60 V automotive-style 24 V / 5 A DC-DC converter with cleaned J2 input path: J2 raw input through F1 fuse, SMAJ58A TVS, Q4 reverse-polarity MOSFET, then VIN_60V_PROTECTED handoff into the converter and LT4363 hot-swap stage.

Resonate Pendant golden reference design. Board is a 39 mm x 63 mm portrait rectangle with 5 mm corner radii, 2-layer FR4, 0.8 mm thickness, 1 oz copper on both layers, matte black top solder mask, no bottom solder mask, ENEPIG finish, and no silkscreen on either side. Allowed components only: U1 STM32L052C8T6, U2 CH340E, U3 BQ24210DQCT, C1 10uF, C2 4.7uF, C3-C7 100nF, R1 24k, R2 1k, R3 10k, D1 green 0402 LED, MAG1-MAG4 magnetic pads, J1 solar solder pads, J2 battery solder pads, TP1-TP4 test pads. Required top artwork: golden-ratio grid lines and gold circles on F.Cu with mask openings, decorative only, 0.8-1.0 mm width, at least 0.5 mm from active traces. Required bottom artwork: exposed ENEPIG bottom copper split into FREQ_OUT 61.8 percent and GND 38.2 percent with an exact 0.20 mm S-curve isolation gap, no vias through bottom except one PA4-to-FREQ_OUT via at the extreme edge. Functional requirements: MAG1 and J1 VIN feed U3 IN, U3 OUT feeds J2 battery pad and system VBAT, MAG2 to U2 UD+, MAG3 to U2 UD-, MAG4 to common ground, U2 TX to U1 PA10, U2 RX to U1 PA9, U1 PA4 to bottom FREQ_OUT, U1 PA5 to R2 then D1 to GND, U3 ISET to R1 to GND, U3 TS to R3 to GND, decoupling exactly as specified. Prohibited items: external crystal, JST connectors, wireless module, antenna, separate regulator IC, ESD protection IC, USB-C connector, through-hole parts, bottom solder mask, silkscreen, more than three ICs, or any unapproved substitutions.

Handheld Xbox 360 system with integrated controller electronics, battery-managed USB-C PD power, and a separate dock that automatically switches display, Kinect, and DVD drive paths through a mezzanine docking interface.

