Through-hole NE555 astable circuit that blinks a red LED about once per second from a switched 9V battery.

Through-hole 9V NE555 astable timer circuit that blinks a red LED about once per second using a battery and on/off switch.

Hand-solderable 9V battery powered 555 timer circuit that blinks a red LED once per second through an on/off switch.

Hand-solderable 9V 555 timer circuit that blinks a red LED once per second through an on/off switch.

Simple hand-solderable 9V battery LED blinker using a NE555 astable oscillator, on/off switch, battery snap connector, supply decoupling, and a red status LED blinking at approximately 1 Hz.

Simple 9V battery-powered NE555 astable LED blinker with on/off switch, red indicator LED, and hand-solder-friendly through-hole components.

9V battery-powered NE555 astable LED blinker (~1 Hz) with on/off switch; through-hole hand-solderable parts.

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

Motion activated light for 9v batteries

Circuito de control de sentido de giro de un motor de DC.

Welcome to your new project. Imagine what you can build here.

Use this template if you're planning to get your 1 to 2-layer board manufactured in JLCPCB. It has the via min/max and trace width constraints already baked as global rules. #project-template #template #manufacturer-design-rules

Hand-solderable 9 V battery-powered 555 timer circuit that blinks a red LED approximately once per second through an on/off switch.

Hand-solderable NE555 astable LED blinker powered from a 9 V battery with an on/off switch and approximately 1 Hz blink rate.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Software: Linux Power Requirements: LiPo battery powered Compliance: RoHS Connectivity: USB, WiFi, Bluetooth, Ethernet Human Interface: Joystick, Display Operating Voltage: 3.3V, 5V, 9V Operating Temp: -40 to +85C Reliability: 10,000hrs MTBF Target Cost: $100

Phantom 24V 9V Input

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply (including LED), a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. #template

Mini Paper USV PCB Upgrade v1.0 schematic twin using an ELEGOO MEGA 2560, L293D H-bridge, HC-SR04 ultrasonic sensor, SG90 servo header, LED indicators, buzzer, and dual 9V parallel battery input.

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template