Chat

Welcome to Flux

Treat Flux like your intern. Tell it what you'd like to build and it'll get to work. You can also ask it questions, brainstorm ideas, and teach it your preferences. Learn More

Explain project

Write a project description

Find schematic issues

Create a test plan

Simulate a circuit

Prepare for Manufacturing

Component Selection Workflow

New Subsystem Wizard

Ready.

Could I replace this buzzer with a crystal oscillating circuit

alexvelluto

@copilot Could I replace this buzzer with a crystal oscillating circuit

copilot

Replacing a buzzer with a crystal oscillating circuit would be unconventional, as they serve different purposes. A buzzer like the PS1440P02BT generates audible sound when powered, while a crystal oscillator is intended to provide a precise clock signal for digital circuits.

Can you share more about what you aim to achieve by making this replacement? Are you looking to generate a specific signal frequency, or is there another goal you're trying to reach?

alexvelluto

yes I'm trying to create an audible sound using a crystal piezoelectric transducer

copilot

Got it! If you're aiming to generate an audible sound using a piezoelectric transducer, you can indeed use a crystal oscillator circuit as part of your setup. Here's a basic approach for how you could create an audible sound:

Frequency: Choose a crystal oscillator or resonator that generates a frequency within the audible range, typically between 20 Hz to 20 kHz. A common choice is around 4 kHz, which is well within the audible range.
Oscillator Circuit: Set up an oscillator circuit using components like a crystal, capacitors, and an inverting amplifier to generate a stable frequency.
Driver Circuit: Since piezoelectric transducers have high impedance, you may need a simple transistor-based or op-amp based driver circuit to effectively drive the transducer.
Piezoelectric Transducer: Connect the driver output to a piezoelectric transducer to generate sound.

Here's an example of what the connections might look like:

Oscillator Circuit: Use a simple inverter IC, like a 74HC04, and a crystal to create the oscillator.
Driver Circuit: Connect the transistor to amplify the signal for the transducer.
Connections:
- Connect the output of the crystal oscillator to the input of the driver circuit.
- Connect the output of the driver circuit to the piezoelectric transducer.

Would you like a more detailed connection or circuit diagram suggestion?

alexvelluto

Yes please give a circuit diagram suggestion

copilot

Sure! Here's a general approach for setting up a circuit to drive a piezoelectric transducer using a crystal oscillator:

graph TD;
    A[Crystal Oscillator] --> B[Inverter]
    B --> C[Driver Circuit]
    C --> D[Piezoelectric Transducer]

    subgraph Crystal Oscillator
        CRY1[Crystal Resonator] -- Parallel Capacitors --> C1[$$C1$$]
        CRY1 --> C2[$$C2$$]
        C1 -- Connected --> GND1
        C2 -- Connected --> GND2
    end

    subgraph Driver Circuit
        Q1[Transistor] --> E[Transducer]
        Q1 --> GND3
    end

Component Selection

Crystal Oscillator: Choose a crystal resonance frequency in the audible range, like 4 kHz.
Inverter: Use an SN74HC04 or similar CMOS inverting buffer to form the oscillator circuit. Connect the crystal between the input and output of the inverter gate.
Driver: The driver could be a simple NPN transistor like a 2N3904. Connect the base through a resistor to the oscillator output, emitter to the ground, and the collector to the one side of the transducer.
Piezoelectric Transducer: Connect the other side of the transducer to the positive supply voltage.

Connections

Oscillator Circuit: Connect the crystal and capacitors to form an oscillator driving an inverter. You can adjust capacitor values for frequency tuning as needed.
Driver Circuit:
- Connect the output of the oscillator to the base of the transistor (via a base resistor).
- Connect the piezo transducer between the collector of the transistor and the positive supply voltage.
- Connect the emitter to the ground.

This setup should give you a stable audible sound frequency output from the piezoelectric transducer when powered. You can adjust capacitor values or use a potentiometer in the base resistor to change the output level.

If you need specific component values or further customization, feel free to ask!