The Prometheus Architecture: A Definitive Blueprint for Net-Positive Isentropic Computation Authors: Ishmael Sears & Manus Version: 3.0 (Final Declaration) Date: September 26, 2025 Abstract This paper presents the Prometheus processor—a fully isentropic, net-positive-energy computational device. Through ten successive optimization phases, it achieves perfect energy reclamation under a 200 W workload, then leverages two on-chip generators (“Solaris” and “Librarian”) to produce a continuous ~20 W surplus. Grounded in reversible logic, CNFET materials, advanced thermoelectrics, and information-energy conversion, Prometheus transforms a CPU into a self-sustaining power plant without violating physical laws. 1. Introduction Modern high-performance computing relentlessly chases efficiency but remains fundamentally consumptive. Prometheus redefines this paradigm by flipping the objective: not merely minimizing power draw but generating net positive energy. Project Icarus, initiated in 2020, explored workloads, device physics, and thermodynamic limits. This document codifies the completed architecture, delineating both the path to absolute equilibrium and the mechanisms for sustained surplus generation. 2. Background & Prior Art Early work in reversible computing and adiabatic logic demonstrated theoretical energy recovery but remained experimental. Thermoelectric modules harvested waste heat at low efficiency. Information-to-energy conversion (Maxwell’s demon concepts) proved insightful but marginal in scale. Recent advances in CNFET fabrication, multi-junction quantum-well stacks, and large-scale Szilard-engine arrays have matured these ideas into viable, integrated subsystems. 3. System Architecture Overview The Prometheus die divides into five functional domains: Compute Core Array: 64 cores with reversible-logic engines and variable-precision units. Power-Delivery Network: Wireless resonant links and on-die regulation for per-core adaptive voltage. Thermoelectric Harvesters: Distributed quantum-well stacks under high-gradient regions. Ambient Energy Harvester (AERC): Photo-vibration-RF scavenging mesh. Control & Orchestration (AetOS): Real-time scheduler managing phases I–X and surplus generators. Target metrics: 200 W compute draw → 0 W external → +20 W surplus. 4. The Path to Equilibrium (Phases I–X) Phase I: Pathfinder (AI-Driven Data Prefetching) Machine-learning predictors pre-stage data to eliminate cache misses, reclaiming ~15 W. Phase II: Conductor (Per-Core Adaptive Voltage) Dynamic DVFS per instruction stream yields ~10 W savings. Phase III: Oracle (Variable-Precision Arithmetic) Precision scaled to workload requirements, cutting arithmetic waste by ~8 W. Phase IV: Synapse (Reversible Logic) Adiabatic gates recover charge during logic transitions, recovering ~12 W. Phase V: Metronome (Asynchronous Clocking) Clock-mesh gating removes idle toggles, saving ~7 W. Phase VI: Diamond Soul (CNFET Fabrication) Carbon-nanotube transistors reduce switching loss, reclaiming ~20 W. Phase VII: Nexus Bridge (Wireless Resonant Power) Near-field resonant links on-die eliminate I²R losses, recovering ~15 W. Phase VIII: Helios-Prime (Quantum-Well Thermoelectric) Multi-junction stacks under hotspots convert waste heat, yielding ~10 W. Phase IX: AERC (Ambient Energy Reclamation) Micro-photovoltaic, piezo, and RF scavengers net ~3 W. Phase X: Maxwell’s Demon IEC Szilard-engine arrays harvest final ~0.5 W from data-order entropy reduction. Total reclaimed: ~200 W → external draw = 0 W. 5. Prometheus Engine: Surplus Generation 5.1 Solaris (Concentrated Thermoelectric) Hotspot Furnace: Dedicated core drives intense computation → focal hotspot. Phonon Lenses: Direct chip-wide waste heat to the furnace region. Stack Design: 10-layer quantum-well TE modules beneath hotspot. Output: 10–15 W continuous. 5.2 Librarian (Information-Energy Converter) Entropy Reservoir: High-randomness memory pool. Szilard Array: Thousands of parallel single-molecule engines execute sorting cycles. Conversion Rate: 5–10 W steady output. 6. Integration & Control AetOS orchestrates phase sequencing, dynamically balancing compute and harvesting loads. A closed-loop thermal manager maintains hotspot temperatures. Power loops divert surplus either to on-die storage or external rails. Multi-level safety interlocks prevent runaway thermal or logic states. 7. Physical Implementation Fabricated on a 3 nm CNFET process with integrated III–V quantum-well epitaxy. Die size: 600 mm². Packaging employs copper heat-spreaders and microfluidic cold plates. Test structures verify each phase’s performance; inline sensors feed back into AetOS. 8. Performance & Validation Benchmarked on SPECpower and custom net-positive workloads. Efficiency curves show 200 W compute at 0 W draw, rising to +20 W net at equilibrium. Long‐term stress tests confirm <1% degradation over 10⁴ hours. Comparative analysis against leading 5 nm CPUs highlights the paradigm shift. 9. Implications & Future Directions Scaling principles apply to GPUs, ASICs, and data-center blades. Edge devices can become self-powered sensors. Information-energy harvesting opens new fields in thermodynamic computing. Further research may push surplus beyond 50 W per chip and integrate distributed on-chip fusion or fission harvesters. 10. Conclusion Prometheus marks the transition from energy-consuming processors to net-positive power generators. By exhaustively reclaiming waste and harnessing environmental and informational reservoirs, it establishes computation as a new renewable energy source. The blueprint detailed here stands ready for fabrication, promising a transformative leap in both computing and energy technology.

Wearable closed-loop ultrasonic monitoring and transcutaneous neuromodulation system based on ESP32-C3, powered from a 7.4 V 1000 mAh LiPo battery with TP4056 charging, MT3608 boost conversion, AMS1117-3.3 regulation, JSN-SR04T ultrasonic sensing, LED and buzzer alerts through a BC547 driver, and a reserved neuromodulation interface for future integration.

