47k Ohm ±5% 62.5mW Power Per Element Bussed 8 Resistor Network/Array ±200ppm/°C 1206 (3216 Metric), Convex, Long Side Terminals #commonpartslibrary #resistor #5x1206

Linear Voltage Regulator IC Positive Fixed 1 Output 600mA SOT-25 3.3V LDO AP2112K-3.3 The AP2112K-3.3TRG1 is a low dropout (LDO) linear voltage regulator designed to provide a stable 3.3V output from a higher input voltage. It is optimized for low noise, high power supply rejection ratio (PSRR), and low quiescent current, making it suitable for battery-powered and noise-sensitive applications. The device features current limiting and thermal shutdown protection, ensuring reliable operation under fault conditions. It is commonly used in portable electronics, RF modules, microcontroller power supplies, and other low-power systems. Key Features Fixed output voltage: 3.3V Output current: up to 600 mA Low dropout voltage: ~250 mV at 300 mA load High PSRR: up to 70 dB at 1 kHz Low quiescent current: typically 55 µA Stable with low ESR ceramic capacitors Built-in overcurrent protection Thermal shutdown protection Fast transient response Absolute Maximum Ratings Input Voltage (VIN): up to 6.5 V Output Current: Internally limited Operating Junction Temperature: -40°C to +125°C Storage Temperature: -65°C to +150°C Electrical Characteristics (Typical values unless otherwise specified) Output Voltage Accuracy: ±2% Dropout Voltage: 250 mV @ 300 mA 400 mV @ 600 mA Line Regulation: 0.05%/V Load Regulation: 0.2% Quiescent Current: 55 µA Shutdown Current: <1 µA PSRR: 70 dB @ 1 kHz 45 dB @ 10 kHz Pin Configuration (SOT-23-5 / SC-70-5) VIN – Input voltage GND – Ground EN – Enable (active high) NC – No connection VOUT – Regulated output (3.3V) Package Information Package Type: SOT-23-5 (TRG1 suffix indicates tape & reel) Mounting: Surface mount Small footprint suitable for compact PCB layouts Typical Applications Battery-powered devices Wireless modules (Wi-Fi, Bluetooth, RF) Microcontroller and FPGA power supplies Portable consumer electronics Sensor and analog circuits requiring low noise Compliance & Reliability RoHS compliant Lead-free package Designed for high reliability and long operational life #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LinearRegulator #VoltageRegulator

Slide Switch SPST 4A 125V Throuh Hole The L101011MS02Q is a single-pole, single-throw (SPST) miniature toggle switch designed for low-power switching applications. It features a compact panel-mount design with a durable actuator and reliable contact mechanism, making it suitable for control and signal switching in industrial, instrumentation, and consumer electronics. The switch provides a maintained (latching) ON-OFF function and is built for long mechanical and electrical life. Key Features SPST (Single Pole, Single Throw) configuration ON-OFF maintained switching function Miniature toggle actuator Panel mount design with threaded bushing Solder lug terminals for secure wiring High mechanical durability Compact form factor Mechanical Characteristics Mounting Type: Panel mount Actuator Type: Toggle lever Bushing Type: Threaded, with nut and washer Terminal Type: Solder lug Number of Poles: 1 Number of Throws: 1 Switching Function: ON-OFF (latching) Electrical Characteristics Rated Voltage: 125 VAC / 28 VDC Rated Current: 3 A @ 125 VAC, 6 A @ 28 VDC Contact Resistance: ≤ 20 mΩ (initial) Insulation Resistance: ≥ 1,000 MΩ Dielectric Strength: 1,000 VAC for 1 minute Material Specifications Housing: Thermoplastic or phenolic (manufacturer dependent) Actuator: Metal (nickel-plated brass) Contacts: Copper alloy with silver plating Terminals: Brass, tin-plated Environmental Specifications Operating Temperature Range: -30°C to +85°C Storage Temperature: -40°C to +85°C Mechanical Life Mechanical Life: ≥ 40,000 cycles Electrical Life: ≥ 10,000 cycles (at rated load) Typical Applications Control panels Power switching for small devices Instrumentation equipment Audio equipment Industrial and consumer electronics #commonpartslibrary #rocker #switch #spst

