Schematic Analysis and Design Issues

flux

1:01

General (prev)
Project
Below is an analysis of the provided schematic based on the actual connections and the reported airwire errors. Note that these issues are specific to the current schematic connections and component assignments:

Identified Issues and Recommendations

IssueExplanationRecommended Correction
Ambiguous net labelsThe nets are named “Net 1”, “Net 2”, and “Net 3” instead of using descriptive names (e.g. VIN, VOUT, GND). This can cause confusion when verifying proper interconnections.Rename the nets to something more descriptive. For example: assign U1:VI and C1’s corresponding pad to VIN, U1:VO and C2’s corresponding pad to VOUT, and U1:GND (and the remaining pads) to GND.
Duplicate pin naming on U1The LM1117 regulator (U1) shows two pads labeled VO (pins 2 and 4). Some datasheets indicate that multiple output pads are provided for thermal dissipation and current sharing, but the symbol must reflect that these output pads are internally tied.Ensure that the schematic symbol defines both VO pins as a common node – if not, merge them explicitly by labeling them identically. Verify this against the LM1117 datasheet.
Reported airwire error between U1:2 and C2:1The airwire error suggests that although C2:1 and U1:2 both belong to the output node, the tool is indicating an unconnected airwire. This could be due to the tool not recognizing the duplicate VO connection.Double-check that the symbol for U1 properly merges both output pads. An explicit net label (e.g. VOUT) can assist the tool in recognizing a single common node.
Reported airwire error between U1:3 and C1:1Similar to the output, the input side (U1:VI and its decoupling capacitor C1) is flagged. The error might indicate that the connection is made only by net naming without a proper explicit connection (e.g. a supply symbol).Verify that U1:VI is treated as the input node. It’s advisable to apply an explicit label such as VIN to both U1:VI and C1:1 to ensure the tool recognizes them as connected.
Reported ground airwire errors (e.g. U1:1 and C1:2, C2:2)Although C1:2 and C2:2 are on the same net as U1:GND, airwire errors are reported. This could be caused by the absence of an explicit ground symbol or a misinterpreted connection in the schematic editor.Add a dedicated ground reference symbol for the GND net and verify that all ground-related pads (U1:GND, C1:2, C2:2) use the same net label.
Additional Considerations
  • Decoupling Capacitors:
    Both decoupling capacitors (10µF) are placed across the input and output. For an LM1117 regulator, the datasheet typically recommends a low ESR capacitor placed very close to the device. Ensure that the layout minimizes trace lengths from the regulator’s pins to the capacitors.
  • Signal Integrity:
    The schematic does not include additional resistors (such as pull-ups or current limiting resistors); while not strictly required for a regulator, be sure that any further analog or digital interfaces downstream follow best practices (if added later).
  • Pin Assignment Verification:
    Verify the LM1117 pin assignments against its datasheet. In some packages, the pin order might vary; ensure that pin 1 (GND) is connected to the ground net and that the inputs/outputs are correctly assigned to the decoupling capacitors.
Next Steps
  1. Update Net Labels: Rename “Net 1”, “Net 2”, and “Net 3” to VIN, GND, and VOUT (or similar) as appropriate.
  2. Verify U1 Symbol:
    • Ensure that both VO pins (pins 2 and 4) are merged into one common node.
    • Confirm that the datasheet pinout matches the schematic.
  3. Add Explicit Ground Symbol:
    • Place a dedicated ground symbol on the schematic for GND to remove any ambiguity.
  4. Confirm Capacitor Placement:
    • Verify that the decoupling capacitors are placed as close as possible to U1’s pins in both the schematic symbol and the physical layout.
  5. Run a New DRC: After these corrections, run the design rule check again to verify that all airwire errors are resolved.
By applying these specific corrections, the schematic should better reflect the intended operation of the LM1117 regulator and its associated decoupling network while eliminating connection errors reported by the tool.
Rename nets descriptively
Confirm LM1117 symbol
Add explicit ground connection
Ensure datasheet adherence
Re-check DRC
327 days

Ready.

Sign up to send
C2
Capacitance
10u F
3v3
U1
C1
Capacitance
10u F
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • Power Net Portal
    Power Net Portal
    Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
    jharwinbarrozo
    11.4M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
    jharwinbarrozo
    15.1k
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • RMCF0805JT47K0
    RMCF0805JT47K0
    47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
    jharwinbarrozo
    1.1M

Inspect

LM1117 output regulator

LM1117 output regulator
Description

Created
Last updated by luisvieira
1 Contributor(s)
luisvieira

Controls

Properties

Availability & Pricing

DistributorQty 1
Arrow$0.43–$0.81
Digi-Key$0.49–$1.17
LCSC$0.18
Mouser$1.01
Verical$0.49–$0.60

Assets