The clamp hardware is now modeled without drilling the block or changing the supports. But I can’t call the restraints complete: the lead paths still need local bends into the clamps, and no wire-contact liner or safe grip size is established. I’m checking the added hardware and preservation claims, then I’ll stop this pass with those limits clearly stated.
Thought for 2 mins 23 sec
3 days ago
"Wire Restraint Verification" completed.
Thought for 9 mins 48 sec
3 days ago
"Wire Restraint CAD Fix" completed.
Thought for 6 mins 48 sec
3 days ago
"Wire Restraint CAD Fix" completed.
Worked for 36 sec
flux
3 days ago
The screw-operated clamp hardware is modeled, but actual wire retention is not yet established.
I added a clamp assembly around the existing rear support, with separate heater, sensor and cutoff jaws. The latest repair:
Routes three planning lanes through the jaws without the earlier hardware collisions.
Moves the collar screw clear of the stand by 2 mm.
Preserves the electronics, completed supports, panels and current board poses.
These are closing clamp mechanisms, unlike the earlier open guides. However, no wire-contact liner or compatible grip dimensions are established. Heater-lead diameter, allowable compression, bend limits and safe first-support distance remain unresolved. The heater’s first strain relief cannot yet be called complete.
The final repair has reported geometry checks, but I could not independently recheck it before execution stopped. Copper Clearance remained ignored. Nothing is approved for fabrication or heating.
2026-11-12: carrier is now the second editable layout "Control Panel Carrier" in this project. See the second layout migration record doc. The child project is a backup only.
Current parent mechanical follow-up
Supersedes earlier axial poses below: carrier finished front/rear n=-22.6/-24.2186mm, core -22.66/-24.1586; encoder front/rear -16/-17.6 on5mm nylon; OLED front/rear -6/-7.6 on15mm nylon. Centers and child holes unchanged. Through-bolts/nuts and insulating washers replace opposing screws. Parent now has bolted hidden frame supports and a relieved encoder rear-PCB compression backstop. No child/copper mutation.
Current
3D Model
, cable repair report, sources/checks and replay inputs. Nominal200mm bows now meet15mm minimum radius, including separately solved195/205mm stock alternatives; two bolted loose guides are installed. Rear J2(-6,17)/J3(12,17), rot0, are unchanged. No connector relocation approval is required. Final local195mm OLED bow reshape now provides1.198464mm exact support clearance, versus the independent review's original0.371317mm. The old0.05368mm mesh lower bound is superseded. No support walls or hardware changed. Exact keyed mating/OD/bend/fatigue and other physical qualification remain held. Current
3D Model
,
3D Model
, and local final evidence supersede earlier cable revision links. No manufacturing/heater release.
The source-current selected-set candidate is now placed in parent Selected controls: carrier core front n=-22.6 mm, rear -24.0986, nominal module front/rear -16/-17.6; preserve u/v centers and native board data. Parent O=(0,-57.5,61.5), thetaX67.1354918781°, scale1, direct per-model transforms verified in the rendered scene. Historical control carrier v2 is retained disabled (active=false), not the selected assembly. No main-board copper/placement or shell cut changed.
3D Model
and mechanical preparation enumerate the 125 nominal solids, separate hardware, black knob source, measured clearances, editable bundle and limitations. Carrier depth is a nominal candidate, not a qualified production stack. Eight source-based spacers, sixteen screws, bezel/adhesive and a bounded rear cradle are modeled; frame anchorage and the complete encoder push-load path remain unfinished. Cradle is not a proven support. The opposing M2×4 screws have only0.0986mm nominal tip gap before finish/tolerances: hardware stack is not released. Glass now has n=-14.55 front, with off-axis readability unchecked.
Completed panel checks give encoder0.5mm, knob2mm, bezel0.13mm, each zero common volume. Cables/plugs/clips and press/service sweeps remain unmodeled; no global fit PASS. Child remains at source-current PH placement and8 intentional airwires; no routing. Parts stay326/5880/5527/two4424. Parent schematic/master BOM reconciliation and electrical qualification remain open; heater DO NOT ENERGIZE. Older 'not yet placed' statements and4991/377 depths below are superseded by this section.
2026-11-12 approved 5880 / 5527 / 4424 selection — current
The user approved 326 OLED, presoldered 5880 encoder, black 5527 set-screw knob, two 200 mm 4424 PH-SH leads and rear PH headers. The approved bezel and control centers remain unchanged. Selected mechanical preparation includes the 5880 datum arithmetic, shaft-only Ø7 hole, provisional support/load path, independent bezel model and separate broad-bend rear loom reservations. The old 4991/377 model, which omits installed cables, is still the displayed v2 and is explicitly superseded as a hardware selection, not yet replaced as a model; do not call it the approved assembly. Old Rev C SH socket moves below are superseded by rear PH replacement and must not be applied. The child source-current export and actual connector poses are awaited; no carrier depth, bracket or cable fit is released. Heater and upstream harness HOLD remain.
