copilot

1. Design the Layout:
   • Design your entire schematic as a single PCB.
   • Ensure that the components and connections that should remain on the primary PCB and those on the break-away section are clearly separated.
2. Define the Break Line:
   • In the PCB layout editor, draw a straight line where you want the PCB to snap. Typically, this is done using routing tools or creating a board outline.
3. Add Perforations:
   • Use the "Drill" feature to add small holes along the break line. These are called "mouse bites." A common practice is to space these drill holes uniformly (e.g., 0.5 mm apart).
   • Make sure the diameter of the drill holes is appropriate (e.g., 0.5 - 0.75 mm).
4. Add Tabs for Stability:
   • Optionally, add PCB tabs (small connecting areas) that help hold the break-away section during manufacturing and transport.
   • These tabs can also have mouse bites drilled in them to make the snapping process easier.
5. PCB Design Considerations:
   • Ensure there are no critical traces or components crossing the break line.
   • Check that the mechanical stress of snapping the PCB won't damage nearby components.

1. Create the Board Outline:
   • Use the outline tool to define the combined shape of the two PCBs.
2. Draw the Break Line:
   • Use the line tool to draw the break line on the PCB layout.
   • Split the outline at this break line if necessary to create two separate board sections.
3. Add Mouse Bites:
   • Select the drill tool and place holes along the break line. For example, place holes every 0.5 mm with a diameter of 0.5 mm.
4. Review and Confirm:
   • Double-check the separation line to ensure it correctly divides the PCBs.

Plaintext
+------------------------------------------+
|  Full PCB                                |
|  Components for Main PCB                 |
|  +---------------+---------+-------------+
|  |               |         |             |
|  |               |         |             |
|  |   Components  | Mouse   |  Components |
|  |   for Main    | Bites   |  for Second |
|  |   PCB         | Line    |  PCB        |
|  |               |         |             |
|  |               |         |             |
+--|---------------+---------+-------------|
   |               |
   +---------------+

• Mouse Bites Line: consists of drill holes (like o o o o o)

Plaintext
------------------------ (Breakline)
o     o     o     o     o   <- 0.5 mm diameter drill holes equally spaced
------------------------

Plaintext
for i in range(number_of_holes):
    place_drill_hole($x_start + i * hole_spacing$, $y_position$)

• Ensure there's enough clearance around the break line.
• Run a design rule check (DRC) to ensure there are no violations.

pacheck

copilot

1. Outline the PCB: Start by defining the boundaries of your two PCBs within the Flux.ai editor.
2. Add Breakaway Tabs: These tabs connect the two PCBs and can be broken away after manufacturing. The tabs typically include small holes (mouse bites) or V-grooves that facilitate snapping.
3. Define Mouse Bites or V-Grooves:
   • Mouse Bites: Add small, evenly spaced holes along the break line. Each hole is usually around 0.5 to 0.75 mm in diameter and spaced about 0.75 to 1 mm apart.
   • V-Grooves: Utilize V-shaped grooves that cut halfway through the PCB on both sides, creating a weak line along which the board can be snapped.
4. Ensure Proper Component Placement: Make sure there are no components or traces running through the breakaway section. Place components at a safe distance from the break line.

1. Outline the PCB:
   • Create the PCB outline with two distinct sections for each PCB within the same board outline.
2. Create Breakaway Tabs with Mouse Bites:
   • Add small holes (mouse bites) on the breakaway tabs along the line you intend to separate the PCBs.

1. Define PCB Borders:
   • Use the PCB outline tool in the Flux editor to design the borders of both PCBs within a single panel.
2. Add Breakaway Tabs:
   • Within the outline, add tabs that connect the two PCBs. Tabs should be wide enough to support the PCB during the manufacturing process.
3. Mouse Bites Implementation in Flux:
   • Select the 'hole' tool on Flux.
   • Place small holes (diameter: 0.5-0.75 mm) along the breakaway line within the tabs.
   • Space the holes approximately 0.75 to 1 mm apart.
4. V-Grooves Implementation (if provided by your PCB manufacturer):
   • Some manufacturers allow the creation of V-grooves.
   • Define the V-groove along the break line within the panel.

