Hardware Prototype Timeline


flux

The clamp hardware is now modeled without drilling the block or changing the supports. But I can’t call the restraints complete: the lead paths still need local bends into the clamps, and no wire-contact liner or safe grip size is established. I’m checking the added hardware and preservation claims, then I’ll stop this pass with those limits clearly stated.
"Wire Restraint Verification" completed.
"Wire Restraint CAD Fix" completed.
"Wire Restraint CAD Fix" completed.

flux

The screw-operated clamp hardware is modeled, but actual wire retention is not yet established.
I added a clamp assembly around the existing rear support, with separate heater, sensor and cutoff jaws. The latest repair:
  • Routes three planning lanes through the jaws without the earlier hardware collisions.
  • Moves the collar screw clear of the stand by 2 mm.
  • Preserves the electronics, completed supports, panels and current board poses.
These are closing clamp mechanisms, unlike the earlier open guides. However, no wire-contact liner or compatible grip dimensions are established. Heater-lead diameter, allowable compression, bend limits and safe first-support distance remain unresolved. The heater’s first strain relief cannot yet be called complete.
The final repair has reported geometry checks, but I could not independently recheck it before execution stopped. Copper Clearance remained ignored. Nothing is approved for fabrication or heating.
I saved the remaining work and evidence in Wire Restraint Continuation.
Execution stopped because your account ran out of ACUs.

Waiting for input


Last modified 4d ago

Control Panel Mechanical Preparation
Final finite cable-only repair — implemented
Current revision: local clearance repair report,

3D Model

,

3D Model

. These supersede earlier cable asset links; prior positive review findings are retained.
The failed3.9/3.6mm-radius paths below are superseded by installed200mm bows with minimum radii15.494/15.463mm. Separate left/right paths and two physically attached loose guides now exist; no connector/module/control-center changes. Guides reuse the lower carrier M3×6 bolts and replace two1mm washers without changing thread engagement. Two custom carrier washers remain, plus all16 module washers. No added standard hardware, shell cuts, child or copper edits.
Final local195mm OLED reshape repairs the independently measured0.371317mm exact support gap to 1.198464mm, exceeding1mm target without removing support material or changing the20N-assumed load path.195/200/205mm exact support gaps1.198464/1.011228/1.238573mm and radii15.298166/15.494188/15.199198mm all pass the local targets. The earlier0.05368mm was a conservative mesh bound and is superseded. Endpoints, guide centers, hardware and installed nominal200mm geometry remain unchanged. Exact mating-envelope allowance is zero/negative under tolerance; true keyed seating, supplier cable OD/bend/fatigue, printed strength/fit, prior housing-contact and knob-bore holds remain. This is nominal cable/retention completion, not overall instrument readiness.
Current report/source links ·

