copilot

1. Connect U2:1 (GND) to GND.
2. Connect U2:8 (VDD) to 3.3V or 5V (check the datasheet for required voltage).
3. Connect U2:6 (VDDIO) to the same voltage as VDD.

1. Connect U2:2 (CSB) to a digital I/O pin (CS) on your microcontroller (e.g., D10).
2. Connect U2:3 (SDI) to MOSI on your microcontroller (e.g., D11).
3. Connect U2:4 (SCK) to SCK on your microcontroller (e.g., D13).
4. Connect U2:5 (SDO) to MISO on your microcontroller (e.g., D12).

1. Connect U1:1 (VSS) to GND.
2. Connect U1:2 (VDD) to 5V.
3. Connect U1:3 (VO) to the wiper of a potentiometer (e.g., 10kΩ) for contrast adjustment. Connect the other two terminals of the potentiometer to 5V and GND.
4. Connect U1:4 (RS) to a digital I/O pin (e.g., D2).
5. Connect U1:5 (R/W) to GND (we use write mode).
6. Connect U1:6 (E) to a digital I/O pin (e.g., D3).
7. Connect U1:7 to U1:14 (DB0 to DB7) to respective digital I/O pins for data lines (D4 to D11 if using 8-bit mode; else, just connect DB4 to DB7 to D4 to D7 if using 4-bit mode).

• Power Connections:
  • Connect U2:1 (GND) to GND.
  • Connect U2:8 (VDD) to 3.3V.
  • Connect U2:6 (VDDIO) to 3.3V.
  • Connect U1:1 (VSS) to GND.
  • Connect U1:2 (VDD) to 5V.
  • Connect U1:3 (VO) to potentiometer wiper, and the ends of the potentiometer to 5V and GND.
• BME680 SPI Connections:
  • Connect U2:2 (CSB) to D10.
  • Connect U2:3 (SDI) to D11.
  • Connect U2:4 (SCK) to D13.
  • Connect U2:5 (SDO) to D12.
• LCD Connections (4-bit mode):
  • Connect U1:4 (RS) to D2.
  • Connect U1:5 (R/W) to GND.
  • Connect U1:6 (E) to D3.
  • Connect U1:11 (DB4) to D4.
  • Connect U1:12 (DB5) to D5.
  • Connect U1:13 (DB6) to D6.
  • Connect U1:14 (DB7) to D7.

• You are using a microcontroller (e.g., Arduino).
• SPI and basic I/O pins on the microcontroller are used for communication and control.

Cpp
#include 
#include 
#include 
#include 

Adafruit_BME680 bme; // I2C address 0x77
LiquidCrystal lcd(2, 3, 4, 5, 6, 7); // RS, E, D4, D5, D6, D7

void setup() {
  Serial.begin(115200);
  lcd.begin(16, 2);  // Initialize LCD: 16 columns, 2 rows

  if (!bme.begin()) {
    Serial.println("Could not find a valid BME680 sensor, check wiring!");
    while (1);
  }

  // Setup sensor
  bme.setTemperatureOversampling(BME680_OS_8X);
}

void loop() {
  if (!bme.performReading()) {
    Serial.println("Failed to perform reading");
    return;
  }

  float temperature = bme.temperature;

  // Display on LCD
  lcd.setCursor(0, 0);
  lcd.print("Temp: ");
  lcd.print(temperature);
  lcd.print(" C");

  delay(2000); // Update every 2 seconds
}