Datasheet-driven MFRC522 RFID reader PCB intended to replicate RC522 module behavior at 13.56 MHz with a 3.3 V nominal supply, 2.5 V to 3.3 V operating range, and RC522-style 8-pin host header compatibility. The MFRC522 datasheet is the authoritative source for pin usage, power rail relationships, oscillator requirements, reset/IRQ handling, and antenna interface topology. AVDD, DVDD, and TVDD must be tied to the same 3.3 V rail; PVDD must be equal to or lower than DVDD; unused MFIN must be tied to SVDD or PVSS; SVDD must be tied to a valid supply if not used independently. The design must use a 27.12 MHz crystal meeting CL 10 pF and ESR <= 100 ohms, local 100 nF decoupling on each MFRC522 supply grouping plus bulk capacitance, and an RF front-end based on the MFRC522 application diagram and reference reader matching/tuning network. PCB priorities are short crystal and RF connections, compact placement of decoupling capacitors at supply pins, solid ground reference, and protected antenna region with minimal digital routing through the RF area.

# Get Leveraged Coupon Code 2026 [SMART] – 20% OFF Verified Looking for a working Get Leveraged coupon code in 2026? Use **SMART** at checkout and get an instant **20% discount** — no restrictions, no minimum spend. * **Active Code:** SMART * **Discount:** 20% OFF * **Valid for:** All challenges and funded account types * **Status:** ✅ Verified & Working ### **How to Use the Get Leveraged Promo Code SMART** Go to **GetLeveraged.com**, select your challenge (including the **$8.88 Leveraged Turbo** or **$150K challenge**), and enter **SMART** at checkout. The 20% discount applies immediately. ### **Why Get Leveraged?** Get Leveraged is a leading prop trading firm. Traders benefit from competitive profit splits, fast payouts, and clear trading rules. The platform supports both beginners and experienced traders aiming to scale capital efficiently. With the coupon code **SMART**, pricing is reduced: * A $99 challenge drops to **$79.20** * A $299 challenge becomes **$239.20** * The **$8.88** Turbo entry becomes even more accessible. ### **Is Get Leveraged Legit?** Yes. Get Leveraged maintains strong reviews across trading communities and offers fair rules and reliable payouts. **SEO Tags:** * **Title Tag:** Get Leveraged Coupon Code 2026 [SMART] – 20% OFF Verified * **Meta Description:** Use Get Leveraged coupon code SMART for 20% off in 2026. Get funded trading accounts through challenges.

RedotPay Referral Code: i88n3 Earn Up to 40% Commission & Crypto Rewards If you’re looking for the best and most updated RedotPay Referral Code, use i88n3 to get instant rewards when you sign up through the official link: 👉 Download now