3D Model

· Installed scene. No manufacturing/heater release.
2026-11-12 anchored-support follow-up — retained, cable statements superseded
This section supersedes the axial geometry and hardware in the earlier partial repair below. No manufacture, electrical, heater or press-load release. Main copper and child data unchanged; control centers and exterior panel openings unchanged.
  • Installed two one-solid bolted support rails. Hidden frame insert pilots at u=±67,v=±24,n=-8.2, Ø3.99×4.56mm; each native frame removes114.03299mm³. Added four frame and four carrier M3×6 bolts, eight SPIROL29 short M3 inserts, and four1mm custom insulating washers. Engagement3.0mm frame/3.3814mm carrier. Old floating cradle disabled.
  • Carrier finished faces n=-22.6/-24.2186mm; core faces -22.66/-24.1586. Encoder front/rear -16/-17.6, four5mm nylon spacers. OLED independently advanced to front/rear -6/-7.6, four15mm nylon spacers. Eight through-bolts replace all opposing screws: fourM2×12 encoder/fourM2×25 OLED, eightM2 nuts, sixteen nylon washers. Nut engagement1.6mm; tails1.1814/4.1814mm. No near-touching opposing tips remain.
  • Installed relieved insulating encoder PCB backstop beneath housing. Assumed design press load20N, not strength certified. Nominal load path reaches the frame independently of OLED solder; it depends on the real encoder housing seating flush on its PCB. It is not a direct bare-housing clamp. Actual housing seating, push force/stroke, knob bore/set-screw engagement remain source/physical qualification holds.
  • OLED entire-glass aperture half-cone9.51° with nominal1.45mm glass; conservative zero-projection bound8.10°. This is geometric visibility, not contrast or active-pixel viewing qualification. Adafruit326 lists6.2mm overall, not separate glass thickness. Screen carries no bezel load.
  • Checks:87 targeted fixture/hardware comparisons;24 staged extraction/plug-withdrawal checks. Installed scene read-back confirms unit scale and direct tilted transforms. Some broad/compound exact checks timed out; full all-pairs validation is not claimed.
  • Still incomplete: cable clips/retention were not designed. Installed200mm/Ø4mm cable reservations are not released harness geometry: bend minima3.91/3.56mm miss the proposed15mm target, and source OD/minimum bend/SH seating datum remain unresolved. No renewed module/knob approval is requested.
Current source and evidence
Earlier sections below are historical and must not drive current fabrication.
2026-11-12 selected-set installed candidate — partial repair, current
PARTIAL, NOT FIT/LOAD/MANUFACTURING RELEASE. The selected set is now represented at an installed nominal pose in the parent, rather than only uninstalled references. New group Selected controls has 30 separate model nodes: current carrier/module reconstruction, selected 5880 envelope, black 5527 exterior, bezel, adhesive ring, cradle, eight spacers and sixteen screws. The old control carrier v2 is retained with active=false, independently read back. Main PCB placement/copper, child board and shell cuts were untouched. No purchase/routing/heater release.
Current source and evidence
Implemented nominal stack
Panel O=(0,-57.5,61.5) mm, thetaX=67.1354918781°. Carrier core front n=-22.6, core rear -24.0986; source-current native core remains 1.4986 mm, not silently changed to a 1.6 mm fabricated board. Nominal module front/rear -16/-17.6 gives 5 mm core-face gap, 8 mm farther inward than historical carrier pose. Native front finish allowance 0.06 mm makes the nominal finished-face gap 4.94 mm; exact spacer seating still needs reconciliation. Display glass and encoder centers remain u=-25/+35,v=0. Both module boards now share this axial pose; glass is consequently deeply recessed (front n=-14.55); off-axis readability is not verified.
5880 nominal body 11.7×12×6.5, shoulder n=-9.5, bushing end -2.5 and shaft tip +10.5 follow the linked EC11 drawing with flush PCB seating assumption. Only Ø6 shaft enters the unchanged Ø7 panel opening. Bushing setback is 1 mm. Black 5527 catalog exterior Ø20×12.5 has candidate base n=+3.5, giving 2 mm panel separation. No invented bore/set-screw geometry; 197.920337 mm³ shaft/exterior-envelope overlap is intentional occupied reservation, not verified engagement. Linked 5527 drawing/catalog discrepancy remains a feature-specific hold.
