Electronic Fuse Regulator 5.3A 20-WQFN (3x4) The TPS25940LRVCR is a compact eFuse (electronic fuse) power management IC from Texas Instruments designed to provide advanced power-path protection and load management for systems such as SSDs, servers, storage devices, and embedded electronics. It integrates protection features like overcurrent limiting, reverse current blocking, overvoltage protection, and controlled startup sequencing into a single chip. Wide input voltage range: 2.7 V to 18 V Adjustable current limit: 0.6 A to 5.3 A Low ON resistance: 42 mΩ typical True reverse current blocking using back-to-back MOSFETs Programmable output slew rate (dV/dt control) for inrush current management Overvoltage and undervoltage protection Fault and Power-Good outputs for system monitoring Current monitor (IMON) output Low-power DevSleep support for SSD applications Fast reverse voltage shutdown (~1 µs) Operating temperature: −40°C to +125°C junction temperature Available in a compact 20-pin WQFN package Typical Applications PCIe / SATA / SAS SSDs and HDDs Enterprise servers and storage systems RAID controller cards Smart load switches Set-top boxes and gaming systems Backup power and holdup capacitor systems Component Category This component belongs to: Power Management IC (PMIC) More specifically: eFuse / Hot-swap / Load Switch IC Package Information Package type: 20-WQFN (3 mm × 4 mm) Mounting type: Surface Mount (SMD) #commonpartslibrary #integratedcircuit #powermanagement #currentregulation

General Purpose Amplifier 2 Circuit, Dual, High Speed, Programmable, Current Mode (Norton) Amplifiers 14-SOIC

Artix-7 Field Programmable Gate Array (FPGA) IC 285 4976640 101440 484-BBGA #CommonPartsLibrary #IntegratedCircuit #Embedded #Gate-Array

LED Driver IC 16 Output Linear PWM Dimming 25mA 5.5V 28-TSSOP PCA9685PW,118 is a 16-channel, 12-bit PWM LED controller with an I²C interface designed for LED dimming, RGB/RGBA lighting, and servo motor control applications. It provides independent PWM control for up to 16 outputs, allowing precise brightness or position control while minimizing MCU GPIO usage. The device supports Fast-mode Plus I²C communication up to 1 MHz and operates from a 2.3 V to 5.5 V supply range. It is commonly used in robotics, LED backlighting, automation systems, and PWM expansion modules for microcontrollers such as Arduino, ESP32, and Raspberry Pi. Key Features 16 independent PWM output channels 12-bit PWM resolution (4096 steps) Programmable PWM frequency from approximately 24 Hz to 1526 Hz I²C Fast-mode Plus compatible interface up to 1 MHz Six hardware address pins allowing up to 62 devices on one I²C bus Programmable open-drain or totem-pole outputs Output capability: 25 mA sink current 10 mA source current Internal 25 MHz oscillator with optional external clock input Individual programmable LED ON/OFF timing for reduced EMI and current surges Supports software reset and group addressing (All Call/Sub Call) 5.5 V tolerant inputs and outputs Operating voltage range: 2.3 V to 5.5 V Package: 28-pin TSSOP (PW suffix) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LEDdriver

Linear Voltage Regulator IC Positive 0V to 15V Programmable Output 500mA 12-MSOP #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LinearRegulator #VoltageRegulator

Amplifier IC 2 Channel (Stereo) Class D 32-HTSSOP The TPA3116D2QDADRQ1 is an automotive-grade, high-efficiency Class-D stereo audio power amplifier IC from Texas Instruments. It is designed to drive speakers directly in compact audio systems while maintaining high output power and low heat dissipation. The device is part of the TPA3116-Q1 family, qualified for AEC-Q100 automotive applications, making it suitable for harsh environments such as vehicle infotainment and industrial audio systems. It operates from a single supply and uses advanced Class-D switching architecture to achieve high efficiency (typically >90%), reducing the need for large heat sinks and improving overall system power efficiency. 🔑 Key Features Output power capability Up to 2 × 50 W into 4 Ω (BTL mode at ~21 V) Wide supply voltage range 4.5 V to 26 V single supply operation High efficiency Class-D operation 90% efficiency with low idle power loss Stereo and mono configurations Supports BTL stereo and PBTL mono modes Differential and single-ended inputs Flexible audio input compatibility Advanced protection features Overvoltage protection Undervoltage protection Overtemperature shutdown Short-circuit protection DC detect protection with fault reporting EMI-optimized design Reduced electromagnetic interference for easier system compliance Programmable power limit Helps protect speakers and manage output levels Thermally enhanced 32-pin HTSSOP package Designed for better heat dissipation in compact layouts Typical Applications Automotive infotainment systems Car audio amplifiers Soundbars and home audio systems Portable and powered speakers Industrial audio solutions #commonpartslibrary #integratedcircuit #linearamplifier #audioamplifier

