TECHNICAL ASSIGNMENT AND DESIGN GUIDE Active Three-Way Crossover on NE5532 Powered by AM4T-4815DZ and Amplifiers TPA3255 (Updated Version)

MF: VISATON MR130

HF: Morel MDT-12

Each frequency range is amplified by a separate power amplifier: LF: TPA3255 in PBTL mode (mono)

MF + HF: second TPA3255 in stereo mode (one channel for MF, the other for HF)

The crossover accepts a single linear audio signal (mono) and divides it into three frequency bands: Range Frequency Range LF 0 – 650 Hz MF 650 – 2500 Hz HF 2500 Hz and above

Filter type: Linkwitz–Riley 4th order (24 dB/oct) at each crossover point (650 Hz and 2500 Hz). The crossover must provide: minimal self-noise;

no audible distortion in the audible range;

stable operation with NE5532 at ±15 V power supply;

easy adjustment of the level for each band, as well as the overall level (via the input buffer).

For all stages:

Cascade gain: K ≈ 1.586 This provides a Q factor of 0.707 (Butterworth), which in combination gives a Linkwitz–Riley 4th order.

Resistors: metal-film, tolerance ≤ 1%

The gain of each stage is set by feedback resistors:

Rf = 5.9 kΩ

Rg = 10 kΩ

K ≈ 1 + (Rf / Rg) ≈ 1.59

The circuit should allow for the installation of a small capacitor (10–47 pF) in parallel with Rf (footprint provided) for possible stability correction (not mandatory to install in the first revision). 3.2 650 Hz Filters (Low-frequency boundary for MF) These are used for the division between W250 and MR130. LP650 — Low-frequency Filter 2nd Order R1 = 24.9 kΩ

R2 = 24.9 kΩ

C1 = 10 nF

C2 = 10 nF

Two stages: LP650 #1 and LP650 #2. HP650 — MF High-frequency Filter 2nd Order Same values: R1 = 24.9 kΩ

R2 = 24.9 kΩ

C1 = 10 nF

C2 = 10 nF

Two stages: HP650 #1 and HP650 #2. 3.3 2500 Hz Filters (Upper boundary for MF) These are used for the division between MR130 → MDT-12. LP2500 — High-pass MF Filter R1 = 6.34 kΩ

R2 = 6.34 kΩ

C1 = 10 nF

C2 = 10 nF

Two stages: LP2500 #1 and LP2500 #2. HP2500 — High-frequency Filter Same values: R1 = 6.34 kΩ

R2 = 6.34 kΩ

C1 = 10 nF

C2 = 10 nF

Two stages: HP2500 #1 and HP2500 #2.

Additionally: U5 — input buffer / preamplifier (both channels)

If necessary, an additional NE5532 (U6) for the balanced input (see section 6.2).

All NE5532 should have local decoupling for power supply (see section 5.1).

Output: +15 V / –15 V, up to 0.133 A per side.

Maximum output capacitance: ≤ 47 µF per side (according to the datasheet).

5.1 Power Filtering Input (48 V): RC variant (simpler, acceptable for the first revision):

R = 1–2 Ω / 1–2 W

C = 47–100 µF (for 63 V or higher)

LC variant (preferred for improved noise immunity):

L = 10–22 µH

C = 47–100 µF

The developer may implement LC if confident in choosing the inductance and its parameters. Output +15 V and –15 V (general filtering): Electrolytic capacitor 10–22 µF per side

100 nF (X7R) per side to GND

Local decoupling for NE5532 (REQUIRED): For each NE5532 package: 100 nF between +15 V and GND

100 nF between –15 V and GND

Place as close as possible to the op-amp power pins (short traces). Additional local filtering for power lines: For each NE5532, decouple from the ±15 V main rails: Either 4.7–10 Ω resistor in series with +15 V and –15 V,

Or ferrite bead in each rail.

After this component, place local capacitors (100 nF + 1–4.7 µF) to ground.

