NodeMCU V3 ESP8266 ESP-12E is WiFi development board that helps you to prototype your IoT product with few Lua script lines, or through Arduino IDE. The board is based on ESP8266 ESP-12E variant, unlike other ESP-12E, you won’t need to buy a separate breakout board, usb to serial adapter, or even solder it to a PCB to get started, you will only need a usb cable (Micro USB).

NodeMCU V3 ESP8266 ESP-12E is WiFi development board that helps you to prototype your IoT product with few Lua script lines, or through Arduino IDE. The board is based on ESP8266 ESP-12E variant, unlike other ESP-12E, you won’t need to buy a separate breakout board, usb to serial adapter, or even solder it to a PCB to get started, you will only need a usb cable (Micro USB).

NodeMCU V3 ESP8266 ESP-12E is WiFi development board that helps you to prototype your IoT product with few Lua script lines, or through Arduino IDE. The board is based on ESP8266 ESP-12E variant, unlike other ESP-12E, you won’t need to buy a separate breakout board, usb to serial adapter, or even solder it to a PCB to get started, you will only need a usb cable (Micro USB).

D1 Mini breakout for added module boards focused on plant / planter care. OSH Park constraints.

Guitar pedal starter template based on project by Mark Wu. Includes schematic and PCB layout for basic DIY pedal hardware. This includes two 1/4" jacks (one for input and one for output), a 9V power supply, a 3PDT true bypass wiring setup, and an example potentiometer that can be copy/pasted throughout the circuit. size is a good default size for a 125B enclosure. The headers are meant to be unpopulated so that wires can be soldered to the pads. PCB design rules imported from the JLCPCB 2-layer stackup template. Meant to be used with the 3PDT Breakout Board on my profile. #template

NodeMCU V3 ESP8266 ESP-12E is WiFi development board that helps you to prototype your IoT product with few Lua script lines, or through Arduino IDE. The board is based on ESP8266 ESP-12E variant, unlike other ESP-12E, you won’t need to buy a separate breakout board, usb to serial adapter, or even solder it to a PCB to get started, you will only need a usb cable (Micro USB).

Breakout board for the LP5012. Not including pull up resistors.

An I2C extension board with LTC4311 bus accelerator and shielded ethernet port. This board is for the target side. With proper controller side hardware and an SSTP ethernet cable, the board provides robust i2c communication over 10ft(could be longer, haven't tested it yet) with a bitrate of 400kHz under a noisy environment( near motors, power cables, switches, etc). The breakout board receives power from the controller side and can power i2c device. The board also supports drdy trigger, which is available on many i2c sensors. #project #I2C #shielded #robust #ltc4311 #long-distance

This is a compact breakout board with battery connectors, compatible with various Seeed boards such as the XIAO ESP32-C6, designed for compact prototyping and integration.

Breakout board for HC32L110 MCU in 16-CSP package

ESP32 breakout board with DHT11 sensor and

NXP Precision 9DoF breakout combines two of the best motion sensors we've tested here at Adafruit: The FXOS8700 3-Axis accelerometer and magnetometer, and the FXAS21002 3-axis gyroscope

Breakout board for HC32L110 MCU in 16-CSP package

Breakout board for HC32L110 MCU in 16-CSP package

Breakout board for HC32L110 MCU in 16-CSP package

Breakout board for HC32L110 MCU in 16-CSP package

This is an isolated CAN bus breakout board that uses the Texas Instruments chipset ISO1050 along with an isolated DC/DC converter.

Compact MAX86141 reflective PPG sensor breakout with 3.3 V host power, SPI, green/red/IR emitter, and external photodiode.

Small breadboard-friendly breakout/carrier PCB for the Moddo pinch SAMD11 dev board, converting its 16-pin 1.27 mm header to 2.54 mm through-hole breakout pins. Mechanical dimensions are marked verify-against-hardware until Moddo publishes official drawings.

Prototype breadboard-friendly breakout board for the Realtek RTL8761BTV-CG Bluetooth 5 UART HCI controller, with 0.1 inch headers, 3.3 V power input, support passives, 40 MHz crystal, and RF antenna matching provisions.

Arduino Nano-style ATmega328P breakout with CH340G USB-to-serial interface, USB power input, reset/clock support, and programming headers.

Motorized Fader Passive Breakout (RSA0N11M9A0J)

This is a compact breakout board with battery connectors, compatible with various Seeed boards such as the XIAO nRF52840, ESP32-S3, and ESP32-C3, designed for compact prototyping and integration.

Looking for a low-cost way to send and receive data messages via satellite? This is it! With a clear view of the sky, the Satellite Transceiver Breakout - Swarm M138 allows you to send and receive short messages. It works anywhere in the world, including the polar regions, far beyond the reach of WiFi and Cellular networks. It is perfect for a variety of low-bandwidth use cases: from connecting people and tracking vehicles, ships, or packages to relaying sensor data for agriculture, energy, and industrial IoT applications. The built-in GNSS receiver makes it perfect for many tracking applications.

Discover the benefits of the HC32L110 microcontroller with our compact and versatile breakout board, designed to streamline development and testing for various applications. This user-friendly solution offers essential components like decoupling capacitors, a 32MHz crystal oscillator, and accessible power supply connections. The breakout board also features 0.1" pitch connectors, allowing for easy integration of I/O pins into any project. Unlock the full potential of the HC32L110B6YA-CSP16 microcontroller for rapid prototyping and smooth deployment with our ingeniously designed breakout board.