PCB Business Card
Change History from V1: -13.56MHz tuning -larger instruction font -put some stuff on the back I wanted to create a business card that has some functionality and shows off a bit of my portfolio IRL: -NFC to my flux page -here's the awesome [instructables](https://www.instructables.com/PCB-Business-Card-With-NFC/) -Put a bunch of modules on it Find the BoM [here](https://www.digikey.com/short/2db2vnmp)... show more0 Uses
3 Comments
2 Stars
PC Game Controller Any Help?
I don't want to buy an Xbox Controller, so I'm just making one by myself0 Uses
0 Comments
2 Stars
Drone
This PCB is for a quad copter drone. The drone will use a 4S lipo battery as a power supply and each of the motors will use 30Amp ESC's. The microcontroller that handles the RF signals is a Raspberry Pi Pico.... show more0 Uses
211 Comments
2 Stars
SelfCare Plant Final Design
This project is a reference design for an ESP32-WROOM-32E based device. It features USB-C for power and data transfer, onboard voltage regulation, and multiple peripheral connections. It also includes a CH340C for USB to serial conversion #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #referenceDesign #simple-embedded #espressif #template #reference-design... show more0 Uses
173 Comments
2 Stars
USB to Serial Breakout - FT232RL
This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip.... show more0 Uses
39 Comments
2 Stars
7-Segment Controller Rev B
This is a 7-segment controller. It runs on a 3-bit counter so the count is from 0-7. Buttons to toggle reset, pause, increment. Knobs to control speed and lighting configuration. Try the simulation here: https://www.flux.ai/jbreidfjord-dev/7-seg-3-bit-counter... show more0 Uses
38 Comments
2 Stars
STM32 Ethernet board
It is a board based on STM32L4 with a built-in ethernet IC W5500 that allows you to create IoT projects based on the modern ARM Cortex®-M4 core. A connector with SWD interface and USB C for communication are provided for the firmware #IoT #ARM #STM #Ethernet #W5500 #IC #project... show more0 Uses
29 Comments
2 Stars
SparkFun Load Cell Amplifier - HX711
The SparkFun Load Cell Amplifier is a small breakout board for the HX711 IC that allows you to easily read load cells to measure weight. By connecting the amplifier to your microcontroller you will be able to read the changes in the resistance of the load cell, and with some calibration you’ll be able to get very accurate weight measurements. This can be handy for creating your own industrial scale, process control or simple presence detection.... show more0 Uses
28 Comments
2 Stars
Robo Project
The Robo Project is a mobile robotic platform featuring a Particle Argon board, 4 motor-wheels controlled by L293D drivers, and an HC-SR04 ultrasonic sensor for obstacle detection. It's ideal for exploration, remote control, and robotics education. #project #robot #template #L293D #car... show more0 Uses
25 Comments
2 Stars
The Green Dot 2040E5 Board
The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #Seeed #XIOA #LoRa #RP2040 #IoT... show more0 Uses
24 Comments
2 Stars
Arduino ATMEGA2560-16AU Template
Arduino Template based on ATMEGA2560-16AU. This MCU is used in Arduino Mega2560, Arduino Arduino Mega ADK, and some other. This template is a good starting point for your Arduino based project. #Arduino #mega #2560 #ATMEGA2560 #template #project #project-template... show more0 Uses
22 Comments
2 Stars
Gesture Light Switch Relay Reference Design
This project is a Gesture Light Switch Relay Reference Design. It involves an STM32 microcontroller (STMicroelectronics) that interacts with an APDS-9960 sensor (Broadcom) to detect hand gestures. The gesture data is used to control a Toshiba TLP175A relay and an Everlight tri-color LED to switch the light and change colors, respectively. Power is supplied by a Diodes Incorporated's AP2112K-3.3TRG1 regulator. #referenceDesign #edge-computing #edgeComputing #stm #relay #sensors #reference-design... show more0 Uses
21 Comments
2 Stars
Switched-Mode Power Supply (SMPS)
This project is a Switched-Mode Power Supply (SMPS) design. The design incorporates an AC DC Converter (NCP1203D100R2), polarized capacitors, resistors, diodes, connectors, a transistor, a transformer and an integrated circuit. #AC #DC #POWER #NCP1203 #project... show more0 Uses