Connector Header Through Hole 6 position 0.100" Pin Header 1x06 2.54mm PinHeader 1x6 2.54mm The TSW-106-07-G-S is a through-hole vertical header designed for board-to-board and board-to-wire interconnection in electronic systems. It is part of a precision connector series known for high reliability, consistent mechanical alignment, and excellent electrical performance. The component is commonly used in applications requiring modular connectivity, prototyping flexibility, and secure signal routing between printed circuit boards or peripheral interfaces. Its design supports repeated mating cycles while maintaining stable contact integrity, making it suitable for both development and production environments. Functional Description This component functions as a single-row header that provides a direct electrical interface between a printed circuit board and a mating connector or cable assembly. It enables straightforward signal or power routing through plated pins that are soldered into the PCB. The vertical orientation allows perpendicular mating, supporting compact and efficient board layouts. The connector is designed to ensure proper alignment and retention during mating, reducing the risk of intermittent connections. Electrical Characteristics The header supports low-voltage signal transmission and moderate current levels typical of board-level interconnects. It offers low contact resistance to maintain signal integrity and efficient current flow. The contact system is designed to provide consistent electrical performance across repeated insertions, ensuring reliability in both signal and power applications. Mechanical Characteristics The component features a robust insulating housing that maintains pin alignment and structural integrity during handling and operation. The contact pins are fabricated from conductive material and plated to enhance durability, conductivity, and مقاومت to corrosion. The through-hole mounting style provides strong mechanical anchoring to the printed circuit board, improving resistance to mechanical stress and vibration. The design supports reliable mating with compatible connectors and ensures long service life. Environmental Characteristics The TSW-106-07-G-S is constructed using materials that provide stable performance under typical environmental conditions encountered in electronic assemblies. It is designed to withstand standard temperature ranges and environmental stresses such as humidity and mechanical handling, maintaining electrical and mechanical reliability over time. Applications This header is widely used in embedded systems, industrial electronics, development platforms, communication equipment, and general-purpose PCB interconnect applications. It is especially suited for designs requiring modular connectivity, easy assembly, and dependable signal transfer. Summary The TSW-106-07-G-S from Samtec is a reliable through-hole header solution that combines mechanical durability with stable electrical performance. Its straightforward design, compatibility with standard interconnect systems, and suitability for a wide range of applications make it a common choice for board-level connectivity in modern electronic designs. #CommonPartsLibrary #Connector #Header #TSW