__________________________________________
|                PCB 1                   ||   PCB Border
| ______________________________________ ||   Mouse bites (small holes) along the tab
||               |      Tab       |       ||
|| PCB 1 Area    |      (with     | PCB 2 ||
||               |      mouse     | Area  ||
||__________|     ____________|_______||
          $$mouse$$           $$mouse$$
          $$bites$$           $$bites$$

• Ensure there are no copper traces or critical components crossing the breakaway lines.
• Check with your PCB manufacturer to confirm the minimum tab width, hole size, and spacing for mouse bites or the feasibility of V-grooves.

copilot

1. Design the PCB Outline:
   • Define the outline for both PCBs within the same panel.
2. Add Breakaway Tabs:
   • Design small tabs connecting the two PCBs. These tabs will include the mouse bites that make them snappable.
3. Add Mouse Bites:
   • Use the hole tool to add small holes along the breakaway tabs, which will serve as the mouse bites.

1. Define the PCB Borders:
   • Use the PCB outline tool to draw the shape of your board.
   • Create separate regions within the same outline to represent each PCB.
2. Add Breakaway Tabs:
   • Within the outline, create small breakaway tabs that connect the two PCB sections.
3. Implement Mouse Bites:

1. Open Flux.ai and Load Your Project:
   • Open Flux.ai and load your PCB design project.
2. Define the PCB Outline:
   • Use the Outline tool to draw the overall shape of the PCB.
   • Create separate internal outlines connected by tabs where you plan the break.
3. Create Breakaway Tabs:
   • Draw small rectangles or tabs at the edges of the PCB that connect the two sections.
   • Make sure these tabs are strong enough to hold the PCBs together during manufacturing but can be snapped off after.
4. Add Mouse Bites:
   • Select the Hole tool in Flux.ai.
   • Place small holes along the tabs. Here’s a practical example:
     • Hole Diameter: 0.5 mm
     • Spacing: 1 mm
   • Align the holes in a row along the tab:
     • $ \bullet $ Place the first hole at one end of the tab.
     • $ \bullet $ Continue placing holes along the length of the tab, spaced about 1 mm apart.

_____________________________________________
|                PCB 1                      ||
|                                          ||
|__________________________________________ ||
||              |     Tab       |           ||
|| (Components) | (with mouse   | (Components) ||
||              |  bites holes) |           ||
||______________|_____________|___________||
        o o o o o
        Mouse bites

pacheck

copilot

1. Power Supply and Ground Connections:
   • Ensure that all power supply pins and ground pins of ICs and other components are properly connected.
2. Crystal Oscillator (X1) Connections:
   • The crystal is connected to the ATmega328’s XTAL1 and XTAL2 pins with appropriate capacitors C2 and C3. This seems correctly connected.
3. Voltage Regulator (U2 - 7805) Connections:
   • Verify that input voltage to the regulator (U2:VI) is appropriate.
   • Check the capacitors needed for voltage stabilization (none are explicitly mentioned).
4. LED (V2) Connection:
   • Ensure you have a current-limiting resistor in series with the LED to prevent it from burning out. None is mentioned.

1. Power Connections:
   • Connect C4:P2, U1:AVCC, U1:VCC, and U2:VO ensuring proper power distribution.
   • Connect C4:P1, U2:GND, and any other ground connections, ensuring a shared ground.
2. Microcontroller (U1 - ATmega328-PU) Pin Connections:
   • Ensure all necessary connections for the ATmega328, such as reset, crystal oscillator, and I/O pins, are correct.