Historical 2026-11-12 supplemental carrier reconciliation — model v2 before selected 5880 hardware
The parent now references
3D Model
: 123 valid solids, the previous 115 plus eight representations (six nominal library packages, two sourced envelopes). Its unchanged STEP bounds are X=10…115, Y=−52…−10, Z=−7.285…29.5986 mm. The datum and prior parts are unchanged; the node preserves the previous unit-scale pose. See supplement audit and verification. The added shapes were screened against the previous assembly and one another; the full parent-shell fit was not rerun with the eight additions. The historic fit results below remain tied to v1 only, not a v2 fit pass. Plug bodies, cables, terminals, fasteners and knob are still missing and qualification remains open.
The child remains unrouted with 12 airwires and two outside-board QT socket flags. Proposed Rev C socket moves are not applied: J2 (−6,−5.5) top 90°, J3 (12.9,5.5) top 270°, and removal of only their respective edge-placement rules await explicit approval. Approved control centers and bezel remain unchanged. Conceptual cable paths cross at 0.793 mm centerline spacing before cable diameter: not a fit or service pass.
Electrical verification rev C bounds carrier current at 81.2 mA and known parent external load at 86.3 mA, leaving 213.7 mA of the 300 mA recommendation for optics and other unknowns. I²C sink bound is 1.82 mA/line under its stated voltage assumption. Internal OLED and NeoPixel operating-voltage limits are not guaranteed; the parent rail bound is an assumption, not a measured guarantee. Use 3V3, never 5V, and mate/unmate only with power off. No electrical, routing or physical-fit release. Parent schematic representation, BOM and full cross-board reconciliation remain open. HEATER DO NOT ENERGIZE; upstream harness remains HOLD.
2026-11-12 focused fastening, tolerances and reproducibility addendum
PROVISIONAL — neither a cut instruction nor installed hardware qualification. The user already approved the 42 × 30 mm surround, 30 × 22 mm opening, and preserved control centers; these are not reopened. This addendum bounds the remaining interfaces without moving controls or routing either board.
Encoder clamp and printed panel
The Bourns PEC11 drawing identifies the exact 15 mm flatted-shaft variant's LB=5.0 mm, M7 × 0.75 bushing and an included washer and nut, but gives neither nut/washer dimensions nor a bushing thread tolerance class. It lists maximum mounting torque 10.2 kgf·cm (approximately 1.00 N·m): a device limit, not an installation torque for printed PETG. Nominal shoulder-to-free-thread at a 3.0 mm panel is 2.0 mm before hardware. For a sourced SANNI M7 × 0.75 accessory-nut drawing, the 1.3 mm high option (Ø9 mm nominal) leaves 0.7 mm length nominally; 1.3/0.75≈1.73 nominal thread pitches across the nut. This is an alternative dimensional candidate, not a confirmed separately purchasable nut, the Bourns-supplied part, or proof of usable full-thread engagement/strength. Confirm nut entry chamfers, thread runout, start and free protrusion and obtain the exact part before adopting. The Accu HPW-M7-A2 washer is 7.4 mm ID, 14 mm OD and 1.8 mm thick nominal (1.4–1.8 mm listed). It does not fit this stack with the 1.3 mm nut: at nominal thickness 5−3−1.8=0.2 mm remains for the nut; even minimum washer thickness leaves only 0.6 mm. Do not use it here. A thin compatible bearing washer or integral flange may be investigated only with its dimensions and remaining thread measured; washer omission alone does not prove PETG bearing strength or creep resistance.
The operating push load path must be shaft → encoder body/bushing → engaged exterior mounting nut → panel bearing face → panel/frame; the OLED glass and board-to-module solder joints must not carry that load. Tightening, pull-through, repeated press and creep, and nut-to-knob sweep remain unverified. Install the encoder without forcing the independently supported 4991 module to an incompatible hard spacing. The knob must clear the actual nut during its complete 0.5±0.2 mm travel; 450-BA761 bore depth is not inferred from its 4.5 mm D-flat dimension.
For a test coupon, propose a finished Ø7.5 ±0.1 mm hole, not a CAD or cutting release. Assuming only an actually measured bushing maximum ≤7.0 mm, worst-case concentric radial clearance is (7.4−7.0)/2=0.20 mm; all hole-position error, bushing runout and PCB/shoulder misalignment must fit inside that 0.20 mm budget, with a positive residual margin. If measured bushing maximum differs, recalculate from actual maximum. The prior Ø7.4 proposal remains an uncut concept and gives no such tolerance allowance unless its finished size is controlled. The approved panel process is translucent PETG, 0.4 mm nozzle; printer-specific hole calibration, ovality and finished hole location require coupons. The generic process fallback is +0.5 mm screw clearance and +0.2 mm for small horizontal-hole sag, not a universal PETG accuracy guarantee. Hole direction, 3 mm thickness, remaining ligament, print orientation, press/load and long-term creep need verification before selecting a final CAD hole.