Spartan®-7 Field Programmable Gate Array (FPGA) IC 250 2764800 52160 484-BGA #CommonPartsLibrary #IntegratedCircuit #FPGAs #Spartan®-7 #XC7S50

Cyclone® IV E Field Programmable Gate Array (FPGA) IC 91 276480 6272 144-LQFP Exposed Pad Cyclone® IV E Field Programmable Gate Array (FPGA) IC 91 276480 6272 144-LQFP Exposed Pad #commonpartslibrary #integratedcircuit #fpga

RP2040 chip for Raspberry Pi Pico - ARM® Cortex®-M0+ MCU 32-Bit The RP2040 is a high-performance, low-cost microcontroller built around two ARM Cortex-M0+ cores. It is optimized for flexibility, ease of use, and deterministic real-time performance. Unlike many microcontrollers, it includes a unique programmable I/O subsystem (PIO), allowing custom hardware interfaces without extra components. Key Features Processing Dual-core ARM Cortex-M0+ processors Up to 133 MHz clock speed Efficient integer performance with low power consumption Memory 264 KB on-chip SRAM External QSPI flash support (typically 2 MB–16 MB depending on board) Programmable I/O (PIO) 2 PIO blocks, each with 4 state machines Enables custom protocols (e.g., SPI, I2C, UART, WS2812, VGA, etc.) Offloads timing-critical tasks from CPU 🔗 Connectivity Interfaces 2× UART 2× SPI 2× I2C USB 1.1 controller (device or host support) 16× PWM channels Analog Features 12-bit ADC (up to 5 channels, including internal temperature sensor) Power & Voltage Operating voltage: 1.8V – 3.3V Low-power modes available Package Options QFN-56 (7×7 mm) Development Ecosystem Supports C/C++ SDK MicroPython and CircuitPython support Strong community and documentation Typical Applications Embedded systems and IoT devices Robotics and automation DIY electronics and prototyping USB devices (HID, MIDI, etc.) Custom communication interfaces using PIO #CommonPartsLibrary #IntegratedCircuit #Microcontroller

20V High Efficiency Nanopower Step-Down Regulator Programmable 2.8V, 3V, 3.3V, 5V 1 Output 50mA 10-DFN #CommonPartsLibrary #IntegratedCircuits #BatteryChargers #LTC3388

MCP3913 Series 3.6 V 4.5 mA SMT Six-Channel Analog Front End - SSOP-28 The MCP3913A1T-E/SS is a high-performance, multi-channel analog front-end (AFE) from Microchip Technology intended for precision measurement applications. It features six simultaneous sampling 24-bit delta-sigma ADCs with integrated programmable gain amplifiers, enabling accurate acquisition of low-level analog signals. Designed for energy monitoring and industrial sensing, the device provides low noise, high dynamic range, and flexible configuration. It supports SPI communication for efficient interfacing with microcontrollers and digital processing systems. Key Features Six simultaneous sampling 24-bit delta-sigma ADC channels Integrated programmable gain amplifiers per channel High signal-to-noise ratio and low distortion Programmable oversampling ratios for performance tuning Internal voltage reference with external reference option SPI-compatible digital interface Configurable data output formats and control registers Low power operation modes Electrical Characteristics Resolution: 24-bit Number of Channels: 6 Input Configuration: Differential Supply Voltage: 2.7V to 3.6V Operating Temperature Range: -40°C to +125°C Programmable Gain: Up to 32 V/V (typical) Reference Voltage: Internal or external selectable Functional Description The device integrates six high-resolution delta-sigma ADCs that sample input signals simultaneously, ensuring accurate phase and timing relationships across channels. Each input passes through a programmable gain stage, allowing optimization for different sensor levels. Analog signals are digitized using oversampling and digital filtering techniques to achieve high precision and noise reduction. Configuration is handled via internal registers, and data is transferred through an SPI interface. Package Information Package Type: SSOP Pin Count: 28 Mounting Type: Surface Mount Applications Energy metering Power monitoring systems Industrial automation Multi-channel data acquisition Sensor interfacing Smart grid systems Advantages High integration reduces external components Simultaneous sampling improves measurement accuracy High resolution supports precise signal analysis Flexible configuration for various system requirements #commonpartslibrary #integratedcircuit #powermanagement #energymetering

