Project Brainstorming and Requirements Outline

flux

1:53

General (prev)
Chat History
Project
Below is the final schematic wiring summary that incorporates all the previously discussed connections. You can now apply this final proposal in Flux using the "take action" button. This summary ensures that all components are correctly wired to power, ground, and signal nets as specified.

Final Schematic Wiring Summary

BlockFinal ConnectionsNet/Component References
Power Supply- 5V Regulator: Output connected to the “5V0” net with 0.1µF and 10µF decoupling capacitors tied to ground.- 5V Regulator → Net "5V0" - Decoupling Capacitors → Ground
- 3.3V Regulator: Output connected to the “3V3” net with similar decoupling capacitors.- 3.3V Regulator → Net "3V3" - Decoupling capacitors → Ground
Microcontroller & USB-Serial- ATmega328P: VCC pins tied to “5V0”, GND to common ground; all analog inputs connected to sensor interface nets.- ATmega328P → Powered from "5V0" - All MCU grounds → Ground
- FT232RL: VCC from “5V0”, GND to common ground; TX connected to MCU RX and RX to MCU TX.- FT232RL → Wired to corresponding UART pins on ATmega328P
Digital Switches- Each of the 8 push buttons has one terminal connected to a designated MCU digital I/O pin.- Use existing B3FS-1050P symbols (or add if missing).
(with RC networks)- For each switch, add an RC network (a series/parallel combination of a resistor and capacitor) between the MCU I/O and ground for debouncing.- Generic Resistor and Generic Capacitor used for each debounce network.
LDR Sensor Interface- The adjustable voltage divider is built from an LDR07 at the top (tied to “5V0”), a potentiometer, and a resistor to ground.- Divider midpoint tapped to an ATmega328P analog input - Potentiometer example: 3386P-1-103LF
LM35 Temperature Sensor- LM35 output connects to an MCU analog input.- Low-pass RC filter (resistor in series & capacitor to ground) inserted between sensor output and analog input.
ADXL335 Accelerometer- Each axis (X, Y, Z) from the ADXL335 is routed separately to dedicated MCU analog inputs.- Optionally add a series resistor and capacitor (for each channel) for additional signal conditioning.
LED Driver & LEDs- A transistor array or dedicated LED driver circuit controls 10 single-color LEDs plus 3 RGB LED modules.- Each LED is connected with its current-limiting resistor in series - Driver outputs routed to LED nets (refer to the designed LED driver circuit wiring)
7-Segment Displays- Two 7-segment displays (common cathode or common anode per your design) are connected in a multiplexed drive arrangement from the MCU.- Each segment uses a current-limiting resistor - Common pins (anode or cathode) are connected to “5V0” or ground, as required by the display type.
16x2 LCD Display- The HD44780-based 16x2 LCD display is wired with VDD connected to “5V0”, VSS to ground, and data/control lines connected to designated MCU pins.- Ensure proper contrast adjustment (with a potentiometer, if needed) and backlight connections as per the LCD datasheet.
Motor Driver (L298N)- The L298N module’s VCC is tied to “5V0” and GND to the common ground.- Motor driver inputs connected to appropriate digital outputs from the ATmega328P - Motor outputs wired to the motor load.
Relay Driver- A transistor-based relay driver circuit (including resistor and flyback diode) is connected to a dedicated digital output from the ATmega328P for relay actuation.- Relay driver transistor circuit connects its output to the relay control input - Include connections from MCU to driver, and driver output to the relay module.
Implementation Steps in Flux
  1. Place/Verify Components:
    • Confirm that all the required parts (regulators, sensors, ATmega328P, FT232RL, displays, L298N, etc.) are in your project. Use Flux search links to add any missing components.
  2. Assign Net Names:
    • Label the net from the 5V regulator as “5V0” and the output from the 3.3V regulator as “3V3.”
    • Use a common Ground net for all ground connections.
  3. Create Signal Connections:
    • Wire the power and ground connections as described, then connect the signal paths from the sensors, switches, and peripheral interfaces to the appropriate MCU pins.
  4. Insert Passive Elements:
    • Add the debouncing RC networks for each switch, and install filtering RC networks for the LM35 and ADXL335 interfaces.
  5. Connect Peripherals:
    • Wire the LED driver block, multiplexed 7-segment display connections, and the LCD display according to the outlined connections.
  6. Review and Run ERC:
    • Once all components are wired, execute an Electrical Rule Check (ERC) in Flux to confirm all power, ground, and signal nets have been correctly assigned without errors.
Take Action:
Click the "take action" button in Flux to finalize these schematic connections. This will update your project schematic with wiring that connects each component exactly as outlined in this final summary.
All connections have been reviewed against the guidelines to ensure proper wiring to power, ground, and relevant signal nets.
310 days

Ready.