Signal → series resistor Rin_series = 100–220 Ω

After resistor — capacitor Cin_RF = 470–1000 pF to GND This forms a low-level RF filter and reduces high-frequency noise.

DC-block (low-pass HP-filter):

Capacitor Cin_DC = 2.2–4.7 µF film in series

Resistor to ground Rin_to_GND = 47–100 kΩ Cut-off frequency — negligible in the audio range but removes DC.

Input buffer / preamplifier (NE5532, U5):

Non-inverting configuration.

Input — after DC-block.

Gain: adjustable, e.g.,

Rg_fixed = 10 kΩ (to GND through trimmer)

Rf = 10–20 kΩ + footprint for trimmer (e.g., 20 kΩ) The gain should be in the range of 0 dB to +10…+12 dB.

Possible configuration:

Rg = 10 kΩ fixed

Rf = 10 kΩ + 10 kΩ trimmer in series.

This allows adjusting the overall level of the crossover according to the source and amplifier levels.

Buffer output:

A low-impedance output (after NE5532)

This signal is simultaneously fed to the inputs of all filters:

LP650 (LF)

HP650 → LP2500 (MF)

HP2500 (HF)

6.2 Balanced Input (XLR / TRS) — Optional, but laid out on the board The board should allow for a balanced input, even if it’s not used in the first revision. Implementation requirements: XLR/TRS connector (L, R, GND) or separate 3-pin header.

Simple differential receiver on NE5532 (extra U6 package or use one channel of U5 if sufficient).

Circuit: classic instrumentation amplifier or differential amplifier:

Inputs: IN+ and IN–

Output — single-ended signal of the same level (or slightly amplified), fed to DC-block and buffer (or directly to the buffer if integrated).

Switching between balanced/unbalanced mode:

Implement using jumpers / bridges or adapters:

Either switch before the buffer,

Or use two separate pads, one of which is unused.

All balanced input grounds must be connected to the same AGND point as the unbalanced input to avoid ground loops.

A passive attenuator:

Series: Rseries (0–10 kΩ, adjustable)

Shunt: Rshunt to GND (10–22 kΩ, fixed or adjustable)

For simplicity and reliability:

Implementation on the board:

For each band (LOW, MID, HIGH) provide:

Pad for multi-turn trimmer 10–20 kΩ as a divider (between signal and ground) in the "level adjustment" configuration.

If adjustment is not needed — install a fixed divider (two resistors) or simply use a jumper.

It is preferable to use:

For setup: multi-turn trimmers 10–20 kΩ, available on the top side of the board.

Nominals for the initial configuration can be selected through measurements, but the PCB should have flexibility.

This provides: Accurate balancing of band volumes without interfering with the filters;

Flexibility for fine-tuning to the specific characteristics of the speakers.

1× Balanced input (XLR/TRS or 3-pin header) — optional, but space must be provided on the board.

Input impedance (unbalanced after RF-filter): 22–50 kΩ. The input tract must be implemented using shielded cables. 8.2 Outputs Outputs to amplifiers: Output Signal LOW OUT After LP650×2 (LF) MID OUT After HP650×2 → LP2500×2 (MF) HIGH OUT After HP2500×2 (HF)

Each output: Series resistor 100–220 Ω (prevents possible oscillations and simplifies cable management).

A nearby own AGND pad (ground output), so the signal pair SIG+GND runs together.

Outputs should be compactly placed on 2-pin connectors (SIG+GND) or 3-pin (SIG+GND+reserve).

Bottom layer: solid analog ground (AGND).

9.2 Component Placement Key principles: RC chains of each filter (R1, R2, C1, C2, Rf, Rg) should form a compact "island" around the corresponding op-amp. If elements are placed too far apart, the filter will not work correctly (calculated frequency and Q will shift).

Feedback tracks (Rf and Rg) should be as short and direct as possible.

The AM4T-4815DZ module should be placed:

Far from the input buffer,

Far from the first filter stages,

If necessary, make a "cutout" in the ground under it to limit noise propagation.

Place the input connector, RF-filter, and buffer on one side of the board, and the output connectors on the opposite side.