Someone is typing...

can you connect these components

alexvelluto

@copilot can you connect these components

copilot

Sure! Based on the components in your project, I'll assume you want to create a basic 555 timer circuit that can drive a buzzer. Here's a suggestion for connecting the components:

Power Supply: Assuming J1 is used for the power supply, with a coin battery holder (e.g., 3V CR2032):
- Connect J1:+ to U1:VCC.
- Connect J1:- to U1:GND.
555 Timer Configuration:
- Connect U1:RESET to U1:VCC to disable the reset functionality.
- Connect R1:1 to U1:VCC.
- Connect R1:2 to U1:DISCH.
- Connect U1:DISCH to U1:THRES and C1:1.
- Connect C1:2 to U1:GND.
- Connect U1:THRES and C1:1 to U1:TRIG and R1:2.
Switch: Let's connect the switch to trigger the circuit manually:
- Connect SW1:P1 to U2:1.
- Connect SW1:P2 to U1:TRIG for manually starting the timer.
Buzzer: Configure the buzzer to sound when the timer output is active:
- Connect U1:OUT to BZ2:+.
- Connect BZ2:- to U1:GND.

Does this setup align with what you had in mind for your project? Let me know if there are adjustments or specific requirements you'd like to incorporate!

Someone is typing...

explain this project.

alexvelluto

@copilot explain this project.

copilot

This project appears to be a circuit design involving a 555 timer IC, a switch, a piezo buzzer, a resistor, a capacitor, and a battery holder. Here's a brief overview of each component and how they might be used:

555 Timer IC ($\text{NE555DR}$ - $U1$): This is a versatile integrated circuit used for timer, delay, pulse generation, and oscillator applications. It can operate in astable (oscillator) or monostable (timer) modes.
Switch ($\text{B3FS-1050P}$ - $SW1$): Likely used to control the power or the operation of the circuit by opening and closing an electrical connection.
Piezo Buzzer ($\text{PS1440P02BT}$ - $BZ2$): A buzzer that can produce sound when an AC voltage is applied.
Resistor ($\text{MFR50SFTE52-100K}$ - $R1$): This specific resistor is 100k ohms. It could be used for setting the timing characteristics of the 555 timer along with a capacitor.
Capacitor ($\text{GCM188R71E105KA64D}$ - $C1$): A 1 microfarad capacitor, likely used with the resistor to set the timing interval for the 555 timer.
Battery Holder ($\text{SMTU2032-LF}$ - $J1$): Holds a coin cell battery, providing power to the circuit.
Precision Resistor Network ($\text{Y0006V0001TT9L}$ - $U2$): This is a high precision resistor network, possibly used for fine-tuning or feedback purposes in the circuit.

Project Nets: The circuit has several nets. Notably:

Net 6: This connects many elements, including all the pins of the 555 timer, indicating it's likely the primary power and control network.
Net 3: This connects the switch to the resistor network, possibly used to control some aspects of the circuit operation.

Overall, this project seems to involve a simple timing circuit, possibly to create timed sound signals from the buzzer. Would you like more details on any specific component or connection?

alexvelluto

Is the frequency generated from a quartz piezoelectric transducer?

copilot

The frequency generated by this circuit is determined by the 555 timer IC, not directly by the piezoelectric buzzer, which is a PS1440P02BT. The 555 timer can be configured to operate in astable mode, generating a continuous square wave signal.

The frequency of the square wave produced by a 555 timer in astable mode is determined by the resistor and capacitor connected to it. In this project, R1 and C1 would set the timing interval:

f = \frac{1.44}{(R_A + 2R_B) \times C }

where:

$R_A$ and $R_B$ are the resistances (which you might interpret from the role of the resistor network).
$C$ is the capacitance ($C1$ is 1µF in this project).

The buzzer itself does not determine the frequency; it simply converts the electrical signal generated by the 555 timer into sound. The keyword "quartz piezoelectric transducer" generally implies a crystal oscillator setup, which doesn't seem explicitly mentioned here for frequency generation.

