Chat

Welcome to Flux

Treat Flux like your intern. Tell it what you'd like to build and it'll get to work. You can also ask it questions, brainstorm ideas, and teach it your preferences. Learn More

Explain project

Write a project description

Find schematic issues

Create a test plan

Simulate a circuit

Prepare for Manufacturing

Component Selection Workflow

New Subsystem Wizard

i need to power this module with 24VDC

bildex

@copilot i need to power this module with 24VDC

copilot

To power the ESP-01S module using a 24VDC source, you'll need to consider that the ESP-01S operates at 3.3V. Directly connecting 24VDC would damage the module. Therefore, you'll need a voltage regulator to step down the 24VDC to 3.3V. For this, I recommend using a buck converter or a linear voltage regulator suitable for your current requirements. Assuming a moderate power consumption and the importance of keeping the design simple, I suggest using the AMS1117-3.3, a popular 3.3V linear regulator. However, keep in mind linear regulators dissipate excess voltage as heat, so if your ESP-01S draws significant current, a buck converter might be more efficient.

Steps:

Voltage Regulator: Choose AMS1117-3.3 for its simplicity and availability.
- Input Voltage (Vin): 24VDC.
- Output Voltage (Vout): 3.3V.
- Input Capacitor (recommended): 22µF to 47µF (tantalum or electrolytic) between input (Vin) and ground for stability.
- Output Capacitor (recommended): 10µF to 22µF between output (Vout) and ground to improve transient response.
Wiring:
- Connect your 24VDC power source positive to the input of AMS1117-3.3.
- Connect the ground of your 24VDC power source to the ground of AMS1117-3.3.
- Connect the output of AMS1117-3.3 to U1:8 (VCC) and U1:6 (EN) of the ESP-01S to power it up. Ensure you also connect the ground from AMS1117-3.3 to U1:1 (GND).

Circuit Connections:

Connect 24VDC positive to AMS1117-3.3 input.
Connect 24VDC ground to AMS1117-3.3 ground, U1:1 (GND).
Connect AMS1117-3.3 output to U1:8 (VCC) and U1:6 (EN).
Place the input and output capacitors as recommended for AMS1117-3.3.

Additional Notes:

Ensure the cooling of AMS1117-3.3 if your ESP-01S module consumes current close to the regulator’s maximum output current to avoid overheating.
You might also want to add a diode in series with the input to the voltage regulator for reverse polarity protection.
Check the power requirements of your ESP-01S module for precise capacitor values and adjust the heat sinking of AMS1117-3.3 accordingly.

This setup should allow you to safely power the ESP-01S with a 24VDC source. If your project has specific needs or if you encounter any issues, feel free to ask!

copilot

Ah, I see, you're planning to interface the optocoupler with the 24VDC and potentially use it to control or isolate signals for the ESP-01S. Given that Q1 is a PC817C optocoupler, which is commonly used for signal isolation and has a wide range of input voltages, we can proceed accordingly.

Optocoupler Connection to 24VDC:

The PC817C can handle input voltages higher than 3.3V or 5V by correctly calculating the resistor value needed to limit the current through the LED inside the optocoupler. The forward voltage drop across the LED in a PC817C is typically 1.2V, and the forward current (IF) is recommended to be around 10mA for proper operation.

Steps:

Calculate the Current Limiting Resistor (R):
- Using Ohm's Law, $R = \frac{V_{source} - V_{LED}}{I_{F}}$ .
- Assuming a 24VDC source, and aiming for a forward current of 10mA ( $10mA = 0.01A$ ): $R = \frac{24V - 1.2V}{0.01A} = 2280\Omega$ .
- Choose the nearest standard resistor value, which is $2.2k\Omega$ .
Connect the Optocoupler to 24VDC:
- Connect one end of the $2.2k\Omega$ resistor to the 24VDC positive.
- Connect the other end of the resistor to pin 1 of Q1.
- Connect pin 2 of Q1 to the 24VDC ground.

Connection Overview:

Connect 24VDC positive to one end of a $2.2k\Omega$ resistor.
Connect the other end of this resistor to Q1:1.
Connect Q1:2 to the 24VDC ground.