9.3 Ground The entire audio circuit uses one analog ground: AGND.

Connect AGND to the power ground (48 V and amplifiers) at one point ("star").

The star should be implemented as: One point/pad where:

The ground of the input,

The ground of the filters,

The ground of the outputs,

The ground of the DC/DC.

Avoid long narrow "ground" jumpers — use wide polygons with a single connection point. 9.4 Placement of Output Connectors Group LOW/MID/HIGH compactly.

Each should have its own GND pad nearby.

Route the SIG+GND pairs as signal pairs, avoiding large loops.

TP_LOW — LF filter output

TP_MID — MF filter output

TP_HIGH — HF filter output

TP_+15, TP_–15, TP_GND — power control

This greatly simplifies debugging with an oscilloscope. 10.2 Power Protection On the 48 V input — it is advisable to provide:

Diode/scheme for reverse polarity protection (if possible),

TVS diode or varistor for voltage spikes (optional).

10.3 Possible Stability Correction Pads for small capacitors (10–47 pF) in parallel with Rf in buffers and, if necessary, in some stages — in case of stability issues (this can be not installed in the first revision, but footprints should be provided).

NE5532 — 1–2 pcs (input buffer and balanced input) Total: 5–6 NE5532 packages.

Resistors (1%, metal-film): 24.9 kΩ — 8 pcs

6.34 kΩ — 8 pcs

10 kΩ — ≥ 12 pcs (feedback, buffers, etc.)

5.9 kΩ — 8 pcs

22 kΩ — 1–2 pcs (input, auxiliary chains)

47–100 kΩ — several pcs (DC-block, input)

100 kΩ — 1 pc (if needed)

100–220 Ω — 4–6 pcs (outputs, RF, protection)

4.7–10 Ω — 2 pcs for each op-amp or group of op-amps (power filtering) — quantity to be clarified during routing.

Trimmer Resistors: 10–20 kΩ multi-turn — one for each band (LOW, MID, HIGH)

10–20 kΩ — 1–2 pcs for the input buffer (overall gain adjustment).

Capacitors: 10 nF film — 16 pcs (RC filters)

2.2–4.7 µF film — 1–2 pcs (input DC-block)

10–22 µF electrolytic — 2–4 pcs (DC/DC outputs)

1–4.7 µF (X7R / tantalum) — 1 pc for local power filtering (optional).

100 nF ceramic X7R — 10–20 pcs (local decoupling for each op-amp)

470–1000 pF — 1–2 pcs (RF filter on the input)

10–47 pF — optional for stability correction (Rf).

Power Supply: AM4T-4815DZ — 1 pc

Inductor 10–22 µH (if LC filter) — 1 pc

R 1–2 Ω / 1–2 W — 1 pc (if RC filter).

Connectors: Input (RCA + 3-pin for internal input)

Balanced (XLR/TRS or 3-pin header)

Outputs LOW/MID/HIGH — 2-pin/3-pin connectors.

Check with a multimeter:

+15 V

–15 V

No short circuits in the power supply.

Install the op-amps (NE5532).

Apply a sine wave of 100–200 mV RMS (signal generator).

Check with an oscilloscope at TP:

LP650 — should pass LF and roll off everything above 650 Hz.

HP650 — should roll off LF, pass everything above 650 Hz.

LP2500 — should roll off above 2500 Hz.

**HP250

0** — should pass everything above 2500 Hz. 12.2 Phase Check The Linkwitz–Riley 4th order should give a flat frequency response when summed at the crossover points. This can be verified with REW/Arta. 12.3 Noise Check If there is noticeable "shshsh" or whistling: Check:

Grounding layout (star)

Placement and filtering of AM4T-4815DZ

Presence and proper installation of all 100 nF and local filters.

Check component values at least twice before soldering.

Filters should be routed as compact "islands" around the op-amp, do not stretch R and C across the board.

Always remember the rule:

"The feedback trace should be as short as physically possible." Before ordering the PCB, make a "paper prototype": print at 1:1, cut it out, place real components to check everything fits.