kimuragabe/audio-electronics-or-copilot-preset: Use this Copilot's template to design audio...

Terminal
An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
natarius
Ground
A common return path for electric current. Commonly known as ground.
jharwinbarrozo
20.5M
Net Portal
A net identifier used to create connectivity to other Net Portal with the same designator. #portal
jharwinbarrozo
43.0M
Power Net Portal
Power net portal is a special schematic object used to define a power or ground net. Power ports allow you to conveniently indicate a power net at any location in the design. Power nets of the same designator automatically connect throughout your design #portal #power
jharwinbarrozo
11.4M
Generic Resistor
A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Capacitor
A generic fixed capacitor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Inductor
A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
jharwinbarrozo
14.3k
RMCF0805JT47K0
47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
jharwinbarrozo
1.2M
875105359001
10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
jharwinbarrozo
1.2M
CTL1206FYW1T
Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
jharwinbarrozo
1.1M

Can I put in code and it will create this?

@copilot Can I put in code and it will create this?

5mo

Yes, you can write code that defines and creates your audio electronics schematic and PCB layout in Flux. However, to get started, it will be most effective to define the main components and their connections first.

Let's break down your project requirements, define the components you will need, and establish the initial electrical connections:

Components

Class D Amplifier IC: For example, TDA8932 or TPA3116D2.
Bluetooth Module: For example, CSR8670 or ESP32-WROOM-32 for Bluetooth 5.0.
3.5mm Jack: Any standard audio jack with screw terminals.
Power Supply: 12V power supply circuit.
LED Indicators & Potentiometers: For volume control and status indication.

Suggested Connections

Bluetooth Module
- Connect ESP32-WROOM-32:Audio Left and Right pins to the input of the Class D Amplifier.
- Connect ESP32-WROOM-32:VCC to Power Supply:12V.
- Connect ESP32-WROOM-32:GND to Ground.
Class D Amplifier
- Connect TPA3116D2:INL to ESP32-WROOM-32:Audio Left.
- Connect TPA3116D2:INR to ESP32-WROOM-32:Audio Right.
- Connect TPA3116D2:VCC to Power Supply:12V.
- Connect TPA3116D2:GND to Ground.
3.5mm Jack
- Connect Audio Jack:Tip to TPA3116D2:Output Left.
- Connect Audio Jack:Ring to TPA3116D2:Output Right.
- Connect Audio Jack:Sleeve to Ground.
LED Indicators
- Connect LED Anodes to appropriate GPIO pins on ESP32-WROOM-32 for status indication.
- Connect LED Cathodes to Ground.
Potentiometer for Volume Control
- Connect Potentiometer:Wiper to TPA3116D2:Volume Control Pin.
- Connect Potentiometer:Terminal1 to Ground.
- Connect Potentiometer:Terminal2 to Power Supply:12V.

Using this information, you can start defining the connections in your Flux project. Here’s a code snippet to get you started, translated into netlist format:

Plaintext
* Create a schematic for an audio amplifier with Bluetooth input

* Power Supply
V1 N001 GND 12V

* Bluetooth Module
X1 N001 GND Audio_Left=Net1 Audio_Right=Net2 (ESP32-WROOM-32)

* Class D Amplifier
X2 Net1 Net2 Net3 N001 GND (TPA3116D2)

* 3.5mm Audio Jack
X3 Net3 GND Output_Left=Net4 Output_Right=Net5 Audio_Jack

* LED Indicators
D1 N002 GND LED1
D2 N003 GND LED2
D3 N004 GND LED3

* Potentiometer for Volume Control
R1 N005 N007 N008 Potentiometer

This specifies your components and their connections. You can import this netlist into Flux to create your schematic.

Would you like to proceed with any specific part of your schematic, or do you have any further requirements or questions?

5mo

Can I put in code and it will create this?

kimuragabe

Can I put in code and it will create this?

5mo

Hi! I’m Copilot, I’m here to help you design your hardware projects. Ask me anyt...

copilot

Hi! I’m Copilot, I’m here to help you design your hardware projects. Ask me anything:

@copilot can you partner up with me to design a PCB?

@copilot give me a few architecture options for an affordable Al pendant using mermaid diagrams.

@copilot how can I build a schematic with Flux?

To learn more, check out Getting Started with Copilot.

5mo

kimuragabe

Image

https://cdn2.flux.ai/flux-comment-files/files/commentFileId-ee4ac206599ea4a9860ad4f46e431f99efc590d595f9c51669596ed87d951f5b.png?GoogleAccessId=graviton-mvp%40appspot.gserviceaccount.com&Expires=4878977329&Signature=dfRbhQtWtXGyTq6%2F%2FNpfz18hGveyeS3VxQaZN%2ByZP51L0yRmmRQmZRzCYpbN5VrrT3rj%2FKbfnM4%2Boa%2F7NLBWRya5Wt9M2jjuDN4Gfy%2FyckM4U3z8lVGpvr%2BzACm62%2BLO%2F7cLvJrEW%2Fy5qtSDvZXBxYa2QX4icGvbRwo%2Bou9Dj1DsbiashlOo5bRCH59EXSR%2Felt4O47SG1sIFQC7rYQ2VOi%2Bo%2FPQ%2FVFQ6Ra0K484bEh%2BokqjOGe9Kk5aaGP8kM7SZ7Qf4l8BBEgVmKUdbmVICe4m%2BLVYUACNY4Fs3OrI95jp7T7tmRyD3eeCSDa41%2FCsONKTIzkI1mblNL6YjlBuyA%3D%3D

@copilot can you show me how to create this?

5mo

copilot

To create a positive diode clipping circuit like the one shown in the image, you'll need the following components:

Resistor ($R1$)
Diode (D1)
Input signal ($V_{in}$)
Output node ($V_{out}$)
Power supplies ($V_{+}$ and $V_{-}$)

Here's a step-by-step guide to build the circuit in Flux:

Add Components:
- Resistor $R1$
- Diode $D1$
- Input ($V_{in}$)
- Output ($V_{out}$)
- Power supplies ($V_{+}$ and $V_{-}$)
Connect the Components:

Connect the components as follows:
- Connect $V_{in}$ to one end of R1.
- Connect the other end of R1 to the anode of D1.
- Connect the cathode of D1 to $V_{out}$.
- Connect the anode of D1 and one end of R1 to $V_{-}$.
- Connect $V_{out}$ to $V_{+}$.

Here’s a concise version of the connections:

Connect $V_{in}$ to [R1]:1
Connect [R1]:2 to [D1]:anode and $V_{-}$
Connect [D1]:cathode to $V_{out}$
Connect $V_{out}$ to $V_{+}$

Circuit Explanation:

During the positive half cycle of the input waveform, the diode $D1$ becomes forward-biased if the voltage exceeds +0.7V (assuming a silicon diode with a forward voltage of approximately 0.7V). This clamps the voltage at $V_{out}$ to approximately +0.7V.
During the negative half cycle, the diode is reverse-biased, allowing the negative part of the input waveform to pass unchanged.

This forms a positive clipper circuit, limiting the positive voltage at the output to the diode's forward voltage drop and leaving the negative half-cycle of the signal unchanged.

Would you like to proceed with creating this circuit in Flux, or do you have any specific details or additional features you'd like to include?

5mo

Someone is typing...

Welcome 👋

Flux helps you build PCBs faster with an AI teammate!

To collaborate on this project, get the latest updates,
or fork your own version, sign up now.

kimuragabe / Audio Electronics | Copilot Preset

Schematic

... show more