Slide Switch, SPDT, On-On, Through Hole, OS Series, 100mA # OS102011MS2QN1 ## General Description The OS102011MS2QN1 is a miniature slide switch manufactured by C&K, designed for low-power signal switching and control applications in electronic equipment. The switch features a compact mechanical design, reliable contact performance, and through-hole mounting configuration, making it suitable for embedded systems, industrial controls, instrumentation, telecommunications equipment, consumer electronics, and portable devices. Its robust construction ensures dependable operation throughout repeated switching cycles while maintaining stable electrical performance. The device is commonly utilized for mode selection, power control, configuration settings, and user-interface functions within electronic assemblies. ## Key Features ### Mechanical Characteristics * Miniature slide switch construction * Through-hole PCB mounting * Compact form factor * Durable actuator mechanism * Positive switching action * Designed for repeated mechanical operation ### Switching Characteristics * Maintained-contact operation * Reliable position retention * Low-force actuation * Stable contact engagement * Suitable for signal and control switching applications ### Electrical Characteristics * Low contact resistance * Reliable signal transmission * Stable switching performance * Suitable for low-current and low-voltage circuits * Consistent electrical operation throughout service life ### Contact System * High-reliability contact materials * Corrosion-resistant contact surfaces * Long operational durability * Dependable electrical continuity ### Material Construction * High-strength thermoplastic housing * Industrial-grade metallic contacts * Durable actuator assembly * RoHS-compliant materials ### Environmental Characteristics * Suitable for commercial and industrial electronic equipment * Resistant to mechanical wear * Reliable performance under normal operating environments * Designed for long-term service reliability ### Application Areas * Embedded Systems * Industrial Control Equipment * Consumer Electronics * Test and Measurement Instruments * Communication Devices * Medical Electronics * Power Control Circuits * User Interface Controls * Configuration and Mode Selection Functions * Electronic Development Platforms ### Compliance * RoHS Compliant * Lead-Free Compatible * Industrial-Grade Switching Component ## Manufacturer C&K ## Product Family OS Series Miniature Slide Switches #OS102011MS2QN1 #CKSwitches #SlideSwitch #MiniatureSwitch #ElectronicSwitch #PCBSwitch #EmbeddedSystems #IndustrialElectronics #ControlSystems #ConsumerElectronics #HardwareDesign #ElectronicsEngineering #SignalSwitching #PCBAssembly #ElectronicComponents #commonpartslibrary #switch #slide #spdt

Bluetooth, WiFi 802.11b/g/n/ax, Bluetooth v5.4 Transceiver Module 2.4GHz Integrated, Chip Surface Mount Silicon Labs SiWG917 module is our lowest power Wi-Fi 6 plus Bluetooth LE 5.4, ideal for ultra-low power IoT wireless devices using Wi-Fi®, Bluetooth, Matter, and IP networking for secure cloud connectivity. It is optimal for developing battery operated devices that need long battery life. SiWG917 module includes an ultra-low power Wi-Fi 6 plus Bluetooth Low Energy (LE) 5.4 wireless CPU subsystem, and an integrated micro-controller (MCU) application subsystem, security, peripherals and power management subsystem all in a single 16 x 21.1 x 2.3 mm package. The wireless subsystem consists of a multi-threaded Network Wireless Processor (NWP) running up to 160 MHz, baseband digital signal processing, analog front end, 2.4 GHz RF transceiver and integrated power amplifier. The application subsystem consists of an ARM® Cortex®-M4 running up to 180 MHz, embedded SRAM, flash, ultra-low power sensor hub, and matrix vector processor. The ARM® Cortex®-M4 is dedicated for peripheral and application-related processing, while the NWP runs the wireless and networking stacks on independent threads, thus providing a fully integrated solution that is ready for a wide range of embedded wireless IoT applications. The modules come with modular radio type approvals for various countries, including USA (FCC), Canada (IC/ISED) and Japan (MIC), and are in compliance with the relevant EN standards (including EN 300 328 v2.2.2) for the conformity with the directives and regulations in EU and UK. KEY FEATURES • Wi-Fi 6 Single Band 2.4 GHz 20 MHz 1x1 stream IEEE 802.11 b/g/n/ax • Bluetooth LE 5.4 • Single chip Matter Over Wi-Fi Solution • ARM® Cortex® M4 Processor with FPU subsystem up to 180 MHz with rich set of Digital and Analog Peripherals. • Wi-Fi 6 Benefits: TWT for improved efficiency and longer battery life, MUMIMO/OFDMA for Higher Throughput, network capacity and low latency • Best in Class Device and Wireless Security • WLAN Tx power up to +17.5 dBm with integrated PA • Bluetooth LE Tx power up to +17 dBm with integrated PA • WLAN Rx sensitivity as low as -95.5 dBm • Wi-Fi 4 Standby Associated mode current: 71 μA @ 1-second listen interval • Embedded Flash option up to 8 MB/ optional external Flash up to 16 MB • Embedded PSRAM option up to 2 MB/ optional external PSRAM option up to 16 MB • Ultra-low power sensor hub peripherals • Matrix Vector Processor (MVP) • Embedded Wi-Fi, Bluetooth LE, Matter, and networking stacks supporting wireless coexistence • Three software-configurable MCU application memory options for sharing the RAM between the wireless, system, and application (192/256/320 KB) • Operating temperature: -40 to +85 ºC • Operating supply range: 3.0 to 3.63 V • Supply voltage for GPIOs: 1.71 to 3.63 V #WiFi6 #BluetoothLE54 #IoTModule #WirelessSoC #SiliconLabs #EmbeddedSystems #SmartHome #IndustrialIoT #LowPowerDesign #RFModule #ConnectedDevices #EdgeComputing #MatterReady #PCBDesign #ElectronicsEngineering