Carrier supports and independent decorative bezel
Four native carrier holes H1–H4 read back at panel coordinates (−46,±17) and (+51,±17) mm. A candidate is the catalog-listed RAF M3 female-female 13 mm standoff, 6 mm hex. The 13.1 mm nominal panel-inside-to-carrier-face separation leaves 0.1 mm, so an independently sourced Schumacher U4351 3.2 × 6 × 0.1 mm shim is a trial take-up, not a tolerance strategy. The test uses a conservative Ø6.9282 mm circumscribed envelope for a 6 mm across-flats hex, not a representation of real screws, threads or an installed part. At all four holes, exact static tests against the partial carrier and panel found 0 mm³ common volume and a 0.1000–0.1002 mm gap to the panel for a 13.0 mm test standoff. This does not establish drilled panel holes, thread depth, screw length, electrical isolation, wrench/head clearance, shim fit, support strength, actual board thickness or push loading. Structural support remains a proposed four-point bolted stack to the panel/frame, with loads and hole positions to be verified; no panel holes were cut and no fabricated standoffs or screws are represented as installed. See envelope source and results.
The approved bezel is decorative and must not be the encoder's push-load path or press on glass. The existing 36 × 24 mm panel aperture inside the 42 × 30 mm bezel leaves a nominal 3 mm bonding land each side, area 42×30−36×24=396 mm² before corners and tolerances. 3M 9472LE is a sourced 0.13 mm transfer-adhesive candidate, not proof of adhesion to as-printed PETG or a released fastening choice. Verify flatness, actual printed surface treatment and coupons (including peel, handling, creep and temperature) before adopting; adhesive contact must avoid glass and opening. Bezel and supports were not placed as supposedly installed solids because hardware engagement, actual bearing/adhesive stack and panel holes are unresolved. This retains approved appearance without asserting an unsafe load path.
Bounded outboard QT test — not cable clearance
A reproducible ideal cylinder of Ø1 mm was extended outward in ±u from the modeled socket origin, at its stored v,n, against the modeled shell only. It represents no real plug, wire, service sweep or required bend radius. For OLED-left x=−39.291 mm child, 25 mm reaches u=−61.791, or 11.791 mm beyond the carrier left edge u=−50, with no shell contact. Encoder-right child x=42.386: 20 mm reaches u=64.886, or 9.886 mm beyond right edge u=55, with no modeled shell contact; a 25 mm probe reaches u=69.886 and intersects the right frame by 2.2667 mm³, placing this line's first shell contact between those two lengths. Shell-only, zero-tolerance centerline bound; not a 10–15 mm loop or plug pass. Real connector faces, width, cable bend, main-board bodies, retention and withdrawal require the separately sourced cable geometry and a new swept-volume check; shorter lead or qualified right-angle connector remain bounded alternatives, not selected.
Reproducible placed-fit record and preservation wording
Archive: complete measured scene snapshot, exact-distance/front/QT driver, exact results, individual encoder/panel result, QT probes, and evidence hashes. Run driver as Python with build123d in a folder containing the snapshot named scene.json; it fetches scene-key assets, then creates the three replayed JSONs. The original screening driver and results remain linked below. Replayed roof 14.1218 mm and J9 28.9903 mm reproduce the prior results, as does the 0.0008095 mm³ encoder/panel individual common volume. Scene and results cover only the modeled sources and common transforms, not later project changes or a physical assembly.
Copper preservation correction: integration commit paths show no main-board copper or placement edits; this is not a byte-for-byte historical-to-current net/trace proof, because expanded or computed layout representations can differ. This follow-up changed documents and archived evidence only; no routing, control movement, shell cut or main-board mutation. Heater DO NOT ENERGIZE, and upstream harness HOLD remains.
2026-11-12 approved appearance and partial carrier integration
The user approved the 42 × 30 mm bezel, 30 × 22 mm opening, and the preserved OLED and encoder centers. This supersedes the earlier appearance-approval hold below; it is not a manufacturing, fit or heater-safety approval. The approved bezel is not yet a physical enclosure model or cut.
The separately linked control-panel carrier project now has a native 105 × 42 mm, two-layer placement and schematic, unrouted. Handoff checks report ERC 0/0, DRC 12 airwires and two QT socket outside-board flags, and no overlapping copper; these do not establish fabrication readiness. The prior migration checklist is historical where it says the child does not yet exist.
The parent now includes
3D Model
as a model node only. Source and omissions audit, assembly script, and component checks identify the reconstruction, not a complete populated native export. That historical v1 had 115 solids and 25 nominal surface package bodies; the current v2 adds eight representations as described in the current reconciliation above. Cable/plug mating, fasteners and the installed knob remain absent. Source STEP bounds X=10…115, Y=−52…−10, Z=−7.285…29.5986 mm. At unit scale, its transform in the panel frame is P=O+(X−60)X̂+(Y+31)V+(Z−16.0986)N, O=(0,−57.5,61.5) mm, V=(0,cosθ,sinθ), N=(0,−sinθ,cosθ), θ=67.13549°. Parent node position is (−60,−30.621176,83.809051) mm and X rotation 67.13549°. No candidate carrier/module placeholder nodes were found to disable; earlier proxy views are historical.
Nominal CAD datums: display glass center (u,v)=(−25,0), encoder (35,0), so both are centered on their intended openings; OLED PCB center (−25,−1.428). The 30 × 22 window has nominal per-side surplus approximately 1.65 mm in u and 1.37 mm in v over the 26.7 × 19.26 mm glass outline. Existing panel Ø7 is line-to-line with nominal M7; the proposed Ø7.4 cut is not made or qualified. The native carrier core is 1.4986 mm, core plus two copper layers 1.5686 mm, and with two nominal masks 1.6186 mm versus the 1.6 mm target: finished thickness and tolerances require fabricator confirmation. Carrier module holes are nominal Ø2.9 mm while module holes are Ø2.5 mm; an M2.5 screw is nominally line-to-line in the latter, not a demonstrated fit.