19 Comments
2 Stars
The Green Dot 2040E5 Board krN5
The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #Seeed #XIOA #LoRa #RP2040 #IoT... show more0 Uses
18 Comments
2 Stars
FM_Transmitter
This is one of the simplest FM transmitters that can be built. It does not require any tuning, and transmit frequency is crystal locked to 90MHz. It eliminates frequency drift common to LC-based FM transmitters. This design is best suited for broadcasting voice or music up to a distance of fifty metres depending on the antenna used.... show more0 Uses
17 Comments
2 Stars
LoRa to WiFi Gateway Reference Design
This project is a LoRa to WiFi Gateway using an ESP32 microcontroller. The design incorporates a LoRa transceiver and a WiFi module to facilitate data transfer between LoRa and WiFi protocols. This gateway can be directly implemented in IoT-based applications where field devices using LoRa need to communicate with WiFi-enabled devices. #referenceDesign #project #ESP32 #LoRa #lora #hub #gateway #ESP32WROOM #RF #WIFI #MCU #referenceDesign #edge-computing #espressif #seeed #seeed-technology #reference-design... show more0 Uses
15 Comments
2 Stars
Aquatimer
AquaTimer is a programmable timer for 12V devices such as lighting, solenoid valves or pumps not only for aquariums. It has three switchable channels for currents up to 2A each and up to 5A in total. Connected lighting can be dimmed if desired and slowly faded in and out to simulate sunrises and sunsets. The internal RTC of the ATtiny is used as a clockwork in conjunction with a 32.768kHz crystal. A backup battery keeps the clock running even if the external power supply is interrupted. Settings are made using three buttons and the OLED display.... show more0 Uses
14 Comments
2 Stars
BQ25895 Reference Design
This project is a reference design based on the BQ25895, a single cell Li-Ion battery charger. It manages the power between an external power source (VIN), a Li-Ion battery (BAT), and a system power rail (SYS). Key features include power-path management, battery thermistor monitoring, and charge status indication. #project #BQ25895 #ReferenceDesign #charger #BatteryManagemen #referenceDesign #bms #texas-instruments #template #reference-design #polygon... show more0 Uses
14 Comments
2 Stars
Picobuck Led Driver (AL8805W5)
(AL8805W5) The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8805 part.... show more0 Uses
13 Comments
2 Stars
Jellybean
The best way to have a friend is to build one. Jellybean is a robot friend whose gonna be right with you. Jellybean has been designed with a number of sensors to be able to interact with the environment and with the owner.... show more0 Uses
12 Comments
2 Stars
Raspberry Pi 3B+ Hat Template
Template for Raspberry Pi 3 Model B+ Shield. Include an official pinout so you will always know Raspberry Pi names, the alternative roles of pins, which one is SDA, or SCL, etc. On PCB you can find the 3D model of the Raspberry Pi itself along with the board outline on the silkscreen. #RaspberryPi #Raspberry #raspberry #raspberrypi #Pi #RPi #Shield #template #project #project-template... show more0 Uses
10 Comments
2 Stars
VL53L4CD Reference Design
This project is a reference design for a VL53L4CD-based sensor circuit. It incorporates the use of a Texas Instruments LP5907MFX-2.8/NOPB to regulate the supply voltage. #referenceDesign #VL53L4CD #project #template #LIDAR #sensor #distance #referenceDesign #industrialsensing #stm #template #reference-design #polygon... show more0 Uses
7 Comments
2 Stars
Interruptor de luz con control gestual
This project is a Gesture Light Switch Relay Reference Design. It involves an STM32 microcontroller (STMicroelectronics) that interacts with an APDS-9960 sensor (Broadcom) to detect hand gestures. The gesture data is used to control a Toshiba TLP175A relay and an Everlight tri-color LED to switch the light and change colors, respectively. Power is supplied by a Diodes Incorporated's AP2112K-3.3TRG1 regulator. #referenceDesign #edge-computing #edgeComputing #stm #relay #sensors #reference-design... show more0 Uses
5 Comments
2 Stars
Simple Charger Modul
