Jerky Robot V3 100 mm × 152 mm 2-layer control board with ESP32-S3 and Arduino Nano sockets, screw-terminal I/O, BSS138 UART level shifting, PC817 sensor isolation, optional HX711 interface, status LEDs, test points, top-side component placement, and bottom GND fill for JLCPCB fabrication.

Compact 2-layer ESP32-S3-MINI-1 piezo TX/RX board for a shared 3 MHz transducer node. Includes USB 5 V input, TP4056 single-cell LiPo charging, TLV75533 3.3 V regulation, ferrite-bead isolated 3V3_ANALOG rail, ~12 V pulsed TX boost rail, low-gate-charge NMOS transmit driver, clamp-protected RX input, 2-stage OPA836 analog receive chain, envelope detector, ADC interface, TMP117 I2C temperature sensor, and status LEDs. Layout intent: piezo centered, RX chain within 10 mm of PIEZO_NODE, boost section remote from RX, digital and analog partitioning, and AGND/DGND star connection near RX front end.

This project is a Wearable Accelerometer based on BHI160B sensor with an I2C interface. The design includes decoupling capacitors and pull-up resistors for signal integrity. It's powered by a 3.3V supply. #wearables #referenceDesign #project #sensor #accelerometer #BHI160B #referenceDesign #imu #stm #template #reference-design

This project is a Wearable Accelerometer based on BHI160B sensor with an I2C interface. The design includes decoupling capacitors and pull-up resistors for signal integrity. It's powered by a 3.3V supply. #wearables #referenceDesign #project #sensor #accelerometer #BHI160B #referenceDesign #imu #stm #template #reference-design

INA3221 current and voltage monitor interface for an HC-SR04 ultrasonic sensor, with 5V sensor power routed through a shunt and I2C output to a host MCU.

A simple Arduino weather shield which allows an Arduino Uno R3 to interface with: ● Barometric pressure sensor ● Phototransistor ● Humidity Sensor ● Temperature Sensor #Arduino #Uno #Shield #Template #project-template #project

This project is a Smart Thermostat design using an ESP32 module for WiFi connectivity and a BME680 sensor for environmental monitoring. The user interface includes an E-ink display and an encoder for settings adjustment. Power is managed through a USB-C connector with a 3.3V regulator. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #thermostat #referenceDesign #edge-computing #edgeComputing #espressif #template #reference-design

This project is a Smart Thermostat design using an ESP32 module for WiFi connectivity and a BME680 sensor for environmental monitoring. The user interface includes an E-ink display and an encoder for settings adjustment. Power is managed through a USB-C connector with a 3.3V regulator. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #thermostat #referenceDesign #edge-computing #edgeComputing #espressif #template #reference-design

This project is a Smart Thermostat design using an ESP32 module for WiFi connectivity and a BME680 sensor for environmental monitoring. The user interface includes an E-ink display and an encoder for settings adjustment. Power is managed through a USB-C connector with a 3.3V regulator. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #thermostat #referenceDesign #edge-computing #edgeComputing #espressif #template #reference-design

This project is a Smart Thermostat design using an ESP32 module for WiFi connectivity and a BME680 sensor for environmental monitoring. The user interface includes an E-ink display and an encoder for settings adjustment. Power is managed through a USB-C connector with a 3.3V regulator. #referenceDesign #project #ESP32 #ESP32WROOM #RF #WIFI #MCU #thermostat #referenceDesign #edge-computing #edgeComputing #espressif #template #reference-design

Raspberry Pi Zero 2W with 5V MQ Gas Sensor and ADS1115 I²C ADC: Breadboard Interface Design

Interface for Wemos D1 mini to sct-013 current sensor via a 3.5mm jack

USB-C powered ESP32 WiFi water flow meter interface for a 3/4 inch PVC ultrasonic RS485 flow sensor, including 12V sensor power, 3.3V logic power, protection, status LEDs, and programming/reset support.

Active USB-C Wi-Fi & BLE Environmental Sensor Node with Cloud Connectivity and Integrated Six-Button User Interface

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

Battery-powered ESP32-S3 LoRa ePaper sensor board with SHT41 environmental sensing, LiPo charging/fuel gauge, 5V input detection, and a 4.2 inch 300x400 b&w ePaper interface in an 85 x 60 mm low-profile PCB.

ESP32-based sensor camera system with HC-SR04, NEO-6M GPS, ESP32-CAM, optional FT232RL programming interface, 5V input, and regulated 3.3V logic rail.

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

This project is a BLE door and window sensor design that uses a U-blox BMD-330-A-R for BLE communication, a reed switch as a sensor, a multi-color LED for status display, and is powered by VBAT. There's also a programming interface and reset switch included. #WiFi #BLE #MCU #ReferenceDesign #project #referenceDesign #simple-embedded #ublox #template #reference-design

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design

This project is a design for a UV sensor circuit based on the Lite-On LTR-390UV-01. Key components include a voltage regulator (AP2112K-3.3TRG1), level-shifting N-channel MOSFETs (BSS138), resistors, and capacitors. The circuit interface includes I2C communication and power connections, facilitated through JST connectors. #referenceDesign #industrialsensing #liteon #template #reference-design

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design