Partial static fit — placed scene, nominal geometry only
Computed using the placed scene transforms and the imported STEP, not a bare-board surrogate. The scene contributes a common ~0.68468 mm Z offset to the enclosure and the board-parented model; their relative pose is preserved. The geometry is nominal, with no manufacturing tolerance or required cable/service clearance applied. Screening results, selected exact distances, front individual-body result and check source. Axis-aligned bounding-box separations are conservative lower bounds, not exact minimum distances. These results include only models that exist in the placed scene.
Table
Compared to partial carrier assembly
Nominal result
Disposition
Front panel vs simplified encoder
Minimum 0 mm; individual-body common volume 0.000810 mm³
Interference/contact, not a clearance pass. The whole-compound Boolean returned zero volume, but the individual encoder Boolean found the small overlap. It may be sensitive to rounded scene transforms and the nominal M7/Ø7 line-to-line condition; no positive clearance is established. Confirm actual bushing, hole and tolerances before selecting the separately proposed Ø7.4 opening.
Existing body models only, no mating plugs or wires.
Other available parent components and shell models
68 component model nodes and 11 shell models screened; all apart from front panel have positive bounding-box lower bounds, smallest 12.0 mm (right frame), or 28.8948 mm among included component bodies
Bounds do not qualify missing models, tolerances or service. The minimum across included components is not a loaded-assembly clearance.
QT plug loops, XH plugs, wires, fasteners, knob/press motion and the eight later-added surface representations
Unmeasured in this v1 scene
The eight representations are present in v2 but not included in this historical fit test. Actual cable shapes, mating poses and swept paths absent; no claim of serviceability.
The stored source has no complete plug or cable geometry; the outward module QT paths cannot yet be qualified. No reroute or center move has been made. A bounded alternative, if actual plug envelopes obstruct the loop, is an appropriately qualified short local lead or right-angle interface using the same approved centers; it remains a proposal until real mating and bend geometry is available.
Master two-board reconciliation — open unless marked done
Done: separate child board created, unrouted, and versioned partial mechanical reference placed in parent; integration commit paths show no main-board copper or placement edits. Byte-for-byte historical-to-current copper equality has not been established.
Open: represent off-board display/encoder and carrier interfaces accurately in the parent schematic; no actual off-board module symbol was added here. Reconcile both schematics, revisions, UI functions and single-count BOM including modules, encoder, knob, harness and mounting hardware.
Open: verify keyed physical cavity orientation, continuity and polarity of main J9 1=3V3, 2=GND, 3=SDA, 4=SCL against the child interface and selected SH cabling; verify total I²C pull-ups, voltage, timing and 3V3 power budget. J7/J8 remain reserved for optics.
Open: finish routing and run both boards' ERC/DRC; reconcile footprints and the two outside-board QT socket flags without moving approved centers. Qualify the 10–15 mm outward cable loops with real plug and bend geometry; a cable service/clearance pass is not established.
Open: qualify purchased display revision, glass datum, actual population and heights, encoder nut/washer, knob bore depth and installed height/engagement, fastener/insulation, plug mating and cable bend/service sweeps; revise the partial assembly against measured parts and freeze model revisions.
Open: reconcile the board, enclosure, power budget, firmware and harness records, then verify versioned manufacturing and assembly exports and perform physical first-article tests. HEATER DO NOT ENERGIZE; guarded insertion, thermal cutoff and upstream harness safety gates remain in force.
Historical 2026-11-11 focused follow-up — superseded by 2026-11-12 integration above
Current status: visible-arrangement review; mechanical/electrical release remains HOLD. The geometry-bound views below supersede the previous clipped orthographic attempt and the earlier carrier n=−5.5 trial. This is not a new PCB project, detailed shell repair, populated-board export or manufacturing instruction. No main-board copper, placement, schematic, or project layout object was changed. If the bezel/control appearance is accepted, proceed only to the previously requested linked-carrier workflow; first-article fit, cable service and bus qualification remain separate gates.
Corrected front concept — CAD-derived proxies, not fit-qualified
Corrected internal cutaway — parts hidden and carrier translucent for visibility
Bezel render correction: exterior remains u=−46…−4, v=−15…+15 mm (42×30 mm); the opening now spans u=−40…−10, v=−11…+11 mm (30×22 mm). Its center and the control positions are unchanged. The earlier images inadvertently showed a 32 mm wide window.
