Uploading Boar Pictures for Analysis
1:08
Planning the project.
Clarifying tool priorities.
Navigating tool priorities.
Creating the plan.
Finalizing the plan.
You want a 1:1 mechanical clone of the board in your photo. I’ve prepared a plan to execute that.
- Steps: collect precise photos/measurements, reconstruct the schematic from images, match parts/BOM, rebuild the single‑sided layout to original geometry, then run checks and export Gerbers/drill/BOM.
- Click Start on the plan bar to proceed.
Before we start, please provide:
- Orthographic top-side photo with a ruler for scale.
- Board width/height and hole locations.
- Potentiometer value/taper and shaft/bushing dimensions.
Plan
- Create a 1:1 mechanical clone of the existing single‑sided 'TENSION COMMAND BUFFER BOARD' as per the provided photo, preserving all mechanical features such as hole spacing, edge details, panel-mounted rotary control, and overall board size (38 mm x 45 mm). Reproduce the original schematic and copper layout so that the clone drops in mechanically.
#Implementation plan
- Documentation & Measurement
- Collect all available orthographic photos (top and bottom views) including close-ups of mechanical details.
- Record essential mechanical dimensions including hole locations, diameters, board thickness, edge interface details, and dimensions/specs of the panel rotary control.
- Schematic Reconstruction
- Reconstruct the original schematic from the photos, ensuring all component markings, nets, power rails, and interface connections are correctly identified and labeled.
- Compile a Bill-of-Materials (BOM) by identifying component values from visible markings and rework areas, and propose equivalent substitutes if necessary.
- PCB Layout Creation
- Set the PCB outline to 38 mm x 45 mm.
- Place mechanical features including mounting holes and the panel-mounted rotary control based on the measured dimensions.
- Replicate the single‑sided copper layout using airwires as guides to place components and route traces.
- Validation & Finalization
- Run Electrical Rule Check (ERC) and Design Rule Check (DRC) to ensure compliance.
- Generate manufacturing files including Gerbers, drill files, BOM, and assembly documentation.
#Success criteria
- All mechanical details (hole spacing, board dimensions, and panel rotary control) accurately reflected in the new design.
- The rebuilt schematic and PCB layout replicate the original board’s function and mechanical compatibility.
- Successful ERC/DRC completion and generation of complete fabrication files (Gerbers, drill files, BOM, assembly notes).
79 days
1:47
Clarifying dimensions for clone.
Planning user goals.
Deciding on tool usage.
Formatting the plan output.
Accessing knowledge base.
Performing tool calls for analysis.
You want a 1:1 mechanical clone of this board sized 38 x 45 mm. I’ve prepared a plan and it’s ready to execute.
Steps: capture orthographic photos and dimensions, reconstruct the schematic, identify parts/BOM, rebuild the single‑sided layout, run checks, and generate Gerbers/drill/BOM.
Before we start, please confirm:
- XY coordinates and diameters of both holes (from one corner).
- Value/taper and shaft/bushing sizes of the panel rotary control.
- Board edge interface pin count and pitch (or a straight-on photo with a ruler).
Click Start on the plan bar to begin; you can upload the top-side photo now.
Plan
- Create a 1:1 mechanical clone of the existing single‑sided 'TENSION COMMAND BUFFER BOARD' as per the provided photo, preserving all mechanical features such as hole spacing, edge details, panel-mounted rotary control, and overall board size (38 mm x 45 mm). Reproduce the original schematic and copper layout so that the clone drops in mechanically.
#Implementation plan
- Documentation & Measurement
- Collect all available orthographic photos (top and bottom views) including close-ups of mechanical details.
- Record essential mechanical dimensions including hole locations, diameters, board thickness, edge interface details, and dimensions/specs of the panel rotary control.
- Schematic Reconstruction
- Reconstruct the original schematic from the photos, ensuring all component markings, nets, power rails, and interface connections are correctly identified and labeled.
- Compile a Bill-of-Materials (BOM) by identifying component values from visible markings and rework areas, and propose equivalent substitutes if necessary.
- PCB Layout Creation
- Set the PCB outline to 38 mm x 45 mm.
- Place mechanical features including mounting holes and the panel-mounted rotary control based on the measured dimensions.
- Replicate the single‑sided copper layout using airwires as guides to place components and route traces.
- Validation & Finalization
- Run Electrical Rule Check (ERC) and Design Rule Check (DRC) to ensure compliance.
- Generate manufacturing files including Gerbers, drill files, BOM, and assembly documentation.
#Success criteria
- All mechanical details (hole spacing, board dimensions, and panel rotary control) accurately reflected in the new design.
- The rebuilt schematic and PCB layout replicate the original board’s function and mechanical compatibility.
- Successful ERC/DRC completion and generation of complete fabrication files (Gerbers, drill files, BOM, assembly notes).
Upload board photos
Provide hole measurements
Specify connector details
Potentiometer specs
Board thickness and copper
79 days
To get started, talk to Flux or create a New Document.
Welcome 👋
Flux accelerates your PCB design with AI.
Create your account to start using this component and bring your ideas to life.