OLED display for monitoring.

A tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lot of power. We wanted to design a microcontroller board that was small enough to fit into any project, and low cost enough to use without hesitation. Perfect for when you don't want to give up your expensive dev-board and you aren't willing to take apart the project you worked so hard to design. It's our lowest-cost arduino-IDE programmable board!

The Arduino WS2812b Controller Shield is a shield designed to offload the implementation of the WS2812b protocol to the shield. It is implemented on an ATtiny85, and the Arduino communicates with the shield over standard SPI. The code for the ATtiny85 can be found at https://github.com/k3jph/ws2812b-spi-controller

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Flashlight controlled by attiny85. Still needs power switch/brightness control

Etapa 1: Recolección y Almacenamiento de Energía Entrada: tus cactus en serie (ej. 15 cactus × 0.5 V = 7.5 V). Componente clave: Supercapacitor o batería recargable de baja capacidad (Li-ion o LiFePO4, 3.7V-7.4V). Diodo Schottky entre los cactus y el capacitor para evitar descarga inversa. 🛠 Ejemplo de componentes: Supercapacitor de 5–10 F, 5.5 V o batería de 3.7 V (tipo 18650). Diodo Schottky 1N5819. Módulo cargador TP4056 (si usas batería). Etapa 2: Aumento de Voltaje (Boost Converter) Conversión de 3.7 V / 7.5 V DC a 110 V AC. Necesitas: Boost Converter (DC-DC Step-up) de hasta 300 V DC. Inversor DC-AC (pequeño, tipo mini inverter para LEDs) que convierta ese voltaje a 110 V AC. NOTA: Algunos focos LED pueden funcionar con 110 V DC directamente, si quieres evitar el inversor. Etapa 3: Detección de Noche Sensor LDR (resistor dependiente de luz) conectado a un comparador (ej. LM393) o a un microcontrolador (como un ATtiny o ESP8266 si quieres funciones extra). Al bajar la luz solar: El comparador activa un MOSFET o un relé que conecta la energía almacenada al foco.

This is a Digispark sub-layout to quickly design your ATtiny85 based projects #ATtiny #sub-layout #pcb

This is a Digispark sub-layout to quickly design your ATtiny85 based projects #ATtiny #sub-layout #pcb

This is a Digispark sub-layout to quickly design your ATtiny85 based projects #ATtiny #sub-layout #pcb

Attiny 84

The ATtiny85 Thermo Buzzer Board is a small but powerful tool that can help you prevent dangerous situations caused by high temperatures, making it an essential device for safety-conscious individuals. #safetyfirst #hightemperaturewarning #electronicsafety #attiny85project #makerscommunity

Sub layout for ATTINY84 in DIP package. Minimal components with ISP programming connector(excluded from BOM)

Sub layout for ATTINY84 in DIP package. Minimal components with ISP programming connector(excluded from BOM)

The ATtiny85 LED controlled board is a compact microcontroller board that can control multiple LEDs. Perfect for DIY electronics projects. #ATtiny85 #LEDcontroller #microcontroller #DIYelectronics #maker

Welcome to your new project. Imagine what you can build here.

Sub layout for ATTINY84 in DIP package. Minimal components with ISP programming connector(excluded from BOM)

Sub layout for ATTINY84 in DIP package. Minimal components with ISP programming connector(excluded from BOM)