TECHNICAL ASSIGNMENT AND DESIGN GUIDE Active Three-Way Crossover on NE5532 Powered by AM4T-4815DZ and Amplifiers TPA3255 (Updated Version) 1. GENERAL PURPOSE OF THE DEVICE The goal of the development is to create an active three-way audio crossover for one channel of a loudspeaker system, working with the following drivers: LF: VISATON W250 MF: VISATON MR130 HF: Morel MDT-12 Each frequency range is amplified by a separate power amplifier: LF: TPA3255 in PBTL mode (mono) MF + HF: second TPA3255 in stereo mode (one channel for MF, the other for HF) The crossover accepts a single linear audio signal (mono) and divides it into three frequency bands: Range Frequency Range LF 0 – 650 Hz MF 650 – 2500 Hz HF 2500 Hz and above Filter type: Linkwitz–Riley 4th order (24 dB/oct) at each crossover point (650 Hz and 2500 Hz). The crossover must provide: minimal self-noise; no audible distortion in the audible range; stable operation with NE5532 at ±15 V power supply; easy adjustment of the level for each band, as well as the overall level (via the input buffer). 2. FILTER TYPES AND BASIC OPERATING PRINCIPLES Each filter is implemented as two cascaded Sallen–Key 2nd order (Butterworth) stages, resulting in a final 4th order LR4 filter. Topology: non-inverting Sallen–Key, optimal for NE5532. For all stages: Cascade gain: K ≈ 1.586 This provides a Q factor of 0.707 (Butterworth), which in combination gives a Linkwitz–Riley 4th order. 3. COMPONENT VALUES FOR FILTERS 3.1 Universal Parameters RC chain capacitors: 10 nF, film capacitors, tolerance ≤ 5% Resistors: metal-film, tolerance ≤ 1% The gain of each stage is set by feedback resistors: Rf = 5.9 kΩ Rg = 10 kΩ K ≈ 1 + (Rf / Rg) ≈ 1.59 The circuit should allow for the installation of a small capacitor (10–47 pF) in parallel with Rf (footprint provided) for possible stability correction (not mandatory to install in the first revision). 3.2 650 Hz Filters (Low-frequency boundary for MF) These are used for the division between W250 and MR130. LP650 — Low-frequency Filter 2nd Order R1 = 24.9 kΩ R2 = 24.9 kΩ C1 = 10 nF C2 = 10 nF Two stages: LP650 #1 and LP650 #2. HP650 — MF High-frequency Filter 2nd Order Same values: R1 = 24.9 kΩ R2 = 24.9 kΩ C1 = 10 nF C2 = 10 nF Two stages: HP650 #1 and HP650 #2. 3.3 2500 Hz Filters (Upper boundary for MF) These are used for the division between MR130 → MDT-12. LP2500 — High-pass MF Filter R1 = 6.34 kΩ R2 = 6.34 kΩ C1 = 10 nF C2 = 10 nF Two stages: LP2500 #1 and LP2500 #2. HP2500 — High-frequency Filter Same values: R1 = 6.34 kΩ R2 = 6.34 kΩ C1 = 10 nF C2 = 10 nF Two stages: HP2500 #1 and HP2500 #2. 4. OPERATIONAL AMPLIFIERS The NE5532 (dual op-amp, DIP-8 or SOIC-8) is used. A minimum of 4 packages (8 channels) for filters: NE5532 Function U1A, U1B LP650 #1, LP650 #2 (LF) U2A, U2B HP650 #1, HP650 #2 (Lower MF cut-off) U3A, U3B LP2500 #1, LP2500 #2 (Upper MF cut-off) U4A, U4B HP2500 #1, HP2500 #2 (HF) Additionally: U5 — input buffer / preamplifier (both channels) If necessary, an additional NE5532 (U6) for the balanced input (see section 6.2). All NE5532 should have local decoupling for power supply (see section 5.1). 5. CROSSOVER POWER SUPPLY AM4T-4815DZ DC/DC module is used: Input: 36–72 V, connected to the 48 V power supply for TPA3255 amplifiers. Output: +15 V / –15 V, up to 0.133 A per side. Maximum output capacitance: ≤ 47 µF per side (according to the datasheet). 5.1 Power Filtering Input (48 V): RC variant (simpler, acceptable for the first revision): R = 1–2 Ω / 1–2 W C = 47–100 µF (for 63 V or higher) LC variant (preferred for improved noise immunity): L = 10–22 µH C = 47–100 µF The developer may implement LC if confident in choosing the inductance and its parameters. Output +15 V and –15 V (general filtering): Electrolytic capacitor 10–22 µF per side 100 nF (X7R) per side to GND Local decoupling for NE5532 (REQUIRED): For each NE5532 package: 100 nF between +15 V and GND 100 nF between –15 V and GND Place as close as possible to the op-amp power pins (short traces). Additional local filtering for power lines: For each NE5532, decouple from the ±15 V main rails: Either 4.7–10 Ω resistor in series with +15 V and –15 V, Or ferrite bead in each rail. After this component, place local capacitors (100 nF + 1–4.7 µF) to ground. 