Temperature Sensor Digital, Local -55°C ~ 150°C 16 b 6-WSON (2x2) The TMP117AIDRVR is a high-precision digital temperature sensor manufactured by Texas Instruments. The device provides accurate temperature measurements through an I²C-compatible digital interface and is optimized for applications requiring medical-grade accuracy, low power consumption, and compact PCB footprint. The sensor integrates a precision temperature sensing element, analog-to-digital converter, calibration memory, and digital interface into a single compact package. The device supports continuous conversion and shutdown operating modes, enabling efficient thermal monitoring in battery-powered and always-on systems. Internal calibration minimizes external component requirements while providing highly linear and repeatable temperature measurements across an extended operating range. The TMP117AIDRVR is commonly used in industrial controls, wearable electronics, healthcare equipment, environmental monitoring systems, battery management systems, consumer electronics, and precision instrumentation. Electrical Characteristics Supply voltage supports low-voltage digital systems and portable electronics applications. Ultra-low operating current enables long battery life in energy-sensitive designs. Integrated EEPROM allows programmable offset correction and configuration storage. Digital output eliminates the need for external ADC circuitry. High measurement resolution supports precision thermal monitoring applications. Low self-heating characteristics improve measurement stability and accuracy. Functional Features High-accuracy digital temperature sensing. I²C and SMBus compatible communication interface. Programmable alert functionality for thermal threshold monitoring. Continuous conversion and low-power shutdown operating modes. Integrated non-volatile memory for user configuration storage. Wide operating temperature range for industrial and commercial environments. Fast conversion timing suitable for real-time monitoring systems. Factory-calibrated performance requiring minimal external calibration. Package Information Package type is WSON with compact surface-mount footprint suitable for dense PCB layouts. Moisture-sensitive package designed for automated assembly processes. Lead-free and RoHS-compliant construction. Typical Applications Medical thermometers and patient monitoring systems. Industrial temperature monitoring equipment. Battery-powered portable electronics. HVAC and environmental sensing systems. Data acquisition and instrumentation systems. Server and embedded thermal management applications. Consumer electronics requiring precision thermal sensing. #commonpartslibrary #integratedcircuit #temperaturesensor