This is a simple charger modul that can be connected to a DC generator or solar panel at the input and a battery at the output... show more0 Uses
4 Comments
2 Stars
619 J Stepper
This project is an open source micro-controller board used to drive a stepper motor in closed loop mode. The board is generally used on 3D printer steppers or CNC steppers to prevent losing steps. The project is inspired by Tropical labs: Mechaduino board #motorControllers... show more0 Uses
3 Comments
2 Stars
STM32MP1 Linux Card
This project designs a Linux Single Board Computer using STM32MP157FAC1, featuring DDR memory, a power management IC, USB and SD card interfaces, and essential user controls, aimed at versatile embedded applications.... show more0 Uses
3 Comments
2 Stars
TPS56339 Reference Design
This is a reference design of TPS56339 DC-DC Converter IC with input voltage 4.5-24V and output 5V and 3A #dcdc #ti #power #3A #5V #referenceDesign #powermanagement #texas-instruments #template #reference-design... show more0 Uses
3 Comments
2 Stars
Triple-Axis Accelerometer
The LIS3DH is a very popular low power triple-axis accelerometer. It's low-cost, but has just about every 'extra' you'd want in an accelerometer. This sensor communicates over I2C or SPI (our library code supports both) so you can share it with a bunch of other sensors on the same I2C bus. There's an address selection pin so you can have two accelerometers share an I2C bus... show more0 Uses
1 Comment
2 Stars
ATtiny13 Tiny Neo Tester
An ATtiny13 is more than sufficient to control almost any number of NeoPixels via an IR remote. The NeoController was originally developed as a tester for 800kHz NeoPixel strips. Since there was still so much flash left in the ATtiny13, an IR receiver was integrated so that some parameters can be controlled with an IR remote control. In this way, it is also suitable as a simple and cheap remote-controlled control unit for NeoPixels. Due to its small size (21.6mm x 11.4mm), it can be soldered directly to the LED strip without any problems. The power supply via a USB-C connection enables currents of up to 3A. There is still more than a third of the flash memory left for additional ideas.... show more0 Uses
1 Comment
2 Stars
Capacitive Moisture Sensor (Corrosion-Resistant)
Capacitive Moisture Sensor (Corrosion Resistant) is a soil moisture sensor based on capacitance changes... show more0 Uses
1 Comment
2 Stars
nRF52840 Development Board
The nRF52840 DK is a versatile single board development kit for Bluetooth 5, Bluetooth mesh, Thread, Zigbee, 802.15.4, ANT and 2.4 GHz proprietary applications on the nRF52840 SoC. It also supports development for the nRF52811 SoC.... show more0 Uses
1 Comment
2 Stars
Arduino Multipurpose PCB
This is the multipurpose PCB that works with Arduino Nano, a way that you can run 2 Stepper motors, 2 DC motors, 2 Servo motors at the same time and this is not it you can even connect BT module, rotary encoder, I2C device, potentiometer at same time. This PCB is very much helpful in building any project and no need to worry about messy wire connections.... show more0 Uses
1 Comment
2 Stars
EV5920-5048-V-00A Evaluation Board
This is a recreation of the [EV5920-5048-V-00A](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) from MPS which demonstrates a MP5920 Hot-Swap controller commanding 5 MP5048 e-fuses in parallel. WIP Items: -Routing In flux, this project demonstrates hierarchal design through the use of modules. Additionally, parametric symbols are used extensively to improve schematic cleanliness. Components in the canvas are locked because their positions correspond to the same positions as the original layout. Changelog from Original MPS Design: - Not including GPIO2 or GPIO3 as included in the original board due to NC pin name on the IC. - PC1 and PC2 footprints are 5mm in pitch and 12.5mm in diameter rather than the 16mm diameter in the original layout. This change corresponds with the selected part more accurately. -Renamed Designators to be More Verbose... show more0 Uses
1 Comment
2 Stars
GPS Breakout - ZOE-M8Q (Qwiic)
