This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

18 V battery-powered BLDC blower control board using an Arduino Nano, LM2596 5 V buck module, P-channel MOSFET power cutoff, battery voltage sensing, potentiometer input, buzzer, and red/green status LEDs. High-current 18 V blower path is sized for up to 5 A.

ESP32 DevKitC 38-pin carrier PCB for ultrasonic sensing, servo control, analog microphone and potentiometer inputs, and six LED building channels from a regulated 5V supply.

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

UC3825-based adjustable 10 kHz PWM generator with potentiometer frequency and duty control, plus a 0-15 V MOSFET gate-driver output stage.

Battery-Powered 2-Layer LM358 Analog Replicator PCB with Dual-Gain Edge Potentiometer and Solid 12 V Ground Plane

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

This is a real-time sound generator by thermoacoustic (TA) source using DC biasing technique. In this circuit, a NTE67 n-channel MOSFET is used where the circuit gain is 100. Two resistors in series: 70k (0.1W) + 20k potentiometer are used at gate-to-ground to easily adjust the biasing voltage.

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

This project is a Pulse Width Modulation (PWM) Controller, built around an LM555 timer IC. It controls a load connected to a MOSFET, with adjustments via a potentiometer, and uses capacitors, resistors and diodes for various functions. #PWM #controller #project #Template #projectTemplate