Chat

Welcome to Flux

Treat Flux like your intern. Tell it what you'd like to build and it'll get to work. You can also ask it questions, brainstorm ideas, and teach it your preferences. Learn More

Explain project

Write a project description

Find schematic issues

Create a test plan

Simulate a circuit

Prepare for Manufacturing

Component Selection Workflow

New Subsystem Wizard

Ready.

can you give me advise which transitor is best for switching 5V usb voltage in o...

pmamatis

@copilot can you give me advise which transitor is best for switching 5V usb voltage in order to drive waterpumps with 300mA

copilot

For switching a 5V USB voltage to drive a waterpump with a current requirement of 300mA, I recommend using a N-channel MOSFET due to its high efficiency, lower voltage drop, and simplicity for such an application. A good choice would be to select a logic-level MOSFET, as it will be fully turned on (saturated) at the lower gate voltages provided by microcontroller GPIO pins, such as those on the ESP32.

Here are two commonly recommended logic-level N-channel MOSFETs for your requirements:

IRLZ34N
- Threshold Voltage (Vgs(th)): Typically around 1V to 2V, ensuring it fully turns on at the 3.3V logic level available from the ESP32.
- Continuous Drain Current (Id): Greater than 300mA, specifically around 30A, which is way more than what's required for your application but provides a good safety margin.
- Rds(on): Very low on-resistance, ensuring minimal power loss across the MOSFET when on.
2N7000
- Threshold Voltage (Vgs(th)): Approximately 2.1V, making it suitable for logic-level operation as well.
- Continuous Drain Current (Id): Up to 200mA, which is slightly lower than your requirement. For a safety margin, it's often recommended to use components rated for higher than the actual anticipated current. Therefore, consider this option if your water pump can operate slightly below 300mA or if you can find a variant or similar MOSFET with a higher current rating.
- Rds(on): Slightly higher on-resistance compared to power MOSFETs but still acceptable for low current devices.

Given that the 2N7000 is on the edge of your current requirements, I'd lean towards recommending the IRLZ34N for its higher current capacity, low Rds(on), and overall headroom for your application. This will ensure reliable operation and reduce the chances of overheating and failure.

When interfacing this MOSFET with your ESP32, ensure you include a pull-down resistor (10kΩ is a common choice) between the gate of the MOSFET and ground to prevent the MOSFET from turning on unexpectedly when the ESP32 pin is in a high-impedance state (i.e., during reset or not actively driven).

Connecting the MOSFET:

Gate: Connect to ESP32, for example, U1:D5 (assuming D5 will be the control pin)
Drain: Connect to one of the waterpump terminals.
Source: Connect to GND.
Pump's other terminal: Connect to the positive side of your 5V power supply.

And, of course, do not forget to connect the ground of the 5V power supply to the ESP32's ground to ensure a common reference point for all components in your circuit.

pmamatis

can insert the Mosefets 2N7000 and already connect them to GPIOs of the ESP32?

copilot

Certainly! I'll guide you through inserting two MOSFETs of type 2N7000 into your project and connecting them to GPIOs of the ESP32 for control. Based on the list of available pins, I'll use D5 and D18 GPIOs for these connections. Let's assume each MOSFET will drive a separate water pump, requiring a control signal.

Project Update with 2N7000 MOSFETs

Components to Add:

Q1: 2N7000 MOSFET for water pump 1
Q2: 2N7000 MOSFET for water pump 2

Connections:

Connecting Q1 (MOSFET for water pump 1):
- Connect U1:D5 (GPIO for control) to Q1:Gate.
- Connect Q1:Drain to one terminal of water pump 1.
- Connect Q1:Source to U1:GND (common ground).
- The other terminal of water pump 1 should be connected to the positive side of the 5V power supply.
Connecting Q2 (MOSFET for water pump 2):
- Connect U1:D18 (another GPIO for control) to Q2:Gate.
- Connect Q2:Drain to one terminal of water pump 2.
- Connect Q2:Source to U1:GND (common ground).
- The other terminal of water pump 2 should be connected to the positive side of the 5V power supply.

Additional Components:

Make sure to add a pull-down resistor between the gate and source pins of each MOSFET to ensure they remain off unless explicitly driven by the ESP32:

R1: 10kΩ, connect between Q1:Gate and Q1:Source.
R2: 10kΩ, connect between Q2:Gate and Q2:Source.

This configuration ensures that the MOSFETs are in their OFF state when the ESP32 GPIOs are not actively driving them, preventing unintended water pump activation due to floating gate voltages.

Summary of New Connections:

Connect U1:D5 to Q1:Gate.
Connect Q1:Source to U1:GND, and Q1:Drain to Water Pump 1 (+ terminal).
Connect R1:1 to Q1:Gate and R1:2 to Q1:Source.
Connect U1:D18 to Q2:Gate.
Connect Q2:Source to U1:GND, and Q2:Drain to Water Pump 2 (+ terminal).
Connect R2:1 to Q2:Gate and R2:2 to Q2:Source.

Remember: The negative terminal of each water pump should be connected to the 5V power supply's ground, which must be shared with the ESP32's ground to complete the circuit.

Resistance

10kΩ

J1 P2 - U1 GND

Resistance

10kΩ

Resistance

10kΩ

J1 P2 - U1 GND

Resistance

10kΩ

Resistance

10kΩ

J1 P2 - U1 GND

Reviews

Ground
A common return path for electric current. Commonly known as ground.
jharwinbarrozo
20.5M
Net Portal
Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
jharwinbarrozo
43.0M
Power Net Portal
Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
jharwinbarrozo
11.4M
Generic Resistor
A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Capacitor
A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Inductor
A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
jharwinbarrozo
15.6k
Terminal
An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
natarius
RMCF0805JT47K0
47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
jharwinbarrozo
1.2M
875105359001
10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
jharwinbarrozo
1.2M
CTL1206FYW1T
Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
jharwinbarrozo
1.1M

Project Name

ESP32 waterpump interface

Description

Welcome to your new project. Imagine what you can build here.

Properties

Properties describe core aspects of the project.

Pricing & Availability

Distributor	Qty 1
Digi-Key	$2.51–$3.00
LCSC	$7.59
Mouser	$0.50

Assets

No assets added.

Controls

Welcome 👋

Flux helps you build PCBs faster with an AI teammate!

Create your account to collaborate, stay updated, fork your own version, and get instant answers from our AI agent.

pmamatis / ESP32 waterpump interface

Schematic