Minimal components Sub Layout for STM32F030 Value Line ARM Cortex-M0 MCU with crystal

Minimal components Sub Layout for STM32F030 Value Line ARM Cortex-M0 MCU with crystal

Minimal components Sub Layout for STM32F030 Value Line ARM Cortex-M0 MCU with crystal

Minimal components Sub Layout for STM32F030 Value Line ARM Cortex-M0 MCU with crystal

DIY BMS using ATTINY841-SSU this hardware has a higher balance current, fuse and TVS diode to help with voltage spikes. Most importantly, an external crystal to the micro controller (attiny841) which means the device is more reliable in low voltage situations

Minimal components Sub Layout for STM32F030 Value Line ARM Cortex-M0 MCU with crystal

Compact USB-C RP2040 development board with external QSPI flash, crystal, protected USB 2.0, LEDs, BOOTSEL, and test-pad debug access.

Compact surface-mount production variant of the fixed-function, crystal-referenced low-power burst timer. Electrically equivalent to the through-hole version where practical, with selectable interval, duration, carrier frequency, AUTO/TEST mode, ENABLE output, and gated OSC_OUT; no MCU, firmware, PLL, VCO, or programmable logic.

Prototype breadboard-friendly breakout board for the Realtek RTL8761BTV-CG Bluetooth 5 UART HCI controller, with 0.1 inch headers, 3.3 V power input, support passives, 40 MHz crystal, and RF antenna matching provisions.

Professional 4-layer STM32H743ZIT6 learning/development board with USB-C power, USB FS, SWD, crystals, SPI flash, ESP-12F Wi-Fi, full GPIO breakout, and expansion headers.

ATmega328P microcontroller schematic with recommended power decoupling, reset circuit, 16 MHz crystal clock, and ISP/UART breakout support.

Resonate Pendant golden reference design. Board is a 39 mm x 63 mm portrait rectangle with 5 mm corner radii, 2-layer FR4, 0.8 mm thickness, 1 oz copper on both layers, matte black top solder mask, no bottom solder mask, ENEPIG finish, and no silkscreen on either side. Allowed components only: U1 STM32L052C8T6, U2 CH340E, U3 BQ24210DQCT, C1 10uF, C2 4.7uF, C3-C7 100nF, R1 24k, R2 1k, R3 10k, D1 green 0402 LED, MAG1-MAG4 magnetic pads, J1 solar solder pads, J2 battery solder pads, TP1-TP4 test pads. Required top artwork: golden-ratio grid lines and gold circles on F.Cu with mask openings, decorative only, 0.8-1.0 mm width, at least 0.5 mm from active traces. Required bottom artwork: exposed ENEPIG bottom copper split into FREQ_OUT 61.8 percent and GND 38.2 percent with an exact 0.20 mm S-curve isolation gap, no vias through bottom except one PA4-to-FREQ_OUT via at the extreme edge. Functional requirements: MAG1 and J1 VIN feed U3 IN, U3 OUT feeds J2 battery pad and system VBAT, MAG2 to U2 UD+, MAG3 to U2 UD-, MAG4 to common ground, U2 TX to U1 PA10, U2 RX to U1 PA9, U1 PA4 to bottom FREQ_OUT, U1 PA5 to R2 then D1 to GND, U3 ISET to R1 to GND, U3 TS to R3 to GND, decoupling exactly as specified. Prohibited items: external crystal, JST connectors, wireless module, antenna, separate regulator IC, ESD protection IC, USB-C connector, through-hole parts, bottom solder mask, silkscreen, more than three ICs, or any unapproved substitutions.

PIC16F877A-based load-cell measurement system using an HX711 24-bit ADC, 4 MHz crystal clock, load-cell connector, ICSP programming header, regulated 5V input, and low-noise PCB layout for internship deliverables.

Datasheet-driven MFRC522 RFID reader PCB intended to replicate RC522 module behavior at 13.56 MHz with a 3.3 V nominal supply, 2.5 V to 3.3 V operating range, and RC522-style 8-pin host header compatibility. The MFRC522 datasheet is the authoritative source for pin usage, power rail relationships, oscillator requirements, reset/IRQ handling, and antenna interface topology. AVDD, DVDD, and TVDD must be tied to the same 3.3 V rail; PVDD must be equal to or lower than DVDD; unused MFIN must be tied to SVDD or PVSS; SVDD must be tied to a valid supply if not used independently. The design must use a 27.12 MHz crystal meeting CL 10 pF and ESR <= 100 ohms, local 100 nF decoupling on each MFRC522 supply grouping plus bulk capacitance, and an RF front-end based on the MFRC522 application diagram and reference reader matching/tuning network. PCB priorities are short crystal and RF connections, compact placement of decoupling capacitors at supply pins, solid ground reference, and protected antenna region with minimal digital routing through the RF area.

ATmega328P 5V External-Powered Clock and Reset Core (16 MHz Crystal, Screw-Terminal Input)

Template for working with ATMEGA328PB (using 16MHz crystal)

Template for working with ATMEGA328PB (using 16MHz crystal)

Template for working with ATMEGA328PB (using 16MHz crystal)

This project is a template for projects involving RP2040. It consists of the chip, the decoupling capacitors, the crystal oscillator and the flash memory. #raspberryPi #rp2040 #template

The Micro is a microcontroller board based on the ATmega32U4 (datasheet), developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard. The Micro board is similar to the Arduino Leonardo in that the ATmega32U4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Micro to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port.

8MHz 20pF ±20ppm HC-49S-SMD Crystals ROHS

Template for working with ATMEGA328PB (using 16MHz crystal)

DIY BMS using ATTINY841-SSU this hardware has a higher balance current, fuse and TVS diode to help with voltage spikes. Most importantly, an external crystal to the micro controller (attiny841) which means the device is more reliable in low voltage situations

DIY BMS using ATTINY841-SSU this hardware has a higher balance current, fuse and TVS diode to help with voltage spikes. Most importantly, an external crystal to the micro controller (attiny841) which means the device is more reliable in low voltage situations

Discover the benefits of the HC32L110 microcontroller with our compact and versatile breakout board, designed to streamline development and testing for various applications. This user-friendly solution offers essential components like decoupling capacitors, a 32MHz crystal oscillator, and accessible power supply connections. The breakout board also features 0.1" pitch connectors, allowing for easy integration of I/O pins into any project. Unlock the full potential of the HC32L110B6YA-CSP16 microcontroller for rapid prototyping and smooth deployment with our ingeniously designed breakout board.