Bezel 42×30/window30×22 is now placed, 2 mm engineering thickness, rear face n=1.63. Separate nominal 0.13 mm 3M9472LE ring bears only on panel land (396 mm²); adhesive strength/peel and PETG surface qualification remain open.
Real bounded hardware and incomplete load path
Eight nominal M2 threaded Ø4×5 mm spacers and sixteen M2×4 socket-head screws, head Ø3.8×2 are separately modeled at module holes. Sources: spacer vendor, ISO4762 screw supplier dimensions. These are proposal hardware, not purchases, a qualified BOM or detailed threads. Nominal opposing screw penetrations 2.4 and 2.5014 mm leave only 0.0986 mm between tips before finish/tolerance: not an acceptable unqualified production stack. Supplier thread depth, length tolerances, isolation and finished-face seating must be resolved. Nominal M2-to-module Ø2.5 radial slack 0.25 mm; carrier Ø2.9 slack 0.45 mm.
A real U-shaped cradle candidate has two 6×46×3 mm rails and a 103×6×3 mm lower rail, with four Ø3.2 holes matching carrier mounts. It is not a completed enclosure support: carrier/cradle bolts, frame anchorage, housing backstop and continuous encoder push-to-frame load path are still UNSOLVED engineering work. Do not confuse model placement with physical installation. PETG prototype assumption; fillets, printability, stiffness, creep and loaded deflection unqualified. Four encoder spacers are distinct from four OLED spacers, but the common carrier/frame load path remains incomplete.
Checks and tolerance budget
The completed replay screened 143 available parent model nodes with conservative bounding distances, excluding the disabled historical base/roof/rear and prior carrier. It found no missing cached input. Exact individual-to-panel results: encoder 0.5000 mm, knob 2.0000 mm, bezel 0.1300 mm, carrier 13.26346 mm, cradle 22.6586 mm, each 0 mm³ overlap; adhesive is intentional face contact, 0 mm³ common volume. Initial whole-parent exact run timed out before JSON completion; its archived completed log reports roof16.53135, left/right frame19.05448/14.76730, J9/J10 19.99089 and J8 20.31686 mm, all zero overlap. Those log results are not a completed all-pairs exact audit. Internal new-item checks find only the intentional knob-envelope/shaft overlap; inherited carrier/package self-overlaps and all hardware-to-population pairs were not fully qualified.
Read-back caught that a group ignored X tilt/Z; direct model transforms fixed this. Final rendered scene shows the intended inclined assembly and black knob, scale1, common scene Z offset +0.68468 mm. Scene-rounded angle introduces roughly sub-micron CAD transform differences, not a physical tolerance claim.
Physical margins remain symbolic: shaft radial margin = 0.5 minus combined size/location/runout errors; bushing setback margin = 1 minus stack/deflection; knob clearance = 2 minus actual switch stroke/stack/deflection. Unknown values are not zero. No press-travel, strength, service or manufactured-fit PASS.
Remaining finite scope
Unfinished: enclosure/frame attachment and full independent press-load path; complete 4424 plug/cable/clip/tool/service envelopes; populated hardware interference review; released tolerance stack and assembly BOM reconciliation. Actual stroke/force, knob bore/screw position, stock encoder seating and wire OD/bend capability block their dependent qualification. They do not invalidate the completed nominal placement. No new module/knob approval is requested. Child 8 intentional airwires and electrical rail/headroom/pull-up/rise-time holds remain; use 3V3 only. Heater DO NOT ENERGIZE.
Everything below is historical where it conflicts with this installed-candidate section.
2026-11-12 approved selected hardware — provisional only