Certus™-NX Field Programmable Gate Array (FPGA) IC 150 1548288 39000 196-LFBGA #commonpartslibrary #integratedcircuit #certus #fpga

Audio D/A Converter ICs SABRE 8 Channel Smart DAC with Line Drivers, ASP2, 7mmx7mm, 48-QFN The ES9082Q is a high-performance stereo digital-to-analog converter (DAC) developed by ESS Technology for premium audio applications requiring exceptional sound quality, low power consumption, and compact integration. It utilizes the patented HyperStream® architecture and Time Domain Jitter Eliminator technology to deliver highly accurate audio reproduction with ultra-low distortion and noise characteristics. The device supports high-resolution PCM and DSD audio formats, making it suitable for portable audio devices, USB DACs, digital media players, automotive infotainment systems, wireless audio products, and professional audio equipment. The ES9082Q integrates advanced digital filtering, low-jitter clock management, and flexible audio interface support while maintaining efficient power operation for battery-powered applications. Designed for compact embedded audio systems, the ES9082Q provides excellent dynamic range and signal fidelity while minimizing external component requirements. Its architecture enables high-quality playback performance across a wide range of consumer and industrial audio applications. Electrical Characteristics Supply voltage supports low-voltage digital and analog power domains optimized for portable and embedded applications. The device operates with low power consumption while maintaining high audio performance. Integrated power management supports efficient system-level implementation. Audio Performance The converter supports high-resolution stereo audio output with advanced oversampling and noise shaping technology. It delivers ultra-low total harmonic distortion plus noise performance and high dynamic range suitable for high-fidelity audio playback systems. PCM audio data rates support standard and high-resolution formats up to 32-bit depth with sampling frequencies extending to high-definition audio ranges. Native DSD playback capability is also supported for audiophile-grade applications. Digital Audio Interface The ES9082Q supports industry-standard serial audio interfaces including I²S, left-justified, and related digital audio communication protocols. Flexible master and slave clocking configurations enable compatibility with a wide variety of host processors and audio controllers. Integrated jitter suppression circuitry improves clock stability and minimizes timing-induced audio artifacts. Integrated Features The device incorporates digital interpolation filters, volume control functions, soft mute capability, and programmable audio processing features. Internal PLL and clock management circuitry reduce external timing component requirements. Built-in low-noise analog output stages simplify audio signal chain design and reduce overall PCB footprint. Package Information The ES9082Q is provided in a compact surface-mount package optimized for space-constrained audio products. The package supports automated assembly and high-density PCB layouts commonly used in portable and embedded systems. Typical Applications Applications include portable audio players, USB DAC modules, wireless speakers, automotive audio systems, headphones, digital amplifiers, embedded multimedia devices, smart home audio equipment, and professional audio playback systems. #commonpartslibrary #integratedcircuit #audioic #dac #stereodac #esstechnology #es9082q #highresolutionaudio #audiophile #digitalaudio #analogaudio #i2s #dsd #pcm #embeddedaudio #consumerelectronics #portableaudio #usbdac #hifi #signalprocessing #lownoise #lowdistortion #electronicsdesign #pcbdesign #hardwareengineering #electroniccomponents #semiconductor #mixedsignal #audioelectronics #soundquality

Delay Line IC Programmable 1024 Tap 3.2ns ~ 14.8ns 32-TQFP #commonpartslibrary #integratedcircuit #delayline #programmable

iCE40™ LP Field Programmable Gate Array (FPGA) IC 21 384 32-VFQFN Exposed Pad #CommonPartsLibrary #IntegratedCircuit #Embedded #FPGAs #ICE40