1. Power Supply:
   • Ensure U2 is provided with a filtered input voltage.
   • Add decoupling capacitors:
     • Between U2:VI and GND.
     • Between U2:VO and GND.
   Here’s a common set of decoupling capacitors for the 7805:
   • Input Capacitor ($C_{in}$): 0.33µF
   • Output Capacitor ($C_{out}$): 0.1µF
2. Microcontroller:
   • Ensure U1 (ATmega328):RESET/PC6 is connected through a pull-up resistor (typically 10 kΩ) to VCC.
   • Connect U1:AVCC to VCC through a decoupling capacitor (~100 nF).
   • Ensure AREF is either connected to VCC through a capacitor or directly to AVCC, depending on use-case.
3. Oscillator:
   • Ensure that the capacitors connected to the crystal are of appropriate value, typically in the range of 18-22 pF.
4. LED (V2):
   • Add a current-limiting resistor (R):
     • Connect one terminal of R to U2:VO.
     • Connect the other terminal of R to V2:ANODE.
     • Connect V2:CATHODE to U2:GND.

• Voltage Regulator Capacitors:
  • Connect a 0.33µF capacitor between U2:VI and GND.
  • Connect a 0.1µF capacitor between U2:VO and GND.
• Microcontroller Reset:
  • Add a 10kΩ pull-up resistor between U1:RESET/PC6 and VCC.
• Current-limiting Resistor:
  • Connect R:1 to U2:VO.
  • Connect R:2 to V2:ANODE.
  • Connect V2:CATHODE to U2:GND.

copilot

• Potential Issues: Connecting two power sources simultaneously (one from the ISP and one from the external source) might lead to unexpected behavior or damage to your components.
• Voltage Levels: Ensure the voltage levels from the ISP programmer match the expected levels of the microcontroller's VCC.

• Disconnect External Power: When you connect the ISP programmer, simply disconnect the external power source.
• Current Supply: The ISP programmer will provide the necessary supply to the microcontroller through the VCC pin.
• Reconnection: After completing the programming, you can reconnect the external power source for normal operation.

• Disconnect External Power: Ensure the external power source to the voltage regulator (U2) is turned off or disconnected.
• Connect ISP Programmer: Connect your ISP programmer to the 6-pin port (J2).

• Connect J2:Pin_2 (VCC) to U1:VCC.
• Ensure GND on the ISP port (J2) is connected to U1:GND directly.

• Connect J2:Pin_2 (VCC) to U1:VCC directly.
• Connect J2:Pin_6 (GND) to Common GND.

• Disconnect the external power source feeding into U2:VI.

• Disconnect External Power: It’s safer and simpler to disconnect the external power source when using the ISP programmer.
• ISP VCC: Ensure VCC from the ISP port matches the microcontroller's VCC requirement.
• GND: Ensure a common ground connection for consistency.

1. Normal Operation: Use external power source (disconnect ISP programmer, keep connected to U2).
2. Programming with ISP Programmer: Disconnect external power, connect ISP programmer.

copilot

1. Identify Components to Replace:
   • Identify all the SMD components that you want to replace with THT components. In your case, these would be components like the capacitors $C1, C2, C3, C4, C5$, and the resistor $R1$.
2. Search for THT Footprints:
   • Search for equivalent THT footprints for each component. For example, instead of SMD_0603 for the capacitors, you might use a radial leaded capacitor package like RAD-0.1.
3. Update Component Footprints:
   • Update the package or footprint for each component in your design. Here's how to change them in Flux:
     1. Select the component to change.
     2. In the properties panel, update the package type to the THT equivalent.

• Currently: SMD_0603_1608Metric
• Change to: RAD-0.1 (or another suitable THT package)

• Currently: SMD_0603_1608Metric
• Change to: AXIAL-0.4 (or another suitable THT package)

1. Select $C1$ in your schematic.
2. In the properties panel, change the package from SMD_0603 to RAD-0.1.

1. Select $R1$ in your schematic.
2. In the properties panel, change the package from SMD_0603 to AXIAL-0.4.

• After changing the footprints in the schematic, you’ll need to rearrange the components on the PCB layout to accommodate the larger THT footprints.

• Ensure that all your connections still make sense with the new footprint. You may need to adjust traces to fit the new component sizes and lead widths.