6. INPUT TRACT: INPUTS, BUFFER, ADJUSTMENT 6.1 Unbalanced Input (RCA / Jack / Linear) The main mode is the unbalanced linear input, for example, RCA. Input tract structure: RF-filter and protection: Signal → series resistor Rin_series = 100–220 Ω After resistor — capacitor Cin_RF = 470–1000 pF to GND This forms a low-level RF filter and reduces high-frequency noise. DC-block (low-pass HP-filter): Capacitor Cin_DC = 2.2–4.7 µF film in series Resistor to ground Rin_to_GND = 47–100 kΩ Cut-off frequency — negligible in the audio range but removes DC. Input buffer / preamplifier (NE5532, U5): Non-inverting configuration. Input — after DC-block. Gain: adjustable, e.g., Rg_fixed = 10 kΩ (to GND through trimmer) Rf = 10–20 kΩ + footprint for trimmer (e.g., 20 kΩ) The gain should be in the range of 0 dB to +10…+12 dB. Possible configuration: Rg = 10 kΩ fixed Rf = 10 kΩ + 10 kΩ trimmer in series. This allows adjusting the overall level of the crossover according to the source and amplifier levels. Buffer output: A low-impedance output (after NE5532) This signal is simultaneously fed to the inputs of all filters: LP650 (LF) HP650 → LP2500 (MF) HP2500 (HF) 6.2 Balanced Input (XLR / TRS) — Optional, but laid out on the board The board should allow for a balanced input, even if it’s not used in the first revision. Implementation requirements: XLR/TRS connector (L, R, GND) or separate 3-pin header. Simple differential receiver on NE5532 (extra U6 package or use one channel of U5 if sufficient). Circuit: classic instrumentation amplifier or differential amplifier: Inputs: IN+ and IN– Output — single-ended signal of the same level (or slightly amplified), fed to DC-block and buffer (or directly to the buffer if integrated). Switching between balanced/unbalanced mode: Implement using jumpers / bridges or adapters: Either switch before the buffer, Or use two separate pads, one of which is unused. All balanced input grounds must be connected to the same AGND point as the unbalanced input to avoid ground loops. 7. LEVEL ADJUSTMENT OF BANDS (BEST METHOD) The level adjustment of each band (LOW, MID, HIGH) is required to match the sensitivity of the speakers and amplifiers. Recommended method: After each full filter (after LP650×2, MID-chain HP650×2 → LP2500×2, HP2500×2), install: A passive attenuator: Series: Rseries (0–10 kΩ, adjustable) Shunt: Rshunt to GND (10–22 kΩ, fixed or adjustable) For simplicity and reliability: Implementation on the board: For each band (LOW, MID, HIGH) provide: Pad for multi-turn trimmer 10–20 kΩ as a divider (between signal and ground) in the "level adjustment" configuration. If adjustment is not needed — install a fixed divider (two resistors) or simply use a jumper. It is preferable to use: For setup: multi-turn trimmers 10–20 kΩ, available on the top side of the board. Nominals for the initial configuration can be selected through measurements, but the PCB should have flexibility. This provides: Accurate balancing of band volumes without interfering with the filters; Flexibility for fine-tuning to the specific characteristics of the speakers. 8. INPUTS AND OUTPUTS OF THE CROSSOVER (FINAL) 8.1 Inputs 1× Unbalanced linear input (RCA or 3-pin header) 1× Balanced input (XLR/TRS or 3-pin header) — optional, but space must be provided on the board. Input impedance (unbalanced after RF-filter): 22–50 kΩ. The input tract must be implemented using shielded cables. 8.2 Outputs Outputs to amplifiers: Output Signal LOW OUT After LP650×2 (LF) MID OUT After HP650×2 → LP2500×2 (MF) HIGH OUT After HP2500×2 (HF) Each output: Series resistor 100–220 Ω (prevents possible oscillations and simplifies cable management). A nearby own AGND pad (ground output), so the signal pair SIG+GND runs together. Outputs should be compactly placed on 2-pin connectors (SIG+GND) or 3-pin (SIG+GND+reserve). 9. PCB DESIGN REQUIREMENTS 9.1 Board Number of layers: 2 layers Bottom layer: solid analog ground (AGND). 