The corrected images preserve the previous rendering and framing, with captions in a separate footer; the front retains the approved flat-panel/translucent shell direction, and the internal view hides rear, roof, chamber, hatch and base for visibility. The dark green main PCB is an outline only, not populated electronics. The shell uses existing native STEP-derived mesh including the cycle-4 base; the added boards use nominal manufacturer CAD outlines with simplified glass, encoder, bezel, fasteners and XH blocks. The internal carrier is made translucent only for viewing; the actual board is not transparent. Carrier/module holes, plug shape, leads, nuts, wiring and finished internal assembly are not faithfully modeled. These are CAD-derived concept images, not product photos, an actual installed assembly, a completed carrier or physical-fit proof. The shaft/knob are cylindrical visual proxies; no D-shaft bore or retention is shown. The rendered white knob follows the 450-BA761 drawing, while the actual 377 kit appearance must be checked. This appearance proposal is limited to the bezel and control arrangement; it does not release the design for heating, manufacture or PCB routing.
Selected OLED and mounting datum
Use the purchasable Adafruit 326 STEMMA QT version as the single nominal reference, with the matching Adafruit 0.96in 128x64 OLED STEMMA QT.brd. Adafruit says the QT/auto-reset revision was introduced in 2020 and the 2024 update changes silkscreen only. CAD polygon outer bounds are 29.21×31.75 mm, hole centers X=(2.54,26.67), Y=(2.54,29.21), giving 24.13×26.67 mm. The catalog's 29.2×26.7 mm listing does not agree with the full CAD outline; use the explicitly identified CAD for the concept, not a mixture of dimensions. Exclude the repository's older 38×28.5 mm v2 and legacy 35.56×33.02 mm boards from this reference. Confirm that actual procured stock matches this revision before drilling.
In the selected Eagle CAD, the glass-outline footprint is centered 1.428 mm above the PCB outline center in its long-axis direction. Align that glass center to the panel's (u,v)=(−25,0), placing the module PCB center at (−25,−1.428). The resulting four nominal hole locations are u=−37.065/−12.935, v=−14.763/+11.907. The CAD glass-outline rectangle is about 26.703×19.26 mm and the indicated active-area rectangle is about 21.744×10.864 mm with center v≈+2.098. These are CAD interpretation, not physical metrology: verify glass/window datum, overall thickness and drilled holes on the purchased display. The proposed 30×22 mm bezel window nominally clears that assumed glass rectangle by about 1.65 mm horizontally and 1.37 mm vertically per side. The existing 36×24 mm opening remains unchanged; the proposed exterior bezel remains 42×30 mm. Attachment of this bezel is still unsolved.
Revised carrier/module and encoder stack
With the existing panel at n=−1.5…+1.5, use a trial carrier 105×42×1.6 mm with front face n=−14.6 and back face n=−16.2. Carrier center u=+2.5,v=0 has front-face world position approximately (2.5,−44.05,55.83) mm, with θ=67.13549°. This is a proposed placeholder, not a new board. Four candidate panel-carrier mounts remain (−46,±17),(+51,±17) with Ø3.2 carrier clearances; proposed stand-offs span n=−14.6…−1.5 (13.1 mm) and need actual bosses, screw engagement, isolation and strength design. Their visible mount details are not resolved.
Both module PCB front faces are trial n=−8.0 and backs n=−9.6, giving 5.0 mm to the carrier front. Candidate four independent Ø4 mm standoff envelopes per module, nominally M2.5 attachment, occupy this gap. For the 4991 reference PCB, encoder center remains (+35,0); nominal module holes are (24.84/45.16, ±10.16), PCB 25.4×25.4 mm and encoder footprint rotated 45°. The spacer envelopes in the image are proposals only; actual hole diameter, metal isolation and component clearance are not established. The encoder is soldered to the separate 4991 and panel-mounted by its own bushing so its push load should reach the panel, not the OLED; do not force an incompatible rigid stack into alignment.
The exact Adafruit-linked Bourns PEC11 drawing gives for the 15 mm shaft version L1=15 mm, LB=5 mm, l=7 mm, M7×0.75, and a 12.5×13.2 mm body face. Push travel is 0.5±0.2 mm. The drawing shows a nominal 6.5 mm from the PCB mounting plane to the bushing shoulder, which motivates n=−8.0 at the 3 mm panel's inside face n=−1.5; exact physical assembly face and solder seating must still be measured. Five millimeters of thread through a 3 mm panel nominally leaves 2 mm before washer and nut; thread and panel tolerances, nut/washer dimensions and usable engagement remain unknown. The existing panel's nominal Ø7 hole has zero nominal radial clearance to an M7 major diameter. A proposed Ø7.4 mm panel hole gives 0.2 mm nominal radial relief, but manufacturing tolerance and retained wall strength are not qualified. This is a proposed hidden cutout change, not a cut made in this pass.
The 450-BA761 drawing lists a white 6 mm D-shaft knob. It specifies Ø16 mm base and 14.5 mm overall height. Axial bore depth and engaged length remain unconfirmed: 4.5 mm in the bore view is a D-flat measurement, not evidence of 4.5 mm bore depth. The displayed knob is a simplified cylinder with its base at n=+4.5; a notional 3.0 mm panel-to-skirt gap minus maximum 0.7 mm push gives 2.3 mm nominal gap to the panel, but does not establish clearance to the nut, actual bore fit, shaft engagement or tolerance. Fit with the actual encoder and knob before hardware release.
