BLE remote control board. Based on SoC ESP32-C3-MINI-1 that allows you to program it as HID volume multichannel control, you can switch channels with the user button, or use it as arrow keys. #internetOfThings

BLE remote control board. Based on SoC ESP32-C3-MINI-1 that allows you to program it as HID volume multichannel control, you can switch channels with the user button, or use it as arrow keys.

(AL8805W5) The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8805 part.

Low-power USB-C powered environmental sensor node with a protected 5 V USB-C sink input, TPS26630 front-end protection for reverse/OVP/UVLO/OCP, efficient 3.3 V buck regulation, ESP32-C3 Wi-Fi plus BLE connectivity, and an I2C SHT41 temperature/relative-humidity sensor. The design targets robust operation from USB-C sources advertising 0.5 A to 3 A and is being completed as a schematic ready for PCB layout.

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

Seeed Studio XIAO ESP32S3 leverages dual-core ESP32S3 chip, supporting both Wi-Fi and BLE wireless connectivities, which allows battery charge. It integrates built-in camera sensor, digital microphone. It offers 8MB PSRAM, 8MB FLASH, and external SD card slot. All of these make it suitable for embedded ML, like intelligent voice and vision AI. #SeeedStudio #xiao

Seeed Studio XIAO ESP32C3 adopts new RISC-V architecture, supporting both Wi-Fi and BLE wireless connectivity. For Internet of Things applications, you will find it is flexible and suitable for all kinds of IoT scenarios. #SeeedStudio #xiao

This is a ESP32-C3-WROOM-02U reference design based on the manufacturer's recommendations. On board we have an ESP module, USB C for firmware, 2 connectors with IOs and RGB LED #ESP32 #WiFi #LED #IoT #BLE #ARM #referenceDesign #simple-embedded #espressif #template

- ESP32, WT32-ETH01 Transceiver; 802.11 b/g/n/e/i (Wi-Fi, WiFi, WLAN), Bluetooth® Smart 4.x Low Energy (BLE) 2.4GHz ~ 2.5GHz Evaluation Board #CommonPartsLibrary #DevelopmentBoard #RF #EvaluationBoard #Wifi #Bluetooth #Module

This is a BLE remote control Reference Design. It features a Microchip RN4871U BLE module for communication, various push buttons (Up, Down, Left, Right, OK) for control input, and a piezoelectric buzzer for audio feedback. Power is supplied by a battery and it is regulated to 3.3V for the BLE module. #BLE #IoT #referenceDesign #simple-embedded #microchip #template #reference-design

This is a BLE remote control Reference Design. It features a Microchip RN4871U BLE module for communication, various push buttons (Up, Down, Left, Right, OK) for control input, and a piezoelectric buzzer for audio feedback. Power is supplied by a battery and it is regulated to 3.3V for the BLE module. #BLE #IoT #referenceDesign #simple-embedded #microchip #template #reference-design

This is a BLE Controller project based on E73-2G4M04S1A module with SoC nRF52810 on board. Can be used to control RC cars, robots, planes, drones, etc #robotics #nRF52810 #E73 #Ebyte #BLE #referenceDesign

BLE remote control board. Based on SoC ESP32-C3-MINI-1 that allows you to program it as HID volume multichannel control, you can switch channels with the user button, or use it as arrow keys.

BLE remote control board. Based on SoC ESP32-C3-MINI-1 that allows you to program it as HID volume multichannel control, you can switch channels with the user button, or use it as arrow keys.

Gyroscopio BLE 1

This is a smart watch project based on E73-2G4M04S1A module with SoC nRF52810 on board. OLED display and coin battery #wearable #nRF52810 #E73 #Ebyte #BLE #referenceDesign

Urban Moccasin Replicator – RF Energy-Harvesting BLE Node

Waterproof ESP32-C6 BLE MTB GPS Computer with NEO-M9N, LiPo Power Management, USB-C, and External SMA Antenna

This is a climate control system reference design with a STM32WB5 microcontroller, power manager IC, USB Type-C, JST connectors, and an LCD driver. #referenceDesign #edge-computing #edgeComputing #stm #template #iot #control #BLE #reference-design

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

Dual core, Wi-Fi: 2.4 GHz up to 150 Mbits/s,BLE (Bluetooth Low Energy) and legacy Bluetooth, 32 bits, Up to 240 MHz #esp32 #ble #wifi #arm

Dual core, Wi-Fi: 2.4 GHz up to 150 Mbits/s,BLE (Bluetooth Low Energy) and legacy Bluetooth, 32 bits, Up to 240 MHz #esp32 #ble #wifi #arm