Red, Green, Blue (RGB) 624nm Red, 525nm Green, 470nm Blue LED Indication - Discrete 2V Red, 3.3V Green, 3.3V Blue 4-SMD, No Lead # 150080M153000 ## General Description The 150080M153000 is a compact surface-mount full-color RGB LED manufactured by Würth Elektronik as part of the WL-SFCD series. The device integrates red, green, and blue light-emitting elements within a single package, enabling the generation of a wide spectrum of colors for status indication, user interfaces, backlighting, visual notifications, and decorative lighting applications. Its diffused lens design provides uniform light distribution and wide viewing visibility, making it suitable for industrial equipment, consumer electronics, communication devices, instrumentation systems, control panels, and embedded electronic products. The component is optimized for automated assembly processes and offers reliable optical performance, low power consumption, and long operational life. ## Key Features ### Optical Characteristics * Full-color RGB light output * Integrated red, green, and blue emitters * Diffused lens design for uniform illumination * Wide viewing angle * High-visibility indication capability * Consistent color performance ### Electrical Characteristics * Low-power operation * Stable optical output * Suitable for indicator and backlighting applications * Reliable performance across operating conditions * Optimized for embedded electronic systems ### Mechanical Characteristics * Surface-mount package construction * Compact footprint * Low-profile package design * Compatible with automated assembly processes * Reflow-soldering compatible ### Package Construction * Common-anode configuration * Integrated multi-die LED architecture * Rectangular lens geometry * Lead-free package design * Industrial-grade construction ### Material Characteristics * High-quality encapsulation materials * Diffused optical lens * RoHS-compliant construction * Environmentally compliant materials ### Environmental Characteristics * Suitable for commercial and industrial applications * Long operational service life * Reliable operation under standard environmental conditions * Resistant to normal assembly and handling processes ### Application Areas * Status Indicators * User Interface Displays * Industrial Control Panels * Consumer Electronics * Home Appliances * Telecommunications Equipment * Instrumentation Systems * Backlighting Applications * Smart Devices * Embedded Electronic Products * Safety and Security Equipment * Human-Machine Interface Systems ### Compliance * RoHS Compliant * REACH Compliant * Lead-Free Compatible * Industry-Standard Surface-Mount Technology ## Manufacturer Würth Elektronik ## Product Family WL-SFCD SMD Full-Color Chip LED Series #150080M153000 #WurthElektronik #RGBLED #SMDLED #WLSFCD #FullColorLED #LEDIndicator #Backlighting #Optoelectronics #EmbeddedSystems #IndustrialElectronics #ConsumerElectronics #PCBDesign #ElectronicsEngineering #SMTAssembly #commonpartslibrary #optoelectronic #ledindication

Remote Receiver Sensor 38.0kHz 45m Through Hole This IR receiver series is optimized for long burst remote control systems in different environments. The customer can chose between different IC settings (AGC variants), to find the optimum solution for his application. The higher the AGC, the better noise is suppressed, but the lower the code compatibility. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. These components have not been qualified to automotive specifications. Individual IC settings to reach maximum performance • Immunity against noise (lamps, LCD TV, Wi-Fi) • Low supply current • Photo detector and preamplifier in one package • Supply voltage: 2.0 V to 5.5 V VS1838B #CommonPartsLibrary #Sensor #Transducer #Optical-Sensor #Photo-Detectors #Remote-Receiver #TSOP38238

Telecom Relay DPDT (2 Form C) Through Hole The G6K-2P-Y DC5 is a compact, ultra-miniature signal relay designed for high-density PCB mounting applications. Manufactured by Omron, this relay features a DPDT (2 Form C) contact configuration and operates with a 5 VDC coil. It is optimized for switching low-level signals and is commonly used in telecommunications, test and measurement equipment, and consumer electronics where space-saving and high reliability are critical. Key Features Ultra-miniature, low-profile design for high-density mounting DPDT (2 Form C) contact configuration High sensitivity coil (low power consumption) Gold-clad contacts for low-level signal switching High reliability and long mechanical life Fully sealed construction (flux protection) Suitable for surface-mount and through-hole variants (depending on suffix) Electrical Characteristics Coil Specifications Rated Coil Voltage: 5 VDC Coil Resistance: ~125 Ω Coil Current: ~40 mA Power Consumption: ~200 mW Must Operate Voltage: ≤ 75% of rated voltage Must Release Voltage: ≥ 10% of rated voltage Contact Specifications Contact Configuration: DPDT (2 Form C) Contact Material: Gold-clad silver alloy Contact Rating: 1 A at 30 VDC 0.5 A at 125 VAC Maximum Switching Voltage: 125 VAC / 60 VDC Maximum Switching Current: 1 A Maximum Switching Power: 30 W (DC) 62.5 VA (AC) Timing Characteristics Operate Time: ≤ 3 ms Release Time: ≤ 3 ms Insulation Characteristics Insulation Resistance: ≥ 1,000 MΩ (at 500 VDC) Dielectric Strength: Between Coil and Contacts: 1,000 VAC (1 min) Between Open Contacts: 500 VAC (1 min) Mechanical Characteristics Mounting Type: Through-hole (Y variant, PCB terminal) Weight: ~1 g Enclosure: Sealed (flux-resistant) Environmental Specifications Operating Temperature Range: -40°C to +70°C Storage Temperature Range: -40°C to +85°C Vibration Resistance: 10 to 55 Hz, 1.5 mm double amplitude Shock Resistance: 1,000 m/s² Life Expectancy Mechanical Life: ≥ 100 million operations Electrical Life: ≥ 100,000 operations (at rated load) Applications Telecommunications equipment Test and measurement instruments Audio signal routing Industrial control systems Consumer electronics Package Information Manufacturer: Omron Electronics Series: G6K Part Number: G6K-2P-Y DC5 #commonpartslibrary #relay