The user approved Adafruit 326 OLED, 5880 presoldered encoder, 5527 black Ø20 × 12.5 mm set-screw knob, two 4424 PH-to-SH 200 mm leads, and rear carrier PH headers. Selected-set record has pin mapping and source references; its earlier knob-approval request is superseded by the user's approval. The visible 42 × 30 bezel / 30 × 22 window and glass (u,v)=(-25,0), encoder (+35,0) remain fixed. No main-board geometry, placement, copper or child project is changed by this preparation. Existing parent carrier v2 represents the old 4991/377 arrangement and omits installed cables; it remains displayed pending integration of the child's new source-current export. It is not an as-built 5880 assembly and must not be used as evidence of the selected set.
Encoder shaft datum and load path
5880 supplied drawing depicts a 6.5 mm housing depth from PCB-side plane to bushing shoulder, checked L=20, N=7 and L1=12.5, and shaft nominal Ø6−0.05. Drawing units/stock version and the exact solder seating must be confirmed: the drawing illustrates a splined shaft while the product page calls for D-shaft or set-screw knobs. Its 20/7/12.5 choices are documented by the extracted table. Selected knob has nominal 6 mm hole and set screw; exact bore depth, axial screw position and engagement remain unknown. Do not assume the fit from diameter alone.
In the existing panel local frame, face n=+1.5 and inside n=−1.5 mm. For an illustrative, not frozen, 1 mm bushing setback, the nominal bushing free end is n=−2.5, shoulder n≈−9.5, module component-side mounting plane n≈−16.0 and shaft end n≈+10.5: 9 mm nominal protrudes beyond the outer panel face. This arithmetic assumes N means axial shoulder-to-bushing-end and 6.5 means seating-to-shoulder; confirm those datums on the exact supplied module before using them. Existing nominal Ø7 panel opening minus nominal Ø6 shaft gives 0.5 mm radial slack before printed ovality, positioning, shaft runout, thermal movement and press deflection; this is not a tolerance-qualified fit. The Ø7 bushing must remain behind the panel; no nut, washer clamp, enlargement or shell cut is made. The 5527's actual skirt/shaft engagement and full push sweep are unverified.
Important integration consequence: the prior carrier front is n=−14.6 and its 1.4986 mm core extends to n=−16.0986; a 1.6 mm module seated at n≈−16.0 extends to n≈−17.6. Their axial intervals overlap by about 0.0986 mm before copper/mask, so the old carrier/module stack cannot be assumed usable for the selected arrangement. To have an illustrative 5.0 mm clear face gap between module rear (−17.6) and carrier front, the carrier front must be at n≈−22.6; this is an equation input for the new assembly, not an approved placement or collision result. Other stacks could be engineered, but exact source-current native board geometry, module face, mounting hardware and rear PH envelopes must be known before freezing one.
Mount by four separate module holes (nominal 20.32 × 20.32 mm pattern from pinned 4991-family CAD, not yet confirmed as shipped 5880), with independent carrier/panel support; keep all OLED glass, flex and solder joints out of the encoder push path. With PCB-only support, force passes through the encoder tabs/terminal joints and PCB into the four support contacts and then the carrier/panel; equal F/4 per support is only an ideal symmetric static assumption, not a qualification. A removable, separately fixed backstop bearing on the sourced encoder housing—not its contacts, glass or moving shaft—could reduce solder-joint loading; its shape and location cannot be fixed until the exported housing, other rear components and access are known. Do not install a rigid bracket without checking thermal clearances and switch overtravel. The supplied encoder specification contains shaft push/pull strength, not the switch operating force or stroke; the latter remain unverified. Require actual actuation force and maximum full travel, backstop gap, board/support deflection, fastener pull-out and repeated-press test before load release. The previously sourced 13 mm M3 standoffs are not a selected stack for the shifted carrier; M2.5 is only a candidate for nominal Ø2.5 module holes, with purchased screw, insulating washer and actual clearance unverified.
Decorative bezel candidate
A separate