Interboard connector and service concept
Candidate rear carrier connector is a top-entry B4B-XH-A with mating XHP-4 housing, approximately centered at (u,v)=(+5,−14), mounted on the carrier rear with the row parallel to +u and cable mating along −n toward the enclosure interior. Logical carrier pin order in increasing u is 1=3V3, 2=GND, 3=SDA, 4=SCL; confirm exact solder-side footprint orientation, cavity numbering and header body offset before fabrication. Both ends use keyed XHP-4/SXH contacts, end-to-end function map 1→1 etc. The JST XH drawing supports a 12.3 mm XHP-4 width, 5.75 mm assembly layout depth, 9.8 mm assembled height and 1.6 mm board thickness. The rectangle in the image uses these as an intentionally simplified 12.3×5.75×9.8 mm mated bounding proxy, not precise latch, body, terminal or pin geometry. Short, secured QT interfaces or direct qualified carrier connections to the two modules still require definitive connector selection, mounting and pin-map design; no loose branching is assumed. Exact local plug/latch/finger and bend-radius volumes remain absent.
A trial 10 mm straight withdrawal along −n, measured as an extrusion of the XH proxy, is merely a screening scenario, not the manufacturer-specified extraction travel. It clears the checked shell solids in the nominal proxy model, but its lowest z=31.963 mm leaves only 1.963 mm above the prior estimated z=30 mm main-board population envelope; actual populated parts, solder, wire, latch fingers and tool access were not modeled. Do not claim serviceable extraction on that basis. Whole rear removal and actual cable slack/bend/clamp remain not checked.
Geometry evidence and limits
Boolean fit report, fit script, and render script record the reconstruction; sources and positions are described above. Tested four proxies: carrier slab, display PCB bounding slab, encoder PCB bounding slab, and XH mated bounding block, against the existing native STEP base, UI, rear, roof, chamber, side frames, front strip and sides. All reported intersections are 0 mm³ for those proxy/shell pairs. Carrier-to-UI distance is 13.1 mm, carrier-to-roof 14.1218 mm, carrier-to-right frame 12.0154 mm, carrier-to-chamber 31.9133 mm. Carrier-to-each module slab is 5.0 mm. These do not include screws, OLED glass, encoder body/bushing, knob, carrier attachment bosses or actual fully populated PCB bodies and are not clearance verification for those objects. The XH block intentionally touches the rear carrier face.
The carrier slab spans z=35.8555…75.1771 mm; the mated XH proxy's lowest z is 35.8485 mm. Against an assumed main-board top population envelope of z≤30 mm these leave only 5.8555 mm and 5.8485 mm respectively, not counting actual population or tolerance. The 10 mm trial withdrawal proxy's 1.963 mm figure above is the more restrictive bound. No tolerance budget or as-built pass is claimed; no populated-board, cable, screw or thermal collision model has been run.
The original follow-up below is retained as a historical baseline, including the previously failed orthographic preview and earlier face n=−5.5 values; where it conflicts, this dated section controls. Its future multi-board migration checklist remains applicable. Firmware/pull-up/current, OLED physical revision, nut and bore engagement, module mounting loads and rear-service gates remain open. The mandatory one-shot cutoff and do-not-energize heater status remain unchanged.
Historical status and approval boundary
PRELIMINARY / NOT FIT-QUALIFIED. This is a dimensioned proposal for the approved flat-panel v2c, not a fabricated PCB or approved shell change. It preserves the existing OLED and encoder centerlines. No new board project, shell repair, wiring, routing, main-board copper or component placement has been created or altered. The separate carrier replaces the previously proposed loose UI branching harness; J7/J8 remain reserved for optics. Heater/chamber design is outside this work and the heater remains DO NOT ENERGIZE.
Orthographic projection draft: positions are drawn from the source panel and a proposed carrier envelope, with conceptual boxes, not installed module solids. It is not an approved 3D view; the footer overlaps an axis label and image edge checking reported cut-off. The part geometry is readable, but the image is not adequate to approve appearance or physical fit. Do not treat it as a populated collision or wiring view. No geometry-bound 3D front/rear assembly was verified in this pass.
Decision checkpoint: seek approval of the visible bezel and preserved control placement after a clean geometry-bound 3D front/internal preview and the dimensional gates below. Until then no daughterboard project or detailed shell repair. Proposed solution is not permission to manufacture.
Historical source datum and earlier proposed floorplan
The
3D Model
defines a 154 mm wide panel, length √(83²+35²)−0.6 = 89.477 mm, 3 mm thick, center O=(0,−57.5,61.5) in the main-board frame. Its X rotation θ=atan2(83,35)=67.13549°. Define local u along world +X; v uphill along (0,cosθ,sinθ); n outward along (0,−sinθ,cosθ). A local point is O+u·X+v·V+n·N. The panel center plane is n=0; inside face n=−1.5. X/Y/Z here are millimetres, board top z=0. Panel openings are explicitly provisional.
Table
Item
Proposed / sourced nominal
Status
Carrier
Rectangle u=−50…+55, v=−21…+21: 105×42 mm, two copper layers, target 1.6 mm board; no routing yet.
Planning envelope, tolerance/material TBD.
Carrier pose
Front face n=−5.5; rear n=−7.1. Board-front center u=+2.5,v=0 => approximately (2.5,−52.43,59.36) mm; local X rotation 67.13549°.
