USB-C to SD Card Schematic
0:49
Speedy
Chat History
Project
Knowledge Base
Plan
Accessed Knowledge (2)
Using Knowledge Base Tool.
You want the USB‑C PD pass‑through SD‑card reader schematic finished and ready for layout; the implementation plan for that is now complete and ready to run.
At a high level, executing the plan will:
- Finish and verify the PD sink/source and VBUS power‑path around U1, U2, and U3 so J2 reliably provides 5 V/3 A to J1 with protection and sense resistors sized safely (within 75% of rated power).
- Complete required support passives and ties for all ICs: U1, U2, U3, U4, U5, U6, J3, and ESD parts D4, U7, U8, using the datasheets plus 22–33 Ω series terminations on USB lines and 10 µF/0.1 µF decoupling where still needed.
- Lock down the USB 3.x data path: confirm J1 TX1±/RX1± → U4 → U5, and D+/D‑, with ESD arrays inserted correctly and no missing pulls or straps on configuration pins.
- Add practical test points on VBUS in/out, 3.3 V from U6, ground, and at least one HS and SS pair near J1/U4/U5, then run ERC and clean up any remaining issues.
To actually have me carry out those steps on your schematic, click “Start” on the plan bar in Flux; that will execute the plan and finish wiring/tuning the schematic for you. If you’d like, I can then review the completed schematic or help you define the key layout rules for the USB 3.x and PD sections next.
Request layout guidance
Ask about power derating
High‑speed routing rules
Test point strategy
BOM optimization
56 days
Ready to start.
Show Plan
U4 SSB1(P) - U5 RXP_UP
GND
J1 GND1 - J2 GND1
U6 OUT - U5 V33
J1 RX1- - U4 HSB_(N)
U4 SSB1(P) - U5 RXP_UP
J1 RX1+ - U4 HSB_(P)
J1 GND1 - J2 GND1
J2 VBUS4 - U1 VBUS_EN_SNK
J1 GND1 - J2 GND1
U4 SSAO_(P) - U5 TXP_UP
U4 SSAO_(N) - U5 TXN_UP
J1 TX1- - U4 HSA_(N)
U7
D4
U4 SSAO_(N) - U5 TXN_UP
J1 GND1 - J2 GND1
J1 TX1+ - U4 HSA_(P)
R1
Resistance
56k Ω
R2
Resistance
56k Ω
J1 CC1 - U2 CC1
U4 SSB1(N) - U5 RXN_UP
U4 SSB1(N) - U5 RXN_UP
R3
Resistance
5.1k Ω
U4 SSAO_(P) - U5 TXP_UP
U4
C2
Capacitance
100nF
C3
Capacitance
100nF
C1
Capacitance
100nF
U8
U3
Reviews
Electrical Rule Checks
Duplicate Designators
Reports components with identical designators.
No-Connect Violation
Reports no-connect pins that are connected.
Missing Power • 4
Single Pin Nets
Reports nets that have only one pin connected.
Missing Designator
Reports components without a designator.
Design Rule Checks
Overlapping Copper • 6
Invalid Layer
Reports nodes that are assigned to a layer that doesn't exist in the layout stackup.
Component Overrides
Reports components that have been modified using the "!important" flag.
Airwires • 32
Designators | Net | |
|---|---|---|
Layers with Multiple Fills
Reports layers that have multiple copper fills of different nets. Make sure the Connected Layers rule value of nets with fills is valid.
Floating Copper
Detect any via, trace or copper fill island that is not connected to any net.
Protected Intrusions
Reports intrusions from objects of other nets into polygons or fills that have the Protected layout rule applied.
Missing Footprints
Reports components that need a footprint but don't have one.
Manufacturing
Manufacturer Part Number • 29
Parts Available
BetaChecks that all components are available from distributors.
System Checks
Auto-Layout
BetaReports issues with Auto-Layout if Flux cannot route something or must ignore a configuration.
Passive Components
Resistor Power Rating
BetaChecks that the power traveling across a given resistor is under its rating with 50% headroom.
Learn morePull Up/Pull Down Presence
BetaChecks that IC pins that require pull up or pull down resistors have them.
Learn moreCapacitor Voltage Rating
BetaChecks that capacitors have appropriate voltage ratings to prevent overheating and ensure reliable circuit operation.
- Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portaljharwinbarrozo43.0M
- Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #powerjharwinbarrozo11.4M
- A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibraryjharwinbarrozo1.5M
- A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #genericsjharwinbarrozo15.1k
- An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.Terminal
- 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlinkjharwinbarrozo1.2M
- 10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcanjharwinbarrozo1.2M
- Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlinkjharwinbarrozo1.1M
Inspect
FrozenAttempt
Controls
Properties
Availability & Pricing
| Distributor | Qty 1 | |
|---|---|---|
| Arrow | $15.50–$21.18 | |
| Digi-Key | $7.31–$10.17 | |
| LCSC | $20.24–$20.38 | |
| Mouser | $23.19 | |
| TME | $1.51 | |
| Verical | $7.16–$12.65 | |
Assets
Welcome 👋
Flux helps you build PCBs faster with an AI teammate!
Create your account to collaborate, stay updated, fork your own version, and get instant answers from our AI agent.