The SparkFun ZOE-M8Q GPS Breakout is a high accuracy, miniaturized, GPS board that is perfect for applications that don't possess a lot of space. The on-board ZOE-M8Q is a 72-channel GNSS receiver, meaning it can receive signals from the GPS, GLONASS, BeiDou, and Galileo constellations. This increases precision and decreases lock time and thanks to the onboard rechargable battery you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.... show more0 Uses
1 Comment
2 Stars
LoRa Door and Window Sensor Reference Design bbYa
This is a LoRa-based door and window sensor incorporating a microcontroller unit (MCU). It features a reed sensor, LED indicators, a AAA non-rechargeable battery, and a booster IC for constant voltage. The MCU is linked to peripherals through nets, ensuring optimal performance #LoRa #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #seeed #seeed-studio #template #reference-design... show more0 Uses
1 Comment
2 Stars
Wearable biosensor MAX30102 Template
This is a MAX30102 based integrated pulse oximetry and heart-rate monitor biosensor module #wearable #pulse #heartRate #oximeter #MAX30102 #referenceDesign... show more0 Uses
0 Comments
2 Stars
AvocAudio 04_02 Generating Manufacturing Files
AvocAudio is a compact tinyML community board designed for extensive audio data collection for various tinyML applications. It leverages the Raspberry Pi RP2040 and integrates a LoRa-E5 LoRaWAN Transceiver Module for connectivity. Equipped with an SD card slot for local data storage, the board ensures efficient data collection. The board operates on solar power or a lithium-ion battery, ensuring flexible and efficient energy use. #audioDevices #raspberryPi #rp2040 #lorawan #iot #solar... show more0 Uses
0 Comments
2 Stars
ESP32 IMU Template
This project is a small 100mm X 100mm quadcopter controlled by ESP32 and MPU-6050 Template #drone #motorController #ESP32 #controller #motor #helicopter #referenceDesign #project #quadcopter #MPU6050 #template... show more0 Uses
0 Comments
2 Stars
AvocAudio - Fully Placed 23ab 7515
AvocAudio is a compact tinyML community board designed for extensive audio data collection for various tinyML applications. It leverages the Raspberry Pi RP2040 and integrates a LoRa-E5 LoRaWAN Transceiver Module for connectivity. Equipped with an SD card slot for local data storage, the board ensures efficient data collection. The board operates on solar power or a lithium-ion battery, ensuring flexible and efficient energy use. #audioDevices #raspberryPi #rp2040 #lorawan #iot #solar... show more0 Uses
0 Comments
2 Stars
ATTINY841 BMS
DIY BMS using ATTINY841-SSU this hardware has a higher balance current, fuse and TVS diode to help with voltage spikes. Most importantly, an external crystal to the micro controller (attiny841) which means the device is more reliable in low voltage situations... show more0 Uses
0 Comments
2 Stars
Copilot v4 DogFooding - Audio Amplifier
I'm building an audio amplifier. These are the project requirements: - Type of Amplifier: Class D (for energy efficiency). - Input Source: Line-level input from a standard audio source, e.g., mobile phone or PC. - Output Power: 10W per channel (for a stereo setup). - Number of Channels: 2 (stereo output). - Distortion: Total Harmonic Distortion (THD) of less than 0.1% at full power. - Frequency Response: 20Hz to 20kHz. - Power Supply: Operate from a single 12V DC source. - Protection: Over-current and thermal protection for the amplifier IC. - Connectivity: Standard 3.5mm audio jack for input and screw terminals for speaker outputs. - Volume Control: A physical potentiometer for volume control. - Indicator: An LED indicator that shows power ON status. - Size Constraints: PCB size should not exceed 100mm x 100mm. Consider every requirement individually when answering any question... show more0 Uses
0 Comments
2 Stars
Native Bee Hotel V2.5
This bee hotel version is an intermediary version that implements some featuresets. The main feature that we are leaving out is Matter support over Zigbee (for a wider range in the backyard). In this version, we are implmenting: -Legacy WiFi/BT connectivity. -Camera with flash capability -Solar Charging -Energy Storage -Humidity and Temp Sensor... show more0 Uses
0 Comments
2 Stars
NPN-TRANS-001