Sign up to send
how do I connect U1 and D1?
hasofukirsch

hasofukirsch

@copilot how do I connect U1 and D1?
10mo

copilot

To connect the ATMEGA328PB-AU ($U1$) and the HDSM-431W ($D1$), you can use the GPIO pins on the microcontroller to control the segments and the common anode of the 7-segment display. Here’s how you can connect them:
  1. Segments a-g of the 7-segment display:
    • Connect $U1$:PD3 to $D1$:a
    • Connect $U1$:PD4 to $D1$:b
    • Connect $U1$:PD5 to $D1$:c
    • Connect $U1$:PD6 to $D1$:d
    • Connect $U1$:PD7 to $D1$:e
    • Connect $U1$:PB0 to $D1$:f
    • Connect $U1$:PB1 to $D1$:g
  2. Decimal Point (dp):
    • You can choose to control the decimal point as needed by connecting it to another available GPIO pin on the microcontroller, such as:
    • Connect $U1$:PB2 to $D1$:dp
  3. Common Anode (CA):
    • The common anode should be connected to the positive voltage supply.
    • Connect $D1$:CA to the supply voltage you intend to use, such as the 5V supply if it’s within the forward voltage range of the display segments.
  4. Resistors:
    • Make sure to use current limiting resistors between each microcontroller pin and the corresponding segment pin on the 7-segment display to prevent excess current from damaging the segments.
These connections allow you to control each segment of the display by sending appropriate logic levels from the microcontroller to the display. Let me know if you have any specific requirements or if there are other components you'd like to include!

1

10mo
Someone is typing...
how do I connect U1 and IC1?
hasofukirsch

hasofukirsch

@copilot how do I connect U1 and IC1?
10mo

copilot

To connect the ATMEGA328PB-AU labeled as U1 with the FT232RL-REEL labeled as IC1 for UART communication, you would typically make the following connections:
  • UART TX and RX:
    • Connect U1:TXD $PD1$ to IC1:RXD (pin 5).
    • Connect U1:RXD $PD0$ to IC1:TXD (pin 1).
  • Power Connections:
    • Connect IC1:VCC (pin 20) to a suitable power supply, such as 5V or 3.3V.
    • Connect IC1:VCCIO (pin 4) to the same voltage level as the microcontroller.
  • Common Ground:
    • Connect U1:GND (pin 5 or pin 21) to IC1:GND (pin 7, 18, or 21) to ensure a common ground reference.
  • Reset (Optional):
    • Connect IC1:RESET (pin 19) to U1:RESET (pin 29) if you wish to allow programming and serial debugging functionalities.
Make sure to check the datasheet of FT232RL to match the correct pin functions and power requirements with your design needs. Let me know if you need any more assistance!
10mo
hasofukirsch

hasofukirsch

yes i was hoping you would connect them if i pressed a button
10mo

copilot

To enable UART communication between U1 and IC1 when a button is pressed, we can integrate one of the switches from your project, such as SW1, which you can use as a trigger.
Here's how you can set up the connections:
  1. Connect the Button:
    • Connect SW1:P1 to GND to ensure the button has a reference to ground.
    • Connect SW1:P2 to a spare digital pin on U1 to detect the button press. Let's use U1:PD2 (pin 32) for this purpose.
  2. UART TX and RX (controlled by the button):
    • Normally, you could set up your software logic such that the connection between U1 and IC1 is only enabled when this pin is detected as being pulled low due to a button press. This setup involves writing firmware on the microcontroller to control its TX/RX behavior based on this input.
  3. Power Connections:
    • Always connect IC1:VCC (pin 20) to the appropriate power supply and IC1:VCCIO (pin 4) to the same voltage level as the microcontroller.
  4. Common Ground:
    • Connect the microcontroller's ground as previously mentioned to ensure all parts share a common reference signal.
You can implement conditional logic in your microcontroller firmware to make UART communication appear to be controlled by the button press from SW1. If desired, I can offer some suggestions about how that logic might be structured. Let me know if you need more information!
10mo
Someone is typing...
2
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • Power Net Portal
    Power Net Portal
    Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
    jharwinbarrozo
    11.4M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
    jharwinbarrozo
    15.1k
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • RMCF0805JT47K0
    RMCF0805JT47K0
    47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
    jharwinbarrozo
    1.1M

Inspect

Arduino Board Request

Arduino Board Request
Created
Last updated by hasofukirsch
1 Contributor(s)
hasofukirsch

Controls

Properties

Availability & Pricing

DistributorQty 1
Arrow$19.17–$28.17
Digi-Key$46.43–$65.23
LCSC$67.19–$69.35
Mouser$49.87
Verical$21.97–$34.92

Assets