Schematic for Arduino Nano Shield Template 3Re8: cizgiizleyen.com ·...

Terminal
An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
natarius
Ground
A common return path for electric current. Commonly known as ground.
jharwinbarrozo
20.5M
Net Portal
A net identifier used to create connectivity to other Net Portal with the same designator. #portal
jharwinbarrozo
43.0M
Power Net Portal
Power net portal is a special schematic object used to define a power or ground net. Power ports allow you to conveniently indicate a power net at any location in the design. Power nets of the same designator automatically connect throughout your design #portal #power
jharwinbarrozo
11.4M
Generic Resistor
A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Capacitor
A generic fixed capacitor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Inductor
A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
jharwinbarrozo
14.2k
875105359001
10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
jharwinbarrozo
1.2M
CTL1206FYW1T
Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
jharwinbarrozo
1.1M
1070TR
Battery Holder (Open) Coin, 20.0mm 1 Cell SMD (SMT) Tab bate or batt #forLedBlink
jharwinbarrozo
700.5k

Capacitance

2 F

+3V3

SW1

+5V

Distributor	Qty 1
	Arrow	$1.13–$1.22
	Digi-Key	$2.27
	LCSC	$1.64
	Mouser	$1.46
	Verical	$0.83–$1.63

11 pin connector component

ekismet

11 pin connector component

5mo

auto place my components

ekismet

@copilot auto place my components

5mo

copilot

Sure, I can provide some suggestions on how you might place your components on your PCB. Since you’re working with an Arduino Nano shield template, we’ll focus on making connections logical and routes short.

Suggestions for Component Placement:

Arduino Nano Module: Place the Arduino Nano footprint centrally so that connections to all headers are balanced and easily accessible.

Headers (J1, J2, J3, J4, J5):
- Place $J1$ and $J2$ near the corresponding pinout of the Arduino Nano.
- $J4$ and $J5$ can be placed on either side of the Arduino Nano based on required connections.
- Ensure $J3$ is located where it provides easy access to the pins it connects to.

Interconnections:

Power Connections:
- Place the power distribution traces to connect +3V3 and +5V nets to the corresponding pins.
- Connect $J1:Pin_2$ to $+3V3:P1$
- Connect $J1:Pin_12$ to $+5V:P1$

Ground (GND):
- Ensure $J2:Pin_12$ and $J1:Pin_14$ connect to the ground plane or a common ground net.

Signal Nets:
- Make connections for the signals as specified, ensuring minimal trace length where possible to avoid interference.

Available Nets:

Net 4: Connect $J4:Pin_3$ to $J2:Pin_8$

Net 1: Connect $J2:Pin_9$ to $J3:Pin_1$

Net 8: Connect $J2:Pin_4$ to $J5:Pin_2$

Net 9: Connect $J2:Pin_3$ to $J5:Pin_1$

Net 5: Connect $J4:Pin_2$ to $J2:Pin_7$

Net 7: Connect $J5:Pin_3$ to $J2:Pin_5$

Net 3: Connect $J3:Pin_3$ to $J2:Pin_11$

Net 2: Connect $J2:Pin_10$ to $J3:Pin_2$

Net 6: Connect $J2:Pin_6$ to $J4:Pin_1$

These placements and connections should provide a starting point for layout. Let me know if you need further customization or have more components or requirements to consider!

5mo

TB6612FNG componenti laızm

ekismet

@copilot TB6612FNG componenti laızm

5mo

copilot

The

TB6612FNG

is a dual DC motor driver IC. It offers reliable control over two DC motors at voltages from 2.5V to 13.5V with a maximum current of 1.2A per channel (3.2A peak). Let's add it to your Arduino Nano Shield project and specify the key connections for you.

Important Pins on the

TB6612FNG

VCC: Power supply (typically 5V)

GND: Ground

AIN1, AIN2: Input control for Motor A

BIN1, BIN2: Input control for Motor B

PWMA: PWM signal input for Motor A speed control

PWMB: PWM signal input for Motor B speed control

AO1, AO2: Outputs for Motor A

BO1, BO2: Outputs for Motor B

STBY: Standby control

Sample Connections for Arduino Nano Shield:

Power Connections:
- Connect $TB6612FNG:VCC$ to $Arduino Nano:3V3$ (or 5V depending on your $TB6612FNG$ pin configuration).
- Connect $TB6612FNG:GND$ to $Arduino Nano:GND$ .

Motor Control Pins:
- Connect $TB6612FNG:AIN1$ to an Arduino digital pin of your choice (e.g., D2).
- Connect $TB6612FNG:AIN2$ to another Arduino digital pin (e.g., D3).
- Connect $TB6612FNG:BIN1$ to another Arduino digital pin (e.g., D4).
- Connect $TB6612FNG:BIN2$ to another Arduino digital pin (e.g., D5).
- Connect $TB6612FNG:PWMA$ to a PWM-capable Arduino pin (e.g., D6).
- Connect $TB6612FNG:PWMB$ to another PWM-capable Arduino pin (e.g., D9).

Standby Pin:
- Connect $TB6612FNG:STBY$ to an Arduino digital pin (e.g., D7).

Connect TB6612FNG:VCC to Arduino Nano:3V3.
Connect TB6612FNG:GND to Arduino Nano:GND.
Connect TB6612FNG:AIN1 to Arduino Nano:D2.
Connect TB6612FNG:AIN2 to Arduino Nano:D3.
Connect TB6612FNG:BIN1 to Arduino Nano:D4.
Connect TB6612FNG:BIN2 to Arduino Nano:D5.
Connect TB6612FNG:PWMA to Arduino Nano:D6.
Connect TB6612FNG:PWMB to Arduino Nano:D9.
Connect TB6612FNG:STBY to Arduino Nano:D7.

You can now add the

TB6612FNG

component to your project in Flux and complete the connections as mentioned above. Let me know if you need more details or further assistance!

5mo

Hi! I’m Copilot, I’m here to help you design your hardware projects. Ask me anyt...

copilot

Hi! I’m Copilot, I’m here to help you design your hardware projects. Ask me anything:

Starting a Project

@copilot can you partner up with me to design a pcb?

Exploring Architectures

@copilot please give me a few architecture options for an affordable AI pendant, show them with mermaid diagrams.

Using Flux

@copilot how can I build a schematic with Flux?

To learn more, check out Getting Started with Copilot.

5mo

Someone is typing...

	Designators	Net
	Pin_6, Pin_1	Net 1
	Pin_10, Pin_2	Net 5
	Pin_11, Pin_3	Net 6
	Pin_7, Pin_2	Net 2
	Pin_1, Pin_9	Net 4
	Pin_1, Pin_13	Net 7
	Pin_8, Pin_3	Net 3

Welcome 👋

Flux helps you build PCBs faster with an AI teammate!

To collaborate on this project, get the latest updates,
or fork your own version, sign up now.

ekismet / Arduino Nano Shield Template 3Re8

Schematic

... show more