Planning only; 4.0 mm front-face gap behind panel's inside face is a trial stack, not demonstrated assembly clearance.
Carrier mounting
Four candidate Ø3.2 clearance holes at (u,v)=(-46,±17),(+51,±17); four independent M3 screws and spacers/bosses, not OLED solder. Head, spacer length, enclosure attachment, isolation and loaded push/creep strength TBD.
Proposed geometry, not holes in shell or PCB; M3 availability/stack must be qualified.
Existing display opening
Center (−25,0), 36×24 mm in panel source.
Unchanged; unqualified for display retention.
Proposed display surround
Center (−25,0): 42×30 mm exterior bezel with 30×22 mm clear window. Nominal coverage extends 3 mm beyond existing opening each side.
Visible new bezel for approval; not final window, thickness, material, attachment or glass clearance.
OLED
Display center targeted (−25,0); orientation landscape. Temporary 38×32 mm bounding proxy, not a real module or verified glass center.
Envelope only; module stack, physical display center and connector side are unresolved.
Encoder
Center (+35,0), current panel hole Ø7; Adafruit 4991 PCB intended parallel to panel and encoder shaft normal to panel.
Hole and assembly unqualified, do not drill.
Encoder 4991 pattern
Its manufacturer Eagle board measures 25.4×25.4 mm at board outline; encoder footprint center (12.7,12.7), four 2.5 mm mounting-hole elements at (2.54/22.86,2.54/22.86), i.e. 20.32×20.32 mm nominal center spacing, and a 45° encoder footprint. If axes align with panel, hole centers are (24.84/45.16, ±10.16).
CAD revision evidence; hole drill, exact purchased board and screw/standoff stack need verification. Product page lists 25.6×25.3×4.6 mm overall.
Interboard connector zone
Candidate J-UI center (u=+5,v=−14), on carrier rear, latch and cable facing inward approximately −n, away from the face, then routed towards J9.
Zone only, not a finalized footprint, rotation, mating-direction claim or extraction clearance.
OLED revision conflict — do not freeze mounting
Adafruit 326 product page lists PCB 29.2×26.7 mm, screen 26.6×19 mm, 24 mm mounting spacing, and includes QT connectors. However the manufacturer's pinned Eagle source repository contains multiple revisions: the STEMMA QT board outline is 29.21×31.75 mm with nominal hole centers (2.54/26.67, 2.54/29.21), i.e. 24.13×26.67 mm spacing; a different v2 board outline is 38×28.5 mm with 32×22.5 mm hole spacing. This is evidence of different candidate files, not proof of the shipped revision. The 38×32 proxy encompasses those unrotated board outlines but excludes a real glass datum, connectors, fastening heads and leads. Determine the shipped revision and exact visible screen offset from physical samples/CAD before selecting or drilling carrier mount holes. Under the catalog dimensions only, a centered screen inside the proposed 30×22 window would have 1.7 mm horizontal and 1.5 mm vertical nominal excess per side; this assumes screen-centered geometry and does not prove visible pixel clearance.
Historical mechanical concept and unresolved stack
Use independent carrier supports into panel/frame to carry carrier mass and service loads. The encoder bushing/nut should clamp the actual panel or a rigid independent bracket: knob press → shaft/bushing → panel/bracket, not through OLED glass, OLED solder or a fragile bus connection. The 4991 breakout is a separate module rigidly supported at its own mounting holes, with compliant connection/spacing as required to avoid forcing its body or pins; never assume the bushing fixes the breakout-to-carrier spacing. OLED should attach via its verified mounting holes and insulating spacers, with its glass free of clamping stress. Assembly can require inserts/bosses on the interior and may involve visible screw heads; specific attachment depends on actual hole access. No fixed locations for OLED mounting or panel boss drill have been released.
Adafruit 377 links PEC11-4215F-S24 encoder and 450-BA761 knob; the manufacturer identifies this as a compatible encoder option for 4991. An initial web extraction of the Bourns drawing suggests 15 mm shaft, 7 mm bushing, 5 mm bushing length, M7×0.75 and 0.5 mm travel, but immutable drawing evidence remains pending/unverified. Treat these only as questions to verify against the exact shipped hardware. In particular, do not assume the Ø7 panel hole accepts the thread with tolerance or that the 5 mm threaded length gives sufficient full nut engagement through 3 mm PETG plus washer. Measure body shoulder→panel inside, protruding thread, washer/nut stack, shaft flat/engagement depth, nut outside diameter, knob bottom and skirt, axial endplay, full push travel including tolerances and positive clearance at travel limit; obtain knob drawing and test actual parts. The panel-to-carrier 4 mm trial gap cannot be certified until that stack and module PCB orientation are known.
