Heat Sensor Circuit Guidance

flux

2:28

General
Project
Knowledge Base
PHOTO-2025-12-10-19-10-56.jpeg

Clarifying circuit assistance.

Explaining component linking rules.

Analyzing the op-amp and circuit design.

Examining circuit components.

Using Knowledge Base Tool.

Planning circuit explanation and tips.

Got it. You’ve shared a “Heat sensor with fan cooling” circuit using a 741 op-amp. Here’s a concise walkthrough and a safer modern tweak if you plan to build it.
What the original circuit does
  • Reference rail: R5 + Z1 create about 10 V from the 12 V supply to power the LM741. This stabilizes the op-amp supply.
  • Temperature sensor: A forward‑biased 1N4148 diode acts as the sensor. Its forward voltage drops roughly 2 mV/°C, so as temperature rises, the sensed voltage changes.
  • Threshold set + hysteresis: VR1 (100 k) sets the trip point; R4 (100 k) feeds back a little of the output to add hysteresis so the fan doesn’t chatter near the threshold.
  • Output stage: The op-amp drives a PNP BD140 high‑side transistor through R6 (1 k). When hot, the op‑amp output pulls the base low, turning on the transistor and powering the 12 V fan. D2 across the fan is a flyback diode (use a 1N4007) to clamp motor transients. C1 (10 µF/16 V) decouples the rail.
Important build notes
  • Single‑supply 741 caveats: On single supplies you must bias signals within the op‑amp’s valid input range; do not assume ground is valid. The 741 has limited input common‑mode near either rail and limited output swing. In single‑supply designs, explicitly bias around mid‑rail and check output headroom and input headroom.
  • Orientation: Observe the sensor diode polarity, the flyback diode polarity (cathode to +12 V), and wire the BD140 as a high‑side switch (emitter to +12 V, collector to fan+, fan− to GND).
  • Calibration: With the fan off at room temp, adjust VR1 until the fan just turns on at your desired temperature, then back off slightly. Hysteresis from R4 will give a few degrees of separation between on/off.
If you’re going to build it today, consider this improvement
  • Swap the 741 for a single‑supply‑friendly part: LM358 (op‑amp) or, even better for thresholds, LM393 (comparator). These accept inputs down to ground and have outputs that are easier to interface, reducing edge‑cases around common‑mode and output swing.
  • Keep the rest the same: sensor 1N4148, flyback 1N4007, PNP BD140, C1 10 µF, VR1 100 k, etc. Or upgrade sensing with a 10k NTC Thermistor for a larger, more linear temperature swing.
Would you like me to recreate this in Flux as a small PCB, using LM358 or LM393, and add proper connectors for a 12 V fan and power input? If yes, tell me:
  • Keep the 1N4148 sensor or use a 10 k NTC?
  • Target turn‑on temperature and desired hysteresis (°C)?
  • Fan current (so I can size the transistor and traces)?
47 days

Ready.

Sign up to send
D_4
D_3
D_2
S_2
S_3
G
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • Power Net Portal
    Power Net Portal
    Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
    jharwinbarrozo
    11.4M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
    jharwinbarrozo
    15.1k
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • RMCF0805JT47K0
    RMCF0805JT47K0
    47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
    jharwinbarrozo
    1.1M

Inspect

IRF7410TRPBF

IRF7410TRPBF
Description

Created
Last updated by jecstronic
1 Contributor(s)
jecstronic

Controls

Properties

Manufacturer Part Number
IRF7410TRPBF
Manufacturer Name
https://www.infineon.com/
Designator Prefix
IC
Part Type
Integrated Circuit

Availability & Pricing

DPNStockQty 1
40–60K$0.3398–$0.623
14K$0.4144
2910–5.9K$0.2319–$0.9577
134$1.21
14K$1.70
1621–128K$0.3396–$0.621

Assets