This is a IR2110 high side mosfet driver circuit with mosfet included. This is a circuit I use often and I believe it is time to give it its own board and project.

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

Determine el circuito equivalente de Thévenin entre A y B del circuito mostrado, deberás dibujar el circuito equivalente de Thévenin. Determine VTH y RTH si se conecta un resistor variable de 850 Ω en paralelo entre los extremos de R2 y R3

Learn how to use AI Auto Layout on this ESP32 Espresso Smart Scale! In one click you’ll see AI Auto Layout perform magic. Pay close attention to how we recommend creating rulesets, zones, and fanouts. By copying the setup in this example on your own project, you’ll have a fully routed board in no time!

Learn how to use AI Auto Layout on this ESP32 Espresso Smart Scale! In one click you’ll see AI Auto Layout perform magic. Pay close attention to how we recommend creating rulesets, zones, and fanouts. By copying the setup in this example on your own project, you’ll have a fully routed board in no time!

This is a reference design of TPS56339 DC-DC Converter IC with input voltage 4.5-24V and output 5V and 3A #dcdc #ti #power #3A #5V #referenceDesign #powermanagement #texas-instruments #template #reference-design

Energy Harvesting sub-layout based on a BQ2550 for low powered projects #energy #power #ti #solar

Esquemático para lectura de resistencias flexibles con un ESP32 WROOM 3D

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

AquaTimer is a programmable timer for 12V devices such as lighting, solenoid valves or pumps not only for aquariums. It has three switchable channels for currents up to 2A each and up to 5A in total. Connected lighting can be dimmed if desired and slowly faded in and out to simulate sunrises and sunsets. The internal RTC of the ATtiny is used as a clockwork in conjunction with a 32.768kHz crystal. A backup battery keeps the clock running even if the external power supply is interrupted. Settings are made using three buttons and the OLED display.

A discrete 555 timer plug-in replacement composed of 26 transistors and 16 resistors. #N555 #transistor #resistor

This is the multipurpose PCB that works with Arduino Nano, a way that you can run 2 Stepper motors, 2 DC motors, 2 Servo motors at the same time and this is not it you can even connect BT module, rotary encoder, I2C device, potentiometer at same time. This PCB is very much helpful in building any project and no need to worry about messy wire connections.

The SparkFun ZOE-M8Q GPS Breakout is a high accuracy, miniaturized, GPS board that is perfect for applications that don't possess a lot of space. The on-board ZOE-M8Q is a 72-channel GNSS receiver, meaning it can receive signals from the GPS, GLONASS, BeiDou, and Galileo constellations. This increases precision and decreases lock time and thanks to the onboard rechargable battery you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.

TI BQ25570 step-up DC-DC energy harvester and battery charger

This is a very simple timer circuit. When you push down to turn on the S1, this will turn on the LED and it also will charge the C1 Capacitor. Then upon releasing the push button switch, the LED will stay lit for couple of seconds until C1 is completely discharged.

This is a great battery-backed real time clock (RTC) that allows your microcontroller project to keep track of time even if it is reprogrammed, or if the power is lost. Perfect for datalogging, clock-building, time stamping, timers and alarms, etc. Equipped with PCF8523 RTC - it can run from 3.3V or 5V power & logic!

LCD timer with Arduino that uses an encoder to set the time. The code works but it's limited, feel free to upgrade Feel free to review the board.

Demo its features next meeting by presenting how to create a 555 timer circuit schematic diagram and its rat’s nest It can be pre recorded or live demo.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

This is a test of the emergency description service.