FM Transmitter Project Overview
3:29
Using Knowledge Base Tool.
Using BOM Tool.
Starting 6 component searches
Dispatching Library tool to find: "100nH Inductor"
Dispatching Library tool to find: "Varactor Diode"
Dispatching Library tool to find: "Trimmer Capacitor"
Dispatching Library tool to find: "Ferrite Bead"
Dispatching Library tool to find: "LDO 5V"
Dispatching Library tool to find: "ESD Diode RF"
Creating search plan for: "100nH Inductor"
Creating search plan for: "Varactor Diode"
Creating search plan for: "Trimmer Capacitor"
Creating search plan for: "Ferrite Bead"
Creating search plan for: "LDO 5V"
Creating search plan for: "ESD Diode RF"
Searching: "A generic ferrite bead used for EMI suppression and noise filtering on PCB power or signal lines. This search aims to identify standard ferrite beads typically employed for mitigating high-frequency disturbances."
Searching: "Ferrite bead components for electromagnetic interference (EMI) filtering in PCB applications. The target applications include both power line decoupling and signal line noise suppression, with potential impedance ratings specified at frequencies such as 100 MHz."
Searching: "Surface mount ferrite beads designed for high-frequency PCB applications. Focus on parts that offer defined impedance values (e.g., around 100 ohm at 100 MHz) and can support current handling suitable for EMI filtering in dense board layouts."
Searching: "High-specificity search for ferrite beads where the key specification is an impedance value measured at 100 MHz, ensuring effective suppression of high-frequency noise. Consider SMD package types and current rating details needed for power rail filtering in sensitive electronic designs."
Searching: "Searching for a low dropout regulator (LDO) that provides a steady 5V output voltage. This component is intended to power a 5V supply rail in a circuit requiring minimal voltage drop between input and output, ensuring reliable performance under load."
Searching: "Looking for a 5V low dropout regulator capable of delivering approximately 500mA. The part should provide a stable 5V output with low dropout characteristics, suitable for applications where efficiency and minimal voltage overhead are important."
Searching: "Searching for a 5V low dropout regulator in a TO-220 package, which is common for applications requiring higher power dissipation and ease of heatsinking. The device should provide a regulated 5V output for 5V rail power management."
Searching: "Targeting a 5V low dropout regulator rated for around 500mA current with a dropout voltage near 100mV. This highly specific search is for applications that require precise regulation in circuits where the difference between input and output voltage is minimal, ensuring efficient power management."
Found 75 results.
Searching: "Ferrite Bead"
Found 73 results.
Searching: "LDO 5V"
Searching: "Looking for a generic ESD diode component used to protect circuits against electrostatic discharge events. This search serves as a baseline to explore available ESD protection devices."
Searching: "Seeking an ESD diode specifically designed for RF applications. The part should have features optimized for high frequency signals, such as low parasitic capacitance and minimal insertion loss, to ensure signal integrity in RF circuits."
Searching: "Searching for an ESD diode with ultra low capacitance intended for RF circuit protection. The component must provide fast ESD protection while maintaining excellent high-frequency performance, making it suitable for sensitive RF signal lines."
Searching: "Looking for a diode that offers transient suppression for RF applications along with very low capacitance. The device should provide robust ESD protection in high-speed RF circuits while minimizing signal degradation and preserving frequency response."
Searching: "Looking for a basic varactor diode used in tuning circuits, such as VCOs or RF resonators. The device should offer variable capacitance based on applied reverse bias voltage, suitable for frequency modulation and tuning applications."
Searching: "Searching for a varactor diode designed for RF applications. The component is intended for use in high-frequency oscillator circuits and filters, with an emphasis on stable capacitance variation and low parasitic elements."
Searching: "Identifying a surface-mount varactor diode for compact circuit designs. Key requirements include a small footprint (e.g., SMD package), reliable tuning characteristics in oscillator or filter circuits, and compatibility with automated PCB assembly."
Searching: "Looking for a varactor diode with low leakage current and high Q-factor, which is crucial for precision RF tuning applications. This device should maintain stable capacitance over varied reverse bias voltages and contribute minimal noise in sensitive circuits."
Searching: "Targeting a high-quality factor (high-Q) varactor diode that offers excellent performance in applications such as voltage-controlled oscillators and tunable filters. The focus is on minimal losses and improved frequency stability in high-frequency designs."
Searching: "Searching for varactor diodes specified as voltage variable capacitor diodes, with detailed capacitance tuning ranges (for example, a capacitance range in the pF scale under varying reverse voltages) to support precise RF circuit implementations."
Searching: "Looking for a standard 100 nanohenry inductor used in high-frequency and switching power supply applications. This part should be suitable for PCB mounting and compatible with typical SMD packaging."
Searching: "Searching for a 100nH inductor in a surface mount package (e.g., 0603, 0805) intended for high-frequency filtering in power circuits and RF applications. Part should exhibit low parasitic losses and be compatible with modern PCB designs."