Electrical interface and candidates
Live native net inspection confirms main J9 B4B-XH-A 1=3V3, 2=GND, 3=I2C_SDA, 4=I2C_SCL. U1 GP4/GP5 and U2 SDA/SCL also share these nets; J7 remains optical. R3/R4 are each 4.7 kΩ to 3V3. Recommended candidate carrier connector is a matching keyed 4-pin JST XH header and a harness with XHP-4 housing and appropriate SXH-001T-P0.6 contacts at both board ends; it is not installed. Map by function 1→1,2→2,3→3,4→4 only after checking the actual header and mating-housing numbered cavity views, then perform end-to-end continuity, short and polarity checks. Do not infer wiring from wire colors. Nominal 28–22 AWG range for this contact was previously documented in Harness Fit Review; actual wire OD, crimp tooling, length, bend and strain relief remain undecided.
Use the carrier as the local I²C distribution node. Source-confirm module signals and choose either properly secured short module interfaces or verified local module mating connectors; do not use OLED solder/glass or loose branch splices for strain relief. 326 operates from 3 V logic and defaults to I²C; reported address 0x3C or 0x3D. 4991 accepts 3–5 V power/logic, defaults to 0x36, and includes an unsoldered encoder interface and NeoPixel. The 4991 pinout guide specifies 10 kΩ pull-up on each SDA and SCL pin; verify the actual rail and all physical revisions before installation. Even assuming only one 10 kΩ resistor on each line in parallel with 4.7 kΩ on the main board, equivalent is 3.20 kΩ per line, before OLED, U2 or optical-module pull-ups. Total equivalent, sink current, rise time, bus cable capacitance and worst-case 3V3 current/rail headroom including display/NeoPixel are not established. Confirm module reset, firmware seesaw input, encoder direction, and bus address collision with U2/optical before release. Neither plausible address separation nor nominal voltage proves system compatibility.
Historical fit screen — superseded by the current geometry evidence above
Table
Comparison
Nominal result / assumptions
Status
Carrier vs panel side edges
u board −50…55 vs panel −77…77 gives 27 mm left and 22 mm right; v carrier ±21 vs panel ±44.739 gives 23.739 mm each end.
Plane outline arithmetic, no hardware.
Existing OLED hole vs listed 29.2×26.7 PCB
If centered, horizontal overhang is −3.4 mm/side; hole alone cannot retain or cover it.
NOT VERIFIED: exact connector geometry, length, clamp, tolerances and swept poses absent. Rear-panel service needs no service extension and must not pull on carrier.
Panel source includes fastener seats, and actual roof, frame, base, main-board bodies, standoffs, OLED glass, encoder rear body, connector plugs and cable sweeps have not been intersected with this slab. No overlap-volume or tolerance-qualified fit pass is claimed. Following detailed design, import real populated carrier and qualified mated models and check installed state, both plug extraction vectors, finger/tool clearances, cable bend and clamp volumes, and whole-rear removal with supported cable, then the existing base+PCB vertical lowering sequence. The footprint target and these arithmetic clearances are not evidence of safe fit.
Future migration and reconciliation checklist — AFTER arrangement approval
Create a separately linked carrier project: its own two-layer schematic, stackup, placement and fabrication outputs are easier to review and version without disturbing the 100×100 mm four-layer main board; link it from this parent and preserve cross-project assembly references. Do not create it yet.
Record main J9 and carrier connector pin-by-pin mapping and physical cavity orientation, keyed harness specification, continuity checks, cable/strain-relief/service schedule; cross-check shared nets and GP4/GP5, plus J7/J8 reserved functions.
Build the carrier schematic with module electrical interfaces, input connector and actual wiring strategy, no duplicate pull-ups without system budget; check module address conflicts, pull-up rails, power/startup/firmware. Represent preassembled OLED and encoder module once in the appropriate BOM, rather than duplicating internal parts or counting them again in the parent; include encoder, knob, fasteners, cables and purchased contacts once in an assembly BOM.
Preserve parent main-board placements, layers and copper unless separately authorized; reconcile parent schematic symbols/connectivity and cross-board interface documentation only when settled. Route the carrier only after mounting, electrical and fit gates close. Run ERC/DRC independently on both boards plus explicit interboard net/polarity and 3V3 power checks.
Export the carrier as a versioned populated 3D assembly, including measured module and connector solids; fit it back in the parent at the documented transform and perform actual collision, assembly, cable, fastener/tool and service-path checks. Update proposed bezel and fastening details only after visible approval; no new enclosure geometry in this pass.
Reconcile the parent project specification, harness fit review, enclosure design record, power budget, firmware and bring-up/test plan with both boards, revisions and mating information. Keep the research-use-only single-tube and guarded-hot-insertion architecture. Preserve the mandatory G4A00091C cutoff and independent thermal/optical gates.
On release produce separate board fabrication/assembly exports, BOMs and pick-and-place as applicable, plus master harness/assembly BOM and drawings; verify every export and assembly revision against both project sources and run physical electrical and mechanical first-article tests.
Open gates
Required before approving a board manufacturing plan: exact OLED revision and glass center, 4991 and encoder orientation/drawings, module-to-carrier stack and supports, bushing/panel/nut/knob full press-travel fit, cable connector bodies/contact mapping, module current/pull-ups and bus timing, shell bosses, and populated static/service sweeps. Clean geometry-bound concept views are now provided above, but populated 3D assembly and physical validation remain outstanding. If purchased hardware differs, update the proposal and request the visible-layout decision rather than silently moving the controls. This is not a heater, routing or overall instrument release.