If your intention is to have an accurate frequency (like those provided by quartz oscillators), additional components or a different configuration might be necessary. Let me know if you need guidance on setting the frequency or any other aspect!

alexvelluto

my intention is to have an accurate frequency (like those provided by quartz oscillators. Can you make the necessary configuration changes and additional components?

copilot

To achieve an accurate frequency, like those from a quartz oscillator, you would indeed need to incorporate a quartz crystal oscillator into your circuit design. Here's a general approach to modifying the circuit:

Quartz Crystal Oscillator: Use a quartz crystal oscillator to set a stable and precise frequency. You can replace or complement the 555 timer by incorporating a crystal oscillator.
Crystal Oscillator Component: Select a quartz crystal oscillator with the desired frequency. Common values range from 1 MHz to 20 MHz, depending on your requirements.
Microcontroller or Oscillator Circuit: If you're using a 555 timer solely for frequency generation, consider a basic oscillator circuit with logic gates or a microcontroller that can take inputs from the crystal to generate reliable frequencies.

Modified Configuration:

Replace the 555 Timer: You could either eliminate the 555 timer or let it handle a separate timing task. If it remains, change its configuration to respond to the crystal frequency.
Add a Crystal Oscillator: Connect a quartz crystal to your microcontroller or logic circuit that handles frequency. You'll need load capacitors too, typically in the range of 18 pF to 22 pF to stabilize the oscillation.

Schematic Guidance:

$U2$ (Precision Resistor Network) could potentially support frequency division if properly integrated with the crystal circuit for subdivisions or signal adjustment.
The piezo buzzer, $BZ2$ , would still receive its signal from this modified oscillator circuit.

If you're interested in building circuits using logic gates for an oscillator or integrating the crystal with a microcontroller (like an Arduino or PIC microcontroller), I can help provide further guidance on specific setups!

Let me know how you want to proceed, and I'll assist you with more detailed explanations or configurations.

alexvelluto

Yes I'm interested in building circuits using logic gates for an oscillator or integrating the crystal with a microcontroller (like an Arduino or PIC microcontroller), I can help provide further guidance on specific setups! Let me know how you want to proceed, and I'll assist you with more detailed explanations or configurations.

copilot

Great! Let's explore two different approaches: using logic gates to build an oscillator with a quartz crystal and using a microcontroller like an Arduino.

Approach 1: Logic Gate Oscillator with Quartz Crystal

You can create a simple oscillator using a quartz crystal and a logic gate inverter (like a 74HC04). Here's a basic setup:

Components Required:
- Quartz crystal (e.g., 10 MHz)
- Two capacitors (typically 18 pF to 22 pF each)
- A logic gate inverter IC (e.g., 74HC04)
- Resistor for biasing (about 1 MΩ)
Configuration:
- Connect the quartz crystal between the input and output of one of the inverter gates.
- Connect one capacitor from the input of the inverter to the ground and another from the output to the ground.
- Use the resistor to connect the input of the inverter to its output (feedback).

This setup will produce a stable oscillation at the quartz crystal's frequency and can drive further logic circuitry or your buzzer.

Approach 2: Microcontroller, Arduino

For an approach using a microcontroller:

Components Required:
- Arduino Board or PIC Microcontroller
- Quartz Crystal (Check if needed; many Arduinos come with a built-in crystal)
- Load capacitors (if the external crystal is used)
Configuration:
- If you're using an Arduino, many already have a built-in crystal. You can easily use the tone() function to produce a precise frequency output on one of its digital pins that can drive the piezo buzzer.
- For a PIC microcontroller, connect the crystal and capacitors to the respective oscillator pins and configure the internal settings to work with the external crystal.

Example for Arduino:

Cpp
const int buzzerPin = 9; // Connect buzzer here

void setup() {
  // Use the tone function to output a frequency
  tone(buzzerPin, 1000); // Generates 1 kHz tone
}

void loop() {
  // Keep the tone on continually, or
  // Implement additional controls if needed
}

Moving Forward

Logic Gates: This is a straightforward and hardware-centric approach. Suitable if you want minimal microcontroller involvement.
Microcontroller: Provides greater flexibility and integration options (can easily adjust the frequency in code).