Searching: "Seeking a high-frequency rated 100nH inductor that can handle the fast switching typical of buck converters and RF circuits. Emphasis on low DC resistance and minimal core losses in a compact SMD form factor."
Searching: "Looking for a 100 nanohenry inductor optimized for buck converter applications. The part should have characteristics like low ESR, appropriate current handling, and a small SMD package suitable for PCB mounting in high-density designs."
Found 65 results.
Searching: "ESD Diode RF"
Searching: "Looking for a variable (trimmer) capacitor used for fine tuning or calibration in electronic circuits. This part would be adjusted manually to achieve precise capacitance values in analog or RF tuning applications."
Searching: "Searching for an adjustable capacitor that can be tuned post-assembly for precise circuit performance. The capacitor is intended for applications such as calibration, frequency tuning, or impedance matching in analog or RF circuits, and may be available in various mounting types."
Searching: "Focusing on surface mount (SMD) trimmer capacitors for PCB-mounted applications. The component should be compact and suitable for automated assembly while providing user-adjustable capacitance for calibration and fine-tuning in sensitive analog or RF circuits."
Searching: "Targeting trimmer capacitors designed for RF applications, where precision and stability are critical. The search entails parts with low parasitic elements and tight tolerance adjustments, ideal for high-frequency tuning, impedance matching, and sensitive calibration requirements."
Found 59 results.
Searching: "Varactor Diode"
Found 72 results.
Searching: "100nH Inductor"
Found 71 results.
Searching: "Trimmer Capacitor"
Completed 6 component searches.
- Goal: Take audio from an electret microphone, bias and couple it into a single‑transistor RF oscillator, and radiate the RF through an SMA antenna connector.
- Modulation approach: The audio from the microphone is injected into the transistor’s base bias, so the RF oscillator’s frequency and/or amplitude is modulated by the audio (direct FM/AM by bias modulation).
- Antenna interface: RF energy is AC‑coupled to the SMA end‑launch connector for an external antenna.
-
Power input and rails:
- J2 brings in DC power. In your nets, “Net 2” behaves as the positive rail and “Net 7” behaves like ground (J2:P1 ties to J1 shield and MK1 negative).
- Bulk decoupling: C6 (Panasonic ECA‑1HM101, 100 µF electrolytic) is placed between the positive rail (Net 2, +) and the RF collector node (Net 5, −). This provides low‑frequency energy storage but also ties directly into the RF collector node.
- Local ceramics: Multiple 0.1 µF ceramics (C1, C2, C3, C4, C5) are used around bias, feedback, coupling, and output.
-
Microphone input and bias:
- Mic: MK1 (PUI POM‑3042P‑R electret). MK1:N is on Net 7 (project ground), MK1:P is on Net 3.
- Bias: R4 (10 kΩ) ties Net 3 (mic output node) up to the positive rail (Net 2), providing the electret bias current.
- AC coupling to RF stage: C2 couples the biased audio from Net 3 to the transistor base node (Net 1).
-
RF oscillator/amplifier (single BJT):
- Active device: Q2 (2N2222 NPN).
- Base bias: R2 (10 kΩ) feeds DC bias from the positive rail (Net 2) to the base node (Net 1). C1 is connected between Net 2 and the base node, providing RF bypass at the base.
- Emitter network: R1 (10 kΩ) from the emitter (Net 4) to ground (Net 7), setting DC emitter bias. C4 connects the emitter (Net 4) to the collector node (Net 5), creating RF feedback.
- Collector/tank/output: The collector is on Net 5. C3 connects the collector to the positive rail (Net 2), and C5 AC‑couples the collector to the antenna feed line (Net 6).
-
Antenna and output coupling:
- Audio path: Voice/sound hits MK1. R4 biases the mic; the audio is AC‑coupled via C2 into the base node (Net 1). The base DC bias is set by R2, so the audio modulates the base bias.
- RF generation: Q2 and the feedback network around C3 and C4 constitute a capacitive‑feedback RF oscillator/amplifier. The exact resonant element setting frequency is not explicitly visible as a discrete inductor in the schematic; as drawn, the design appears to rely on stray/antenna inductance or is incomplete for a controlled LC tank. This has major implications for frequency stability and repeatability.
- RF output: The RF from the collector (Net 5) is AC‑coupled through C5 to the SMA center pin (Net 6) and out to the antenna. The SMA shell returns to Net 7 (ground).
- Single‑transistor RF stage:
- Pro: Very simple, minimal BOM, easy to assemble.
- Con: Frequency stability is poor without a defined inductor/tank and proper supply RF isolation; antenna loading can pull the oscillator; spectral purity is typically limited.
- Bias‑modulated audio injection:
- Pro: Minimal parts to achieve modulation.
- Con: Deviation and linearity are hard to control; without pre‑emphasis or audio conditioning, intelligibility on broadcast receivers can suffer.
