Schematic Symbol for L298N dual H-Bridge motor driver template...

Terminal
An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
natarius
Ground
A common return path for electric current. Commonly known as ground.
jharwinbarrozo
20.5M
Net Portal
A net identifier used to create connectivity to other Net Portal with the same designator. #portal
jharwinbarrozo
43.0M
Power Net Portal
Power net portal is a special schematic object used to define a power or ground net. Power ports allow you to conveniently indicate a power net at any location in the design. Power nets of the same designator automatically connect throughout your design #portal #power
jharwinbarrozo
11.4M
Generic Resistor
A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Capacitor
A generic fixed capacitor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Inductor
A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
jharwinbarrozo
14.4k
RMCF0805JT47K0
47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
jharwinbarrozo
1.2M
875105359001
10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
jharwinbarrozo
1.2M
CTL1206FYW1T
Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
jharwinbarrozo
1.1M

M_2

M_1

User Greeting Interaction

nagasrivaruntirukkovalluri

3 months

copilot

3 months

Using

General

Project

Layout

Hi there! How can I help you with your project today?

Ask for assistance

Start designing

Schematic help

Motor controller discussion

nagasrivaruntirukkovalluri

3 months

i want an curcuit diagram for automatic drainage cleaning system with components-NodeMCU ESP8266

Water Level Sensor

L298N Motor Driver (or L293D)

Water Pump Motor (DC)

Battery Pack (5V or 12V)

Wires for Connections,bread board

copilot

3 months

Using

General

Chat History

Project

Layout

Below is a summary recommendation for your schematic. Note that within Flux you’ll need to add these components to your schematic and wire them together according to the following guidelines:

Components to Add (with suggested links):

NodeMCU ESP8266
Water Level Sensor
L298N Motor Driver OR L293D Motor Driver (choose one based on your preference)
Water Pump Motor
Battery Pack

Schematic Recommendations:

Power Distribution & Grounding:
- Connect the battery pack’s positive output to the VIN (or appropriate power input) of the NodeMCU and the motor driver’s power input.
- Ensure all grounds (from the battery pack, NodeMCU, motor driver, and sensor) are tied together using the Ground component.
Water Level Sensor:
- Connect the sensor’s output to one of the NodeMCU’s GPIO pins (or analog input if available).
- Wire the sensor’s VCC and GND to the battery pack or regulated voltage as per sensor specifications.
Motor Driver Connection:
- Wire the control inputs of the chosen motor driver (L298N or L293D) to suitable GPIO pins on the NodeMCU.
- Connect the motor driver’s output to the water pump motor.
- Ensure the motor driver’s VCC is supplied appropriately (this may be the same battery pack or a separate regulator if needed).
Control Strategy:
- Program the NodeMCU so that when the water level sensor detects a specific level, it sends a control signal to the motor driver, thereby turning on the water pump motor.
Interconnections:
- Use wires (and optionally a breadboard for prototyping) to make the connections.
- Verify that the voltage ratings and current requirements of each component correspond to your chosen battery pack voltage (5V or 12V).

Before advising further, I have a quick clarifying question:

Which motor driver do you prefer for your design: L298N or L293D?

Feel free to answer or provide more details if needed, and I can help refine the schematic suggestions further.

Select L298N

Select L293D

Need more details

nagasrivaruntirukkovalluri

3 months

I'd like to use the L298N motor driver for this project.

copilot

3 months

Using

General

Chat History

Project

Layout

Below is an updated schematic recommendation using the L298N Motor Driver:

Components to Add:

Schematic Guidelines:

Power Distribution & Grounding:
- Connect the battery pack’s positive terminal to the power inputs of both the NodeMCU ESP8266 (ensuring proper voltage regulation, if needed) and the L298N Motor Driver.
- Tie together all ground connections (battery pack, NodeMCU, L298N, and sensor) using the Ground component.
Water Level Sensor:
- Connect the sensor’s VCC and GND to the battery pack (or a regulated voltage according to the sensor's specifications).
- Wire the sensor’s output to a GPIO (or analog) pin on the NodeMCU ESP8266.
L298N Motor Driver & Water Pump Motor:
- Connect the NodeMCU’s GPIO pins to the control inputs of the L298N Motor Driver to manage the motor direction and speed.
- Connect the output channels of the L298N to the Water Pump Motor.
- Ensure that the L298N receives proper logic power (which might be supplied by the NodeMCU or a separate regulator) in addition to the battery pack's supply to power the motor.
Control Logic:
- Program the NodeMCU to read the water level sensor. When a threshold is reached, it should trigger the L298N to drive the water pump motor.
- Verify the battery pack voltage (5V or 12V) is compatible with all components or use appropriate voltage regulators where needed.
Interconnections:
- Use wires and, optionally, a breadboard for prototyping, ensuring secure and reliable connections.

