16 channel relay that will allow you to control different types of electrical loads

Arduino Electrical Control Shield -Redundant Temp. Sense -Geometric Monitoring -Dual RS232 Communication -USB Communication -Dual Motor Control -5 24V Control Relays -15 10V Analog IO -22 24V Protected IO

Xiao could be a good way to mod your house or machines, with a simple relay controller to rule the wires.

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

This project is a Gesture Light Switch Relay Reference Design. It involves an STM32 microcontroller (STMicroelectronics) that interacts with an APDS-9960 sensor (Broadcom) to detect hand gestures. The gesture data is used to control a Toshiba TLP175A relay and an Everlight tri-color LED to switch the light and change colors, respectively. Power is supplied by a Diodes Incorporated's AP2112K-3.3TRG1 regulator. #referenceDesign #edge-computing #edgeComputing #stm #relay #sensors #reference-design

ESP32 8 Relay Board. Has onboard mains to 5V or can use the ESP VIN for the +5V. 8 onboard relays capable of switching about 5A without adding additional tin to the traces.

Relay based on ESP8266 Max current ------- 15A Max Voltage ------- 250V #relay #esp8266 #iot

2 channel relay module for arduino

This project is a Gesture Light Switch Relay Reference Design. It involves an STM32 microcontroller (STMicroelectronics) that interacts with an APDS-9960 sensor (Broadcom) to detect hand gestures. The gesture data is used to control a Toshiba TLP175A relay and an Everlight tri-color LED to switch the light and change colors, respectively. Power is supplied by a Diodes Incorporated's AP2112K-3.3TRG1 regulator. #referenceDesign #edge-computing #edgeComputing #stm #relay #sensors #reference-design

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

16 channel relay that will allow you to control different types of electrical loads

12–24 VDC GPS-fix-controlled dual relay board. Relays switch immediately based on valid GPS fix status and provide SPDT contacts for 12/24 V loads up to 3 A with external GPS antenna support.

Swiftlane SRB Lite relay controller layout under production cleanup. Updated board-level rules to conservative manufacturable defaults (0.15 mm min trace and keep out, 0.25 mm board inset, explicit preferred widths) and audited remaining PCB blockers. Current blockers remain concentrated in overlapping copper, floating copper, and unrouted priority nets pending further interactive layout cleanup and re-route passes.

Demo Transistor Switch Relay | Forked Design

Welcome to your new project. Imagine what you can build here.

Template for Arduino Uno R3 Shield. Include an official pinout so you will always know Arduino names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Arduino Uno R3 itself along with the board outline on the silkscreen. #Arduino #Uno #Shield #Template #project-template #project

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Designing a Tractive System Active light(TSAL) circuit for an Electric Vehicle which does the following operations 1. The TSAL itself must have a red light, flashing continuously with a frequency between 2 Hz and 5 Hz and a duty cycle of 50%, active if and only if the LVS is active and the voltage across DC-link capacitors exceeds half the nominal TS voltage 2. The TSAL itself must have a green light, continuously on, active if and only if the LVS is active and ALL of the following conditions are true: ● All AIRs are opened. ● The pre-charge relay is opened. ● The voltage at the vehicle side of the AIRs inside the TSAC does not exceed 60 VDC or 50 VAC RMS. This schematic will include only the Green Light logic. We have to take proper care of High voltage and Low voltage isolation in this schematic because it will have to be implemented on the PCB as well.

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

The Arduino Uno learner's kit with ESP32 is a versatile educational tool for beginners. It combines an Arduino Uno board with additional components like a 2-channel motor driver, 7-segment display, relay outputs, programmable LEDs, push buttons, and analog inputs. This kit enables learners to explore electronics, programming, robotics, home automation, and more. With the ESP32 module, Wi-Fi and Bluetooth connectivity are possible, expanding the range of projects. It's a comprehensive package that fosters creativity and knowledge in the exciting world of electronics and programming. #arduino #esp32

5V Trigger Relay Module For Arduino And Raspberry Pi 5V Trigger Relay Module For Arduino And Raspberry Pi