- Through‑hole ceramic capacitors in RF path:
- Pro: Accessible and easy to solder.
- Con: Lead inductance can be significant at VHF; SMD NP0/C0G parts placed very close reduce parasitics and increase stability.
- End‑launch SMA:
- Pro: Clean 50‑ohm interface, good mechanical for test antennas or coax.
- Con: Without matching or a low‑pass filter, return loss and harmonic emissions may be poor.
- Frequency definition: No explicit inductor/tuned network is present in the schematic. Expect strong frequency drift, antenna pulling, and unit‑to‑unit variation.
- Supply pulling and RF feedback: The collector node is directly tied to bulk decoupling via C6. Without an RF choke in the DC feed, RF current can flow on the supply line, degrading stability and radiating unintendedly.
- Harmonics and compliance: Without an output low‑pass filter and matching, harmonic content and spurious emissions can be high. Real‑world operation may violate local RF regulations.
- Microphone loading: The electret requires correct bias and load impedance. Ensure the mic’s datasheet recommended load and coupling values are respected to avoid distortion or instability (design microphone circuits with datasheet‑compliant load and coupling).
- Layout sensitivity: RF oscillators are highly sensitive to parasitics. Long leads and loops in the tank path, base node, and collector output will impact frequency and startup.
- Suitable as a teaching/demonstration project for discrete RF oscillators and audio modulation.
- Not suitable for unlicensed broadcast unless operated within legal ISM constraints or with appropriate authorization and spectral control.
- Add a defined resonant tank and tuning:
- Use an explicit RF inductor in the collector or between collector and supply to form a known LC resonator: 100nH Inductor.
- Provide fine tuning with a variable capacitor such as LXRW0YV600-054 or 5.5-65pF Variable Film Capacitor.
- For electronic frequency control/deviation, add a varactor such as ZMV934ATA (or SMV1213-001LF) in the tank.
- Isolate the RF from the supply:
- Insert an RF choke or a high‑impedance feed into the collector supply path and decouple to ground locally; add a ferrite on the DC feed, e.g., 2506031017Y0.
- Supplement local decoupling with small ceramics right at the device (you already use 0.1 µF parts such as C3/C4; place them as physically close and as SMD NP0/C0G as possible in the final PCB).
- Regulate and clean the rail:
- If the source is a battery or noisy supply, use a low‑noise regulator (e.g., MCP1754S-5002xMB or a 7805 variant like L7805CV) and place additional local decoupling near Q2.
- Output filtering and matching:
- Add a 50‑ohm matching network and a low‑pass filter between C5 and J1 to reduce harmonics and improve power transfer.
- Consider an ESD protector on the RF port, e.g., TPD3E001DRLR, chosen for low capacitance.
- Stabilize and buffer:
- Add a small emitter‑degeneration resistor and/or adjust R1 to trade RF gain vs stability.
- Add a RF buffer stage after the oscillator so the antenna load does not pull the oscillator; this improves frequency stability significantly.
- Audio quality and broadcast compatibility:
- Add a simple pre‑emphasis network on the audio path if targeting FM broadcast receivers (and keep mic loading within datasheet guidance).
- Layout and documentation cleanups:
- Mic constraints: Follow the mic’s datasheet for bias current and load impedance (design microphone circuits to stay within recommended load and coupling; avoid over‑loading which can cause distortion/oscillation).
- RF layout discipline: Ground return management and decoupling placement dominate stability at VHF—treat the supply and ground geometry as part of the circuit.
- Regulatory limits: Any over‑the‑air operation must respect local laws; filtering and power limits are essential for compliance.
- As built, this is a minimal single‑BJT, microphone‑modulated RF transmitter with an SMA antenna port. It demonstrates the concept but lacks a discrete resonant inductor, supply RF isolation, and output filtering—so frequency stability and spectral purity will be limited.
- Adding a defined LC tank, supply choke/decoupling, output matching/filtering, an RF buffer, and careful RF layout will substantially improve stability, audio quality, and spectral cleanliness.
Ready.
Reviews
- Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portaljharwinbarrozo43.0M
- Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #powerjharwinbarrozo11.4M
- A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #genericsjharwinbarrozo15.1k
- An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.Terminal
- 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlinkjharwinbarrozo1.2M
- 10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcanjharwinbarrozo1.2M
- Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlinkjharwinbarrozo1.1M
Inspect
Transmisor FM
Controls
Properties
Availability & Pricing
| Distributor | Qty 1 | |
|---|---|---|
| Arrow | $6.42–$6.99 | |
| Digi-Key | $10.05–$14.03 | |
| LCSC | $10.38 | |
| Mouser | $13.21 | |
| Verical | $5.24–$8.14 | |
Assets
Welcome 👋
Flux helps you build PCBs faster with an AI teammate!
Create your account to collaborate, stay updated, fork your own version, and get instant answers from our AI agent.