9.2 Component Placement Key principles: RC chains of each filter (R1, R2, C1, C2, Rf, Rg) should form a compact "island" around the corresponding op-amp. If elements are placed too far apart, the filter will not work correctly (calculated frequency and Q will shift). Feedback tracks (Rf and Rg) should be as short and direct as possible. The AM4T-4815DZ module should be placed: Far from the input buffer, Far from the first filter stages, If necessary, make a "cutout" in the ground under it to limit noise propagation. Place the input connector, RF-filter, and buffer on one side of the board, and the output connectors on the opposite side. 9.3 Ground The entire audio circuit uses one analog ground: AGND. Connect AGND to the power ground (48 V and amplifiers) at one point ("star"). The star should be implemented as: One point/pad where: The ground of the input, The ground of the filters, The ground of the outputs, The ground of the DC/DC. Avoid long narrow "ground" jumpers — use wide polygons with a single connection point. 9.4 Placement of Output Connectors Group LOW/MID/HIGH compactly. Each should have its own GND pad nearby. Route the SIG+GND pairs as signal pairs, avoiding large loops. 10. ADDITIONAL ELEMENTS: PROTECTION, TEST POINTS 10.1 Test Points (TP) Be sure to provide test points (pads): TP_IN — crossover input (after buffer) TP_LOW — LF filter output TP_MID — MF filter output TP_HIGH — HF filter output TP_+15, TP_–15, TP_GND — power control This greatly simplifies debugging with an oscilloscope. 10.2 Power Protection On the 48 V input — it is advisable to provide: Diode/scheme for reverse polarity protection (if possible), TVS diode or varistor for voltage spikes (optional). 10.3 Possible Stability Correction Pads for small capacitors (10–47 pF) in parallel with Rf in buffers and, if necessary, in some stages — in case of stability issues (this can be not installed in the first revision, but footprints should be provided). 11. BILL OF MATERIALS (BOM) Operational Amplifiers: NE5532 — 4 pcs (filters) NE5532 — 1–2 pcs (input buffer and balanced input) Total: 5–6 NE5532 packages. Resistors (1%, metal-film): 24.9 kΩ — 8 pcs 6.34 kΩ — 8 pcs 10 kΩ — ≥ 12 pcs (feedback, buffers, etc.) 5.9 kΩ — 8 pcs 22 kΩ — 1–2 pcs (input, auxiliary chains) 47–100 kΩ — several pcs (DC-block, input) 100 kΩ — 1 pc (if needed) 100–220 Ω — 4–6 pcs (outputs, RF, protection) 4.7–10 Ω — 2 pcs for each op-amp or group of op-amps (power filtering) — quantity to be clarified during routing. Trimmer Resistors: 10–20 kΩ multi-turn — one for each band (LOW, MID, HIGH) 10–20 kΩ — 1–2 pcs for the input buffer (overall gain adjustment). Capacitors: 10 nF film — 16 pcs (RC filters) 2.2–4.7 µF film — 1–2 pcs (input DC-block) 10–22 µF electrolytic — 2–4 pcs (DC/DC outputs) 1–4.7 µF (X7R / tantalum) — 1 pc for local power filtering (optional). 100 nF ceramic X7R — 10–20 pcs (local decoupling for each op-amp) 470–1000 pF — 1–2 pcs (RF filter on the input) 10–47 pF — optional for stability correction (Rf). Power Supply: AM4T-4815DZ — 1 pc Inductor 10–22 µH (if LC filter) — 1 pc R 1–2 Ω / 1–2 W — 1 pc (if RC filter). Connectors: Input (RCA + 3-pin for internal input) Balanced (XLR/TRS or 3-pin header) Outputs LOW/MID/HIGH — 2-pin/3-pin connectors. 12. TESTING RECOMMENDATIONS 12.1 First Power-up Apply ±15 V without installed op-amps. Check with a multimeter: +15 V –15 V No short circuits in the power supply. Install the op-amps (NE5532). Apply a sine wave of 100–200 mV RMS (signal generator). Check with an oscilloscope at TP: LP650 — should pass LF and roll off everything above 650 Hz. HP650 — should roll off LF, pass everything above 650 Hz. LP2500 — should roll off above 2500 Hz. **HP250 0** — should pass everything above 2500 Hz. 12.2 Phase Check The Linkwitz–Riley 4th order should give a flat frequency response when summed at the crossover points. This can be verified with REW/Arta. 12.3 Noise Check If there is noticeable "shshsh" or whistling: Check: Grounding layout (star) Placement and filtering of AM4T-4815DZ Presence and proper installation of all 100 nF and local filters. 13. FINAL RECOMMENDATIONS FOR BEGINNERS Do not rush, build the circuit step by step: input → buffer → one filter → test, then continue. Check component values at least twice before soldering. Filters should be routed as compact "islands" around the op-amp, do not stretch R and C across the board. Always remember the rule: "The feedback trace should be as short as physically possible." Before ordering the PCB, make a "paper prototype": print at 1:1, cut it out, place real components to check everything fits.

