This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #attiny2313 #TPS613222A #ISP #buzzer #reusable #module #simple-embedded #microchip #arduino #sublayout

Through hole straight pin header, 1x04, 4 pin, 4-pin, horizontal, angled, 2.54mm pitch, 6mm pin lenght single row

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #arduino #attiny2313 #TPS613222A #ISP #buzzer #referenceDesign #simple-embedded #microchip #template #reference-design

An I2C extension shield with 6 shielded ethernet ports and a TCA9548 breakout board. This board is for the target side, any microcontroller with a standard Arduino header can use it. With proper target side hardware and an SSTP ethernet cable, the board provides robust i2c communication over 10ft(could be longer, haven't tested it yet) with a bitrate of 400kHz under a noisy environment( near motors, power cables, switches, etc). The shield board provides power to the target side and can power the i2c device. The board also supports drdy trigger, which is available on many i2c sensors. The TCA9548 breakout board is for a scenario in which all of your i2c devices have the same address. #Arduino #Uno #Shield #Template #project-template #project

Important Note: You must connect your own SPI/ICSP programming header if you want to burn the Arduino bootloader to the MCU. SMD Manufacturing: Need a hotplate and solderpaste Good to haves: - Oscillator Decoupling Caps Expose UART via connector Programming Button Onboard LED Reset Button You don't have to populate everything! Only these are mandatory: Reset Button Find the reference schematic here: https://www.arduino.cc/en/uploads/Main/ArduinoNano30Schematic.pdf

Connector Header Through Hole 2 position 0.079" (2.00mm) 01x02 JST B2B PH K

DeskNeuron V0.1 — USB-C ESP32-S3 6-key macro pad with dual EC11 encoders and SPI TFT header.

Raspberry Pi Zero HAT-style PCB with bottom 40-pin GPIO header and top-side connectors for MLX90640 thermal camera, SCD41, PIR, IMU, OLED, and thermal sensor terminals.

Battery-powered infrared/PIR sensor board with USB-C charging, single-cell LiPo battery input, 3.3 V regulation, sensor output header, and status indicators.

Arduino Mega 2560 sensor/actuator interface shield for a firefighting differential robot with labeled connectors, onboard IR receiver, buzzer, MPU6050 header, battery VIN protection, battery sensing, LED outputs, and fan MOSFET control.

Multi-subsystem ESP32-S3 coffee maker/alarm controller board for a Coffee Waker appliance. The design uses an ESP32-S3-WROOM-1-N8R8 module as the main Wi-Fi/Bluetooth MCU, with USB-C 2.0 device connectivity through a USB4105-GF-A connector, 5.1 kΩ CC pull-downs, and USBLC6-2SC6 ESD protection on the USB D+/D− pair. Power architecture includes a 12 V input on a JST VH B4P connector, a TPS62932 buck regulator generating the 5 V rail, a TLV1117LV33 3.3 V LDO for MCU/logic power, and TPS22919 load switches for controlled 3.3 V/5 V peripheral rails. Functional blocks include an NAU7802 load-cell ADC on I2C with two differential load-cell channels, a MAX98357A I2S audio amplifier/DAC with speaker/output filtering, a microSD socket on SDIO, I2C/test headers, UART/programming header, and auxiliary JST VH connectors for wake-light or external loads. The high-voltage section includes 120 VAC input/output screw terminals, a 5 V SPST-NO relay rated 15 A / 240 VAC max, a 1 A fuse, MOV surge suppression, diode snubber, and a dedicated heater output terminal.

USB-powered ESP32-WROOM-32 industrial vibration and temperature monitoring sensor node with ADXL345 SPI accelerometer, DS18B20 1-Wire temperature sensor, SSD1306 I2C OLED, LEDs, buzzer, relay header, and 3.3V AMS1117 power supply.

JST XH Connector Header Through Hole 6 position 0.098" (2.50mm) #commonpartslibrary #connector #header #tht #JST-XH

Low-voltage logic-only CERILUME Phase 1 LED controller using an Arduino Nano ESP32 plug-in module, 5V logic level shifting for WS2812/SK6812 data, microphone input header, and labeled test pads. LED power distribution and high-current switching are intentionally out of scope.

Interface board connecting a 64-pin TE CMC connector 2209129-1 to a 64-pin TE ribbon header 1-5102154-2 with straight-through pin mapping from pin 1 to pin 64.

Cyberdeck power distribution hub using a TP4056 Type-C Li-ion charger module, MT3608 boost converter module, switched output rail, voltmeter, servo, Arduino VIN, button signal header, and battery terminal on a 50 mm × 70 mm PCB.

USB-C powered ESP32 WiFi water flow meter for an external ultrasonic sensor on 3/4 inch PVC pipe, with protected 5V input, 3.3V regulation, programming header, reset/boot support, and status LEDs.

Scary Aquamarine Scramble Suit — Raspberry Pi LiDAR Scanner HAT with TFmini-Plus UART, TMC2209 stepper drive, MPU-6050 IMU, USB-C 5V input, 12V motor input, debug header, LEDs, and test points for indoor 360° obstacle mapping.

USB-C powered ESP32 WiFi water flow meter schematic with protected 5V input, 3.3V LDO, 12V boost supply for an external RS485 ultrasonic sensor, UART programming header, boot/reset network, and three status LEDs for power, WiFi, and flow activity.

Industrial ESP32-C3 controller board with isolated RS-485, protected 12V-24V input, opto-isolated digital inputs, sensor interfaces, and production debug header.

2-layer SELV ESP8266 smart relay logic board using an ESP-12F module, MCP1700-3302E 5V-to-3.3V LDO, exact 2x7 relay/control connector pinout, 4-pin UART programming header, GPIO0 flash test point, active-low GPIO2 status LED, power and GPIO test points, 55x45 mm board outline, top-side assembly, bottom solid ground pour, ESP-12F antenna keepout, 4 M3 mounting holes, and silkscreen connector labels for production use.

Conservative first-revision TIMI prototype built around ESP32-S3-WROOM-1-N16R8 with USB-C 5V input, native USB, 3.3V regulation, onboard MAX98357A audio out, external INMP441 header, status LEDs, buttons, UART debug header, required test points, and 4-layer antenna-conscious PCB constraints.

WT32-ETH01 carrier refactored for a single 2x10 WT32 header, 12V input terminal, 6-pin Wiegand terminal, and a 12V-to-5V buck stage with level-shifted D0/D1 plus transistor-driven LED and BUZZER outputs, prepared for a simple 2-layer layout.

PIC16F877A-based load-cell measurement system using an HX711 24-bit ADC, 4 MHz crystal clock, load-cell connector, ICSP programming header, regulated 5V input, and low-noise PCB layout for internship deliverables.

Experimental 21V/5S Li-ion DeWalt battery charger with 21V DC input, relay-switched charge path, tap monitoring, ESP32-WROOM external controller interface, test header, and 2-layer prototype PCB intent.