1/1 Transceiver Half RS422, RS485 8-SOIC These devices have robust 3.3-V drivers and receivers in a small package for demanding industrial applications. The bus pins are robust to ESD events with high levels of protection to Human-Body Model and IEC Contact Discharge specifications. Each of these devices combines a differential driver and a differential receiver which operate from a single 3.3-V power supply. The driver differential outputs and the receiver differential inputs are connected internally to form a bus port suitable for half-duplex (two-wire bus) communication. These devices feature a wide common-mode voltage range making the devices suitable for multi-point applications over long cable runs. These devices are characterized from –40°C to 125°C 1• Small-size VSSOP Packages Save Board Space, or SOIC for Drop-in Compatibility • Bus I/O Protection – >±15 kV HBM Protection – >±12 kV IEC 61000-4-2 Contact Discharge – >±4 kV IEC 61000-4-4 Fast Transient Burst • Extended Industrial Temperature Range –40°C to 125°C • Large Receiver Hysteresis (80 mV) for Noise Rejection • Low Unit-Loading Allows Over 200 Connected Nodes • Low Power Consumption – Low Standby Supply Current: < 2 µA – ICC < 1 mA Quiescent During Operation • 5-V Tolerant Logic Inputs Compatible With 3.3-V or 5-V Controllers • Signaling Rate Options Optimized for: 250 kbps, 20 Mbps, 50 Mbps • Glitch Free Power-Up and Power-Down Bus Inputs and Outputs 2 Applications • Factory Automation • Telecommunications Infrastructure • Motion Control #SN65HVD75D #RS485 #RS422 #Transceiver #TexasInstruments #IndustrialCommunication #FactoryAutomation #MotionControl #TelecomInfrastructure #ESDProtection #HalfDuplex #InterfaceIC #EmbeddedSystems #IndustrialElectronics #DataCommunication

Rotary Encoder Incremental 24 Quadrature (Incremental) User Selectable 10 mA @ 5 VDC,-10 C to +70 C The PEC11J-9015F-S0024 is a compact surface-mount incremental rotary encoder from the Bourns PEC11J series, designed for user interface applications requiring precise rotational input and long operational life. It features a quadrature output with 24 pulses per revolution and includes an integrated momentary push-button switch, making it suitable for menu navigation, volume control, tuning systems, and industrial control panels. Its rugged metal shaft construction and high durability make it reliable for both consumer and professional electronic equipment. Key Features Incremental rotary encoder with 2-bit quadrature output 24 pulses per revolution (24 PPR) resolution Integrated momentary push-button switch Surface-mount gull-wing terminals Compact 12 mm encoder body Durable metal shaft and bushing Long rotational life of up to 100,000 cycles No detents for smooth continuous rotation Supports up to 60 RPM operating speed Operating temperature range: -10 °C to +70 °C IP40 rated enclosure Flatted shaft design for secure knob attachment Suitable for: Audio equipment Lighting consoles Consumer appliances Communication devices Test and measurement equipment Component Category #Sensor #Encoder #Transducer #PEC11J