• Verify that your Bill of Materials (BOM) reflects the new THT components to make ordering parts easier.

copilot

Mermaid
graph TD;

    PowerSupply["Power Supply - 7805 (U2 - MPN: 7805)"]
    Switch[Reset Switch $SW1$]
    Microcontroller[Microcontroller - ATMEGA328-PU $U1$ - MPN: ATMEGA328-PU]
    Crystal[Crystal Oscillator - LFXTAL036391Bulk $X1$ - MPN: LFXTAL036391Bulk]
    ResetPullUp[Reset Pull-Up Resistor $R1$ - 500 Ω]
    Capacitor1[Capacitor - ECQ-E4104JF $C1, C2, C3, C4$]
    DecouplingCap[$C5$ - SMD_0603_1608Metric]
    VoltageSource[Voltage Source $V2$]
    Connector1[$J2$ - PPTC061LFBN-RC]
    Connector2[$J3$ - PPTC061LFBN-RC]
    ExpansionHeader1[$J34$ - Expansion Header]
    ExpansionHeader2[$J35$ - Expansion Header]
    ExpansionHeader3[$J36$ - 61200621621]
    GND(1)[GND Net]

    PowerSupply --> Microcontroller
    PowerSupply --> Connector1
    PowerSupply --> Connector2
    PowerSupply --> Crystal
    PowerSupply --> ResetPullUp
    PowerSupply --> Switch
    PowerSupply --> ExpansionHeader1
    PowerSupply --> ExpansionHeader2
    PowerSupply --> ExpansionHeader3

    Switch --> Microcontroller

    ResetPullUp --> Microcontroller

    Microcontroller --> Crystal
    Microcontroller --> Capacitor1
    Microcontroller --> DecouplingCap

    VoltageSource --> PowerSupply
    VoltageSource --> GND(1)
    Crystal --> Microcontroller

    GND(1) --> PowerSupply
    GND(1) --> Microcontroller
    GND(1) --> Connector1
    GND(1) --> Connector2
    GND(1) --> ExpansionHeader1
    GND(1) --> ExpansionHeader2
    GND(1) --> ExpansionHeader3

    Connector1 --> Microcontroller
    Connector2 --> Microcontroller
    ExpansionHeader1 -.-> Microcontroller
    ExpansionHeader2 -.-> Microcontroller
    ExpansionHeader3 -.-> Microcontroller

copilot

1. Select Through-Hole Equivalent Components: Identify through-hole capacitors with similar electrical characteristics (capacitance, voltage rating, tolerance) to the existing SMD capacitors.
2. Update Footprints in Schematic: Replace the footprint of the SMD capacitors with the through-hole equivalent footprints in your schematic.
3. Update Designators if Needed: Ensure the designators remain consistent to avoid confusion, or adjust them if your design has specific naming rules for through-hole components.

• Old Part: SMD 0603 (1608 metric)
• New Part: Through-hole ceramic capacitor (e.g., radial or axial lead type)

• Original Connections:
  • Connect C1:P1 to Net $\text{(e.g., 24b49dd8b6c97d6dcb519c4b69e5b785)}$.
  • Connect C1:P2 to Net $\text{(e.g., 36009189a606201e1da46f1b1aa05ba2)}$.
• Updated Connections (Footprint changes only):
  • Through-hole capacitor C1 should still connect to the same nets at the same logical points in the schematic.

• C1: Updated from SMD_0603 to a through-hole radial lead ceramic capacitor.
• C2: Updated from SMD_0603 to a through-hole radial lead ceramic capacitor.
• C3: Updated from SMD_0603 to a through-hole radial lead ceramic capacitor.
• C4: Updated from SMD_0603 to a through-hole radial lead ceramic capacitor.
• C5: Updated from SMD_0603 to a through-hole radial lead ceramic capacitor.

1. Update the Footprint on Flux:
   • Select each capacitor in your design $C1, C2, C3, C4, C5$.
   • Update the package type from \text{SMD_0603_1608Metric} to the specific through-hole package $\text{(likely Radial or Axial)}$.
2. Re-route as Necessary:
   • After making these changes, you might need to re-route PCB traces connected to these capacitors to accommodate their new hole positions.

copilot