You can now use these guidelines to update your schematic in Flux. Let me know if you need help connecting specific pins or have further requirements!

Clarify further schematics

nagasrivaruntirukkovalluri

3 months

Let me know if you need help connecting specific pins or have any further requirements!

copilot

3 months

Using

General

Chat History

Project

Layout

Great! To assist you better, could you clarify which specific pin connections you'd like support with? For example, would you like help with:

Connecting the water level sensor to the NodeMCU
Connecting the NodeMCU to the L298N motor driver
Connecting the L298N to the water pump motor

Please let me know which one (or more) you'd like to work on, or if there's another specific connection you have in mind.

Connect sensor to NodeMCU

Connect NodeMCU to L298N

Connect L298N to motor

nagasrivaruntirukkovalluri

3 months

How about we start by connecting the water level sensor to the NodeMCU? Let me guide you through those connections.

copilot

3 months

Using

General

Chat History

Project

Great! Let's start by connecting the water level sensor to the NodeMCU ESP8266.

Before we proceed, I have 1 clarifying question to ensure the connections are exactly as you need:

Water Level Sensor Type: Is your water level sensor analog (typically with three pins: VCC, Output, GND) or digital?

Please let me know, or if you prefer, I can assume it's an analog sensor using the NodeMCU’s A0 (analog input) pin.

Assume analog sensor

Specify digital sensor

nagasrivaruntirukkovalluri

3 months

you only give curcuit diagram

copilot

3 months

Using

General

Chat History

Project

Below is a summary of the circuit connections for linking the water level sensor to the NodeMCU ESP8266. You can use these guidelines in Flux’s schematic editor to create your design.

Important: Flux does not support importing a complete drawn circuit diagram. Instead, you can add the sensor and NodeMCU components and wire them as described below.

Water Level Sensor to NodeMCU Wiring

Table

Water Level Sensor Pin	Connection	NodeMCU Connection or Supply	Notes
VCC	Connect to regulated supply (e.g., 3.3V)	NodeMCU 3.3V or external regulated supply	Ensure the sensor’s operating voltage matches
GND	Connect to common ground	NodeMCU GND and Battery Pack negative	Use the Ground component for a common ground network
Output (Analog)	Connect to analog input	NodeMCU A0 (analog input pin)	You may also add a voltage divider if needed based on sensor output range

This wiring summary represents the circuit diagram for the water level sensor connection. In your Flux project, add the Water Level Sensor and the NodeMCU ESP8266, then use wires to connect:

VCC: From the sensor to the 3.3V supply (or a regulated voltage compatible with the sensor).
GND: From the sensor to the common ground (using the Ground component), which is also tied to NodeMCU GND.
Output: From the sensor’s analog output to NodeMCU’s A0 pin.

Feel free to use this wiring guideline within Flux’s schematic editor for your design. Let me know if you need further assistance or additional connection details!

Water sensor to NodeMCU

Discuss L298N-NodeMCU link

Check for other questions

	Designator	Ruleset
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	＊`REF`＊	Override rule for ＊`REF`＊
	-	Remove REFs
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for Fab Shapes
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for Silk Shapes
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	＊`REF`＊	Override rule for ＊`REF`＊
	＊`REF`＊	Override rule for ＊`REF`＊
	-	Override rule for ＊`VALUE`＊
	-	Override rule for ＊`REF`＊
	-	Via size
	-	Override rule for Fab Shapes
	-	Override rules for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`VALUE`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Test Point 1.8mm Size
	-	Override rule for ＊`REF`＊
	-	Override rule for Fab Shapes
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Remove VALUEs
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`VALUE`＊
	-	Override rule for Silk Shapes
	-	Override rule for ＊`REF`＊
	-	Minimum Keep Out
	-	Override rule for ＊`REF`＊
	-	Override rule for Silk Shapes
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for ＊`REF`＊
	-	Override rule for Fab Shapes
	Layout

	Layer	Net
	All	GND, GND, GND, GND, GND, GND, GND, GND

	Name
	Trace 4c13

Welcome 👋

Flux helps you build PCBs faster with an AI teammate!

To use this component and get started with Flux sign up now.

paraggoyal / L298N dual H-Bridge motor driver template f1sE

Schematic

... show more