An ATtiny13 is more than sufficient to control almost any number of NeoPixels via an IR remote. The NeoController was originally developed as a tester for 800kHz NeoPixel strips. Since there was still so much flash left in the ATtiny13, an IR receiver was integrated so that some parameters can be controlled with an IR remote control. In this way, it is also suitable as a simple and cheap remote-controlled control unit for NeoPixels. Due to its small size (21.6mm x 11.4mm), it can be soldered directly to the LED strip without any problems. The power supply via a USB-C connection enables currents of up to 3A. There is still more than a third of the flash memory left for additional ideas.

BLE remote control board. Based on SoC ESP32-C3-MINI-1 that allows you to program it as HID volume multichannel control, you can switch channels with the user button, or use it as arrow keys.

I'm building an audio amplifier. These are the project requirements: - Type of Amplifier: Class D (for energy efficiency). - Input Source: Line-level input from a standard audio source, e.g., mobile phone or PC. - Output Power: 10W per channel (for a stereo setup). - Number of Channels: 2 (stereo output). - Distortion: Total Harmonic Distortion (THD) of less than 0.1% at full power. - Frequency Response: 20Hz to 20kHz. - Power Supply: Operate from a single 12V DC source. - Protection: Over-current and thermal protection for the amplifier IC. - Connectivity: Standard 3.5mm audio jack for input and screw terminals for speaker outputs. - Volume Control: A physical potentiometer for volume control. - Indicator: An LED indicator that shows power ON status. - Size Constraints: PCB size should not exceed 100mm x 100mm. Consider every requirement individually when answering any question

10A MPPT Solar Charge Controller with dual USB ports using Low-power 32bit ARMCortex-M0+ MCU (STM32L072). Expandable via Olimex Universal Extension Connector (UEXT) featuring I2C

Controller for vending machine. Use stm32f407, pressure sensor HX711, FRAM, TFT display connectivity.

I don't want to buy an Xbox Controller, so I'm just making one by myself

This device will be connected to computer through type-C and recognize as MIDI device. User can change two effects(A and B) from lists, effect speed(Tempo) and volume.

Welcome to your new project. Imagine what you can build here.

Weather Station controlled by STM32F031F6P6 MCU. 2x humidity and temperature sensors. USB powered

This is a recreation of the [EV5920-5048-V-00A](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) from MPS which demonstrates a MP5920 Hot-Swap controller commanding 5 MP5048 e-fuses in parallel. WIP Items: -Routing In flux, this project demonstrates hierarchal design through the use of modules. Additionally, parametric symbols are used extensively to improve schematic cleanliness. Components in the canvas are locked because their positions correspond to the same positions as the original layout. Changelog from Original MPS Design: - Not including GPIO2 or GPIO3 as included in the original board due to NC pin name on the IC. - PC1 and PC2 footprints are 5mm in pitch and 12.5mm in diameter rather than the 16mm diameter in the original layout. This change corresponds with the selected part more accurately. -Renamed Designators to be More Verbose

This project is a small 100mm X 100mm quadcopter controlled by ESP32 and MPU-6050 Template #drone #motorController #ESP32 #controller #motor #helicopter #referenceDesign #project #quadcopter #MPU6050 #template

A simple 3DO in-game reset mod. MCU sniffs controller data and fires a reset signal to the console when L+R+X+P buttons are pressed.

DIY BMS using ATTINY841-SSU this hardware has a higher balance current, fuse and TVS diode to help with voltage spikes. Most importantly, an external crystal to the micro controller (attiny841) which means the device is more reliable in low voltage situations

This is a BLE remote control Reference Design. It features a Microchip RN4871U BLE module for communication, various push buttons (Up, Down, Left, Right, OK) for control input, and a piezoelectric buzzer for audio feedback. Power is supplied by a battery and it is regulated to 3.3V for the BLE module. #BLE #IoT #referenceDesign #simple-embedded #microchip #template #reference-design

This is a BLE remote control Reference Design. It features a Microchip RN4871U BLE module for communication, various push buttons (Up, Down, Left, Right, OK) for control input, and a piezoelectric buzzer for audio feedback. Power is supplied by a battery and it is regulated to 3.3V for the BLE module. #BLE #IoT #referenceDesign #simple-embedded #microchip #template #reference-design

Designing a control board for a smart vending machine. Board will house an ESP32, AC and DC power supply, terminal port for stepper motor, MG990 servo motor, SIM7200 GSM module, 2004 LCD screen.

Control de acceso

This is a climate control system reference design with a STM32WB5 microcontroller, power manager IC, USB Type-C, JST connectors, and an LCD driver. #referenceDesign #edge-computing #edgeComputing #stm #template #iot #control #BLE #reference-design

This is a smart blind control system reference design designed to automate the operation of window blinds. It utilizes an ESP32 microcontroller for managing control signals and an A4988 stepper motor driver to control blinds' movement. It also includes USB interfacing and LED feedback. #referenceDesign #edge-computing #edgeComputing #espressif #template #blind #DC #motor #servo #esp32 #reference-design

Control de un LCD1602 (HD44780) en modo paralelo de 8 bits con Arduino Uno R3, ajuste de contraste por potenciómetro, retroiluminación con resistencia en serie y desacoplo con condensadores de 100 nF y 10 µF

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.