This is a MP5048AGU-P module which mirrors the [EV5920-5048-V-00A reference design](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) You can utilize this module as many times as you like in your project without having to recreate the layout each time. #module #mps #smd #server

Lethal Company Pro Flashlight Broken Features: - U2M cannot be line powered from this circuit so the LED driver does not regulate. [Find the acompanying button board here](https://www.flux.ai/markwuflux/lethal-company-pro-flashlight-button-board) -Ultra bright -Makes click noise from speaker -Wirelessly transmits battery life (maybe use Ubo to receive this) -Drive a SST-40 Chinese LED I want this thing to be super bright! The brighter the better, but keep it simple. These LEDs will draw a lot of power, so we need some sort of CC source. It doesn't have to have high bandwidth. I am thinking about a DIY microcontroller buck converter with PID duty cycle control. Mistakes in this V1 design: - No pullup resistor on PG of Module1

This is a recreation of the [EV5920-5048-V-00A](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) from MPS which demonstrates a MP5920 Hot-Swap controller commanding 5 MP5048 e-fuses in parallel. WIP Items: -Routing In flux, this project demonstrates hierarchal design through the use of modules. Additionally, parametric symbols are used extensively to improve schematic cleanliness. Components in the canvas are locked because their positions correspond to the same positions as the original layout. Changelog from Original MPS Design: - Not including GPIO2 or GPIO3 as included in the original board due to NC pin name on the IC. - PC1 and PC2 footprints are 5mm in pitch and 12.5mm in diameter rather than the 16mm diameter in the original layout. This change corresponds with the selected part more accurately. -Renamed Designators to be More Verbose

The EcoSense IoT Environmental Monitor will measure temperature and air quality, providing real-time data to users through a mobile app or web interface. The device will be compact, easy to install, and user-friendly, offering insights into the indoor environmental conditions to promote health and well-being. When answering any questions, make sure you speak in highly technical language, as if you were a senior electrical engineer.

Here is the schematic of grove vision ai v2. with this you can edit and customize your vision sensor to incorporate with you own projects

Welcome to your new project. Imagine what you can build here.

I want to create a standard interface from my PCBs to my test equipment. My equipment: PSU: Rigol DP832 Scope: Siglent SDS 1202X-E WaveGen: Siglent SDG810 Logic Analyzer: DSLogic Plus 400MHz VNA: NanoVNA V2 6 scope channels (4 1X, 2 10X) 8 Logic Analyzer channels 1 Wavegen channel 4 Power Nets ( 2 pins each) (tie power nets to oscilloscope inputs) #template #testing

The Robo Project is a mobile robotic platform featuring a Particle Argon board, 4 motor-wheels controlled by L293D drivers, and an HC-SR04 ultrasonic sensor for obstacle detection. It's ideal for exploration, remote control, and robotics education. #allThingsRobotics #project #robot #L293D #car

Card edge pins for in-circuit serial programming without any parts.

A 3-bit counter showcasing digital logic simulation. Input is a sequence of pulses which pass through a logic block to determine the segments.

Build your own Modular LED Sign! This design prioritizes accessibility which means that the BoM can be ordered on Amazon and that everything was designed with solder-ability in mind. NOTE: This board is still an unfinished prototype that has not been built and verified. Operating Instructions: 1. [Important!] Power your buck converter and adjust the output voltage to 1.5V output before attempting to power the LEDs. If you cannot power the buck converter, just turn the potentiometer counterclockwise to its maximum setting.

A buck boost converter that can be powered from a Li-Ion battery and output 3.3V @ 500mA. Powered by the TPS63051YFFR and in the same package as a standard Adafruit buck converter. Expect to squeeze around 5-10% SoC from a typical Li-Ion battery. Input Voltage Range: 2.5V to 5.5V Assembled at pcbway.com

(Work In Progress) V3 of the Bee Hotel: Main goal is to be manufacturable by JLCPCB