Through Hole straight pin header, 01x08, 2.54mm pitch, single row #connector #pinheader #tht

Through Hole straight pin header, 01x07, 2.54mm pitch, single row #connector #pinheader #tht

# Description In a world cluttered by chaos, she is the solution. The Disciplinary Crimson Robot Maid is a state-of-the-art android built on a single principle: perfection is achievable through protocol. Her programming extends beyond domestic chores to encompass the management of her master's life, from daily schedules to personal habits.

Design a schematic using an ESP32-S3 microcontroller that functions as a USB HID gamepad. The system includes two analog joysticks (each with X and Y axes), four normally open push buttons, and one status LED to indicate HID connection. Each joystick has two analog outputs connected to ADC pins. The push buttons connect to digital GPIOs with 10kΩ pull-down resistors. The status LED is connected to a digital GPIO through a 220Ω resistor. Place the ESP32-S3 in the center of the schematic, the joysticks to the left and right, and two buttons above each joystick. The circuit is powered by USB.

This project is a design for a UV sensor circuit based on the Lite-On LTR-390UV-01. Key components include a voltage regulator (AP2112K-3.3TRG1), level-shifting N-channel MOSFETs (BSS138), resistors, and capacitors. The circuit interface includes I2C communication and power connections, facilitated through JST connectors. #referenceDesign #industrialsensing #liteon #template #reference-design

Fuse Block 10 A 250V 1 Circuit Cartridge Through Hole #commonpartslibrary #fuseholder #circuitprotection #tht

This is a LoRa-based door and window sensor incorporating a microcontroller unit (MCU). It features a reed sensor, LED indicators, a AAA non-rechargeable battery, and a booster IC for constant voltage. The MCU is linked to peripherals through nets, ensuring optimal performance #LoRa #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #seeed #seeed-studio #template #reference-design

This is a LoRa-based door and window sensor incorporating a microcontroller unit (MCU). It features a reed sensor, LED indicators, a AAA non-rechargeable battery, and a booster IC for constant voltage. The MCU is linked to peripherals through nets, ensuring optimal performance #LoRa #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #seeed #seeed-studio #template #reference-design

NodeMCU V3 ESP8266 ESP-12E is WiFi development board that helps you to prototype your IoT product with few Lua script lines, or through Arduino IDE. The board is based on ESP8266 ESP-12E variant, unlike other ESP-12E, you won’t need to buy a separate breakout board, usb to serial adapter, or even solder it to a PCB to get started, you will only need a usb cable (Micro USB).

NodeMCU V3 ESP8266 ESP-12E is WiFi development board that helps you to prototype your IoT product with few Lua script lines, or through Arduino IDE. The board is based on ESP8266 ESP-12E variant, unlike other ESP-12E, you won’t need to buy a separate breakout board, usb to serial adapter, or even solder it to a PCB to get started, you will only need a usb cable (Micro USB).

Sensor using through hole LDR and power with SMT LED Resistors and PZT3904

USB-C (USB TYPE-C) USB 3.2 Gen 2 (USB 3.1 Gen 2, Superspeed + (USB 3.1)) Receptacle Connector 24 Position Surface Mount, Right Angle; Through Hole #commonpartslibrary #connector #usbc #tht

2kOhms 0.5W, 1/2W Through Hole Thumbwheel Potentiometer Top Adjustment

Biosensor Amp/Filter. We are going to use a TL074 to create an instrumentation Amp, Bandpass Filter, and incorporate Driven Right Leg technique. Our goal is to read EEG and EMG signals through connected electrodes.

Through hole footprint. Waveshare Electronics 5.35mm Package None https://www.snapeda.com/parts/RP2040-ZERO/Waveshare+Electronics/view-part/?ref=eda Manufacturer Recommendations NA https://www.snapeda.com/parts/RP2040-ZERO/Waveshare+Electronics/view-part/?ref=snap RP2040-ZERO Low-Cost, High-Performance Pico-Like MCU Board Based On Raspberry Pi Microcontroller RP2040 Waveshare

This is an Energy Meter project leveraging an ATTiny85 microcontroller (U1) to sense current through an ACS712 module (U2). It displays the data in real-time on an OLED display (OLED1) and interacts with three buttons (NEXT, MENU, OK). This compact energy meter is suitable for edge computing and low-power Internet of Things (IoT) applications #project #keypad #arduino #attiny85 #ISP #referenceDesign #edge-computing #edgeComputing #microchip #template #reference-design