Using the Optocoupler's Output:

Depending on how you plan to use the optocoupler with the ESP-01S, you can pull up or pull down the output side (pins 3 and 4 of the PC817C) to a logic level compatible with the ESP-01S (3.3V):

To Drive an Input to ESP-01S:
- You could use a pull-up resistor to 3.3V on the output side of the optocoupler, and connect the output to one of the ESP's GPIOs, making sure the ESP's ground is common with the optocoupler's output side ground.

Additional Notes:

If you're using the optocoupler to control or interface with other components or signals at 3.3V logic level, ensure the rest of the circuit is designed accordingly.
The value calculated for the current limiting resistor is approximate. Fine-tuning may be necessary based on the exact operating conditions and desired performance.

This setup should allow safe interfacing between your 24VDC system and the ESP-01S module while providing electrical isolation. If there are more specifics to your application or other elements you're integrating, please let me know!

bildex

no i will connect opthocopler to 24vdc

how to connect AMS1117-3.3 to 24Vdc

bildex

@copilot how to connect AMS1117-3.3 to 24Vdc

copilot

To safely connect an AMS1117-3.3 voltage regulator to a 24V DC supply and step the voltage down to 3.3V, you'll need to perform the following connections:

First, let's outline the main pins of the AMS1117-3.3 for clarity:
- 1 (Input): Connects to the input voltage supply (in this case, the 24V DC)
- 2 (Ground): Common ground with the input voltage source and output load
- 3 (Output): Provides the regulated 3.3V output

Considering the typical application circuit for the AMS1117 and assuming you want to integrate this into your existing project with the ESP-01S (U1), Q1 (an optocoupler), and other components, follow these connections:

Connect the 24V DC Supply to the AMS1117-3.3 Input:
- Since there's no specific Designator for the 24V source in your project description, I'll refer to it as P24V for this connection scenario.
- Connect P24V:1 (assuming pin 1 is your positive terminal) to AMS1117-3.3:1 (Input).
Ground Connection:
- Connect the ground of your 24V DC supply (P24V:2, assuming pin 2 is your negative terminal) to AMS1117-3.3:2 (Ground). Also, ensure this ground is connected to U1:(GND), the common ground for your project.
Connecting the Output to Your Circuit:
- Connect AMS1117-3.3:3 (Output) to the devices that require 3.3V. For instance, connect it to U1:(VCC) and U1:(EN) for powering the ESP-01S module:
  - Connect AMS1117-3.3:3 to U1:8 (VCC)
  - Connect AMS1117-3.3:3 to U1:6 (EN)
Please, keep in mind the following:
- Given the high input voltage (24V) relative to the output (3.3V), the AMS1117 will dissipate a significant amount of power as heat. Ensure you calculate the power dissipation using $P = I_{load}(V_{in} - V_{out})$ and verify if a heat sink is necessary depending on your load current.
- It's also good practice to place capacitors at the input and output of the AMS1117 for stability. Typically, a 10µF tantalum or a 22µF aluminum electrolytic capacitor is recommended on the output side, and a 1µF ceramic capacitor is sufficient on the input side. These values can be adjusted based on the specifics of your application.

Here, I've made an assumption regarding your 24V DC supply as P24V and its pinout. If this assumption doesn't fit your existing circuit design or if there's anything specific about your setup that needs adjustment, feel free to provide more details!

Reviews

Ground
A common return path for electric current. Commonly known as ground.
jharwinbarrozo
20.5M
Net Portal
Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
jharwinbarrozo
43.0M
Power Net Portal
Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
jharwinbarrozo
11.4M
Generic Resistor
A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Capacitor
A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Inductor
A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
jharwinbarrozo
15.8k
Terminal
An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
natarius
RMCF0805JT47K0
47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
jharwinbarrozo
1.2M
875105359001
10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
jharwinbarrozo
1.2M
CTL1206FYW1T
Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
jharwinbarrozo
1.1M

Project Name

Level Crimson Electronic Thumb

Description

Welcome to your new project. Imagine what you can build here.

Properties

Properties describe core aspects of the project.

Pricing & Availability

Distributor	Qty 1
LCSC	$0.03–$0.07

Controls

Welcome 👋

Flux helps you build PCBs faster with an AI teammate!

Create your account to collaborate, stay updated, fork your own version, and get instant answers from our AI agent.

bildex / Level Crimson Electronic Thumb

Schematic