The Ariel AI chip prototype is an advanced electronic component designed to enhance the capabilities of Flux AI systems through a sophisticated arrangement of transistors, resistors, capacitors, and a cutting-edge CPU. Key components include two NPN transistors (part numbers NPN-TRANS-001 and NPN-TRANS-002), which are essential for signal amplification, alongside precision resistors (RES-1K and RES-1K-002) each with a resistance of 1kΩ, and a capacitor (CAP-10UF) with a capacitance of 10μF, crucial for filtering and stabilizing the voltage supply. At the heart of the design is a revolutionary CPU (part number CPU-RT-4C-2G) featuring a quad-core setup with a clock speed of 2GHz, based on a radical transistor architecture, designed to deliver unparalleled computational performance for AI tasks. This component set is powered by a 5V DC power supply (DCPS-5V), ensuring a stable and efficient operation. The Ariel AI chip is engineered for high-speed, reliable performance in demanding AI applications, representing a significant advancement in electronic component design for artificial intelligence systems.... show more0 Uses
0 Comments
2 Stars
Arduino-UNO-R3
The Arduino Uno R3 is a microcontroller board based on a removable ATmega328P 20 digital input/output pins AVR MCU 8-Bit 5V USB 16MHz #Module #Arduino... show more0 Uses
0 Comments
2 Stars
Raspberry Pi Pico 2 Shield Template
This is the project template for the Raspberry Pi Pico 2, the latest addition and update to Pi Pico line up. Raspberry pi pico 2 is equipped with the RP2350, a cutting-edge, high-performance microcontroller designed with enhanced security and versatility in mind. Every element of its design has been upgraded, from the advanced CPU cores to the innovative PIO (Programmable I/O) interfacing subsystem. The Raspberry Pi Foundation has integrated a robust security architecture centered around Arm TrustZone for Cortex-M, ensuring data protection and integrity. Additionally, new low-power states and expanded package options broaden the range of applications, making the Pico 2 an ideal choice for diverse, power-sensitive projects. To learn more about what's the key differences between the original Pi Pico and the new Pi Pico 2, read our blog https://www.flux.ai/p/blog/whats-new-in-the-raspberry-pi-pico-2-a-showdown-with-the-original-raspberry-pi-pico #project-template #template #raspberry #pi #pico2 #newpico... show more0 Uses
0 Comments
2 Stars
4017 Chaser
Running LED circuit that utilizes a 555 clock output and a decade counter. It runs when the push-button is held down and then slowly stops once it is released.... show more0 Uses
0 Comments
2 Stars
ADP1618 Reference Design
This is a reference design of step-up converter based on ADP1618 with 5V input and 12V output #dcdc #5V #12V #power#referenceDesign #powermanagement #analogdevices #template... show more0 Uses
0 Comments
2 Stars
Electronic smoke screen
This design is three parts, one a bandpass filter to allow only a certain frequency to come through the device, and the other two to filter and jam out different frequencies that would be coming near the device. The bandpass is set at 450MHz as is the common frequency for phones, the top jammer is set up for blocking out typical radio frequencies while the bottom is set to block frequencies above that of a phone signal. Vin=20 volts... show more0 Uses
0 Comments
2 Stars
Aaduino
The AAduino is an wireless Arduino clone the size of an AA battery with Keystone battery terminals rotated 180° to act as positive and negative terminals. It is meant to go inside a 3xAA battery holder creating a very small wireless node. Powered by an ATMega328p, it is fitted with an RFM69CW companion, two DS18B20 temperature sensors and an indicator LED... show more0 Uses
0 Comments
2 Stars
Seeed Studio XIAO ESP32C6
Seeed Studio XIAO ESP32C6 is powered by the highly-integrated ESP32-C6 SoC, built on two 32-bit RISC-V processors, with a high-performance (HP) processor with running up to 160 MHz, and a low-power (LP) 32-bit RISC-V processor, which can be clocked up to 20 MHz. There are 512KB SRAM and 4 MB Flash on the chip, allowing for more programming space, and binging more possibilities to the IoT control scenarios.... show more0 Uses
0 Comments
2 Stars