3D Model

preserves 42 × 30 mm outside and 30 × 22 mm through-window, with a provisional 2 mm thickness. One solid, volume 1200 mm³, was validated by the asset pipeline. 2 mm is a design proposal, not the approved visible dimension or printable release; a prototype flat-on-bed PETG 0.4 mm nozzle is only a process assumption, with chamfer, finish, build volume, tolerances and glass clearance unverified. It was not placed into the native scene, and no support or attachment is represented as installed. For an illustrative 0.13 mm adhesive separation on the existing panel's outside face, the proposed mating face is n=+1.63. A 3M 9472LE candidate has nominal 0.13 mm thickness. In the archived panel model, the existing 36 × 24 aperture leaves 3 mm outer bonding land, nominal 396 mm²; bond coverage, corners, printing surface and glass contact require real testing. Use the panel, not OLED or encoder solder, for bezel support.
The shell-check results, driver and prior exact scene snapshot show 0.1300 mm panel-face separation with zero common volume, 21.5483 mm left-frame and 25.0928 mm roof minimum distances, zero common volume for each of seven named shell solids. These are saved-scene nominal checks only; the code expects downloaded scene STEP assets with the filenames described in the driver and must be rerun after any scene change. No tolerance, installed 5880, knob, glass, adhesive, shell screws or service sweep is included.
Rear loom reservation and assembly plan
4424 is a 200 mm PH-to-SH assembly; its actual insulation OD, bend minimum and length measurement convention are not published. SH catalog nominal assembly length 6.25 mm and height 2.95 mm, PH top-entry mating height 8 mm and nominal width 4.5 mm are connector guideline dimensions, not full plug/wire/retention tolerance models: SH catalog, JST PH catalog. Neither side is released as a service fit.
Reserve two independently secured, noncrossing service corridors on the rear side of the carrier: W1 wholly to the left, W2 wholly to the right; keep 10 mm straight at each housing where feasible, strain-relief at each branch, and away from encoder press travel, sharp edges, heater and thermal cutoff. A preliminary panel-projection allocation for later testing is two circles of 15 mm centerline radius centered at (u,v)=(-30,0) and (+35,0); their u extents are [-45,-15] and [20,50], so they are disjoint and fit the carrier outline u=[-50,55], v=[-21,21] in projection. This is reserved 2D space only, not evidence the actual connector endpoints can reach it or that the 3D shell, clips and cable sweep clear. A 180° centerline turn at 15 mm uses 47.12 mm; adding two 10 mm straight segments uses 67.12 mm, leaving at most 132.88 mm of a 200 mm nominal lead before connector-length conventions and all other segments. R≥15 mm is an engineering target, not a stated cable minimum. A real route can be rejected by header positions, available depth, cable stiffness, service slack or shell; do not cut clips or claim fit until the actual child placement and cable envelope are checked.
Provisional service sequence: power OFF; remove/open the supported enclosure panel while preventing cable tension; mount modules with SH leads attached, route each lead separately behind the carrier with broad bends and soft non-crushing strain relief; mount carrier and connect each keyed PH end; verify polarity and continuity before power; retain slack for reopening and do not pull on OLED, encoder or PCB solder. Exact clips, attachment, withdrawal/finger volumes and sequence remain to be verified on source-current assembly.
Required inputs from child export / release gates
  1. Exact selected 5880 PCB orientation, source-current populated STEP/GLB, PCB and housing/shaft datum, and authoritative STEP bounds/origin/transform; native child coordinate map and revision.
  2. As-placed rear PH J2/J3 footprint/pin-1 origins, 3D header orientation and center-to-mating-face offsets; installed 326 and 5880 SH port choice/pose, correct 4424 signal order, including plug envelopes or their separately sourced geometry.
  3. Carrier and module thicknesses, module holes and real fasteners; selected PH solder tails and all under-board bodies. Collision fit must include existing parent shell and main-board populated bodies, bead/adhesive stack and entire cable/service sweep.
  4. Exact 5880 measured shaft projection, actuator force/stroke and board seating; 5527 bore depth, set-screw height, engagement and installed knob clearance; test printed panel hole and support alignment. These limit their dependent release, not independent planning.
  5. Recheck all power, I²C rise-time, 200 mm cable drop and load; V+=3V3, never 5V; mate power-off. Parent off-board schematic representation, BOM and manufacturing reconciliation remain open. Heater DO NOT ENERGIZE, upstream harness HOLD; no PCB routing or printable release.
  • Final finite cable-only repair — implemented

  • 2026-11-12 anchored-support follow-up — retained, cable statements superseded

  • Current source and evidence

  • 2026-11-12 selected-set installed candidate — partial repair, current

  • Current source and evidence

  • Implemented nominal stack

  • Real bounded hardware and incomplete load path

  • Checks and tolerance budget

  • Remaining finite scope

  • 2026-11-12 approved selected hardware — provisional only

  • Encoder shaft datum and load path

  • Decorative bezel candidate

  • Rear loom reservation and assembly plan

  • Required inputs from child export / release gates