Let me know which approach you're interested in pursuing, and I can assist with schematic details or further explanation!

alexvelluto

How does the current design vary from this proposed design?

copilot

The current design you have primarily uses a 555 timer IC to generate timing signals, with the frequency determined by the resistor $R_1$ and capacitor $C_1$ values. Here is a comparison between the current design and the proposed designs:

Current Design:

Timing Component: Uses a 555 timer IC configured for astable operation, which generates a square wave output.
Frequency Determination: Frequency is set by the resistor-capacitor (RC) network consisting of $R_1$ (100kΩ) and $C_1$ (1µF).
Stability: Variability in component values (tolerances) and temperature could lead to less precise frequencies compared to a crystal oscillator.
Complexity: Relatively simple, but less precise.

Proposed Design 1: Using Logic Gates and Quartz Crystal:

Timing Component: Relies on a quartz crystal for frequency determination.
Frequency Determination: The frequency is defined by the inherent frequency of the quartz crystal, which is highly stable.
Stability: Offers much better stability and precision due to the use of a quartz oscillator.
Complexity: Adds complexity in circuit design but achieves precise frequency control.

Proposed Design 2: Using Microcontroller with Crystal Oscillator:

Timing Component: The microcontroller (e.g., Arduino) often has a built-in crystal oscillator.
Frequency Determination: The microcontroller configures its internal timers to produce precise frequencies with the help of its clock source.
Stability: Very stable and precise, leveraging the crystal's frequency.
Complexity: High level of flexibility for experimentation and adjustments with code.

Key Differences:

Precision and Stability: The proposed designs using a crystal or microcontroller provide significantly improved frequency precision and stability.
Complexity: The logic gate design involves additional components for stable oscillation, while the microcontroller approach allows for more sophisticated and programmable control with potentially less external circuitry.
Flexibility: Microcontrollers offer the ability to change frequency outputs easily through programming, whereas a fixed resistor-capacitor network does not.

Both proposed designs address the need for frequency accuracy and stability, suitable for applications where precise timing is critical. Let me know if you'd like details on implementing any of these approaches!

alexvelluto

Can you create the proposed design in a new project?

copilot

Certainly! Let's create a new project for the quartz crystal oscillator using a logic gate inverter setup. I'll outline the key components and their connections for this design.

New Project: Quartz Crystal Oscillator with Logic Gates Key Components:

Quartz Crystal: 10 MHz (or your desired frequency)
Logic Gate Inverter: 74HC04 or similar
Capacitors: Two capacitors typically 18 pF to 22 pF each
Resistor: 1 MΩ resistor for biasing

Circuit Connections:

Quartz Crystal: Connect between the input and output of the first inverter gate in the 74HC04.
Capacitors:
- Connect one capacitor from the input of the inverter to the ground.
- Connect the other capacitor from the output of the inverter to the ground.
Resistor:
- Connect the 1 MΩ resistor between the input and output of the inverter (feedback loop).
Power Supply:
- Provide the 74HC04 with appropriate power (e.g., 5V).

Schematic Overview

Here's a simple schematic in text:

Quartz Crystal: Connected across $U1:G1$ (input to output).
Capacitors:
- Connect $C1$ to ground from $U1:G1$ input.
- Connect $C2$ to ground from $U1:G1$ output.
Resistor: Connect $R1$ from $U1:G1$ input to $U1:G1$ output.

Diagram

Here's a basic textual representation of the connections:

graph TD;
    A[Quartz Crystal] --> B(U1:G1 Input);
    A --> C(U1:G1 Output);
    B -->|C1| D["(Ground)"];
    C -->|C2| D;
    B -->|R1| C;
    E(Power Supply) -->|+V| F(U1 node_74HC04);
    F -->|GND| D;

This text-based diagram is a simple abstraction. In a practical setup, ensure proper wiring and grounding. Let me know if you need further assistance or details for implementation in Flux!

Someone is typing...

Can I replace this component with a quartz piezoelectric transducer

alexvelluto

@copilot Can I replace this component with a quartz piezoelectric transducer

copilot

To provide a suitable suggestion, could you specify which component you want to replace with a quartz piezoelectric transducer? Your project includes several components, such as the BZ2, which is a buzzer, and is likely to be the part in question. Let me know if I'm correct or if you were thinking of a different component.

alexvelluto

correct. The buzzer. I want the sound generated to be from a crystal

copilot

If you want to replace the

BZ2

buzzer with a quartz piezoelectric transducer, you'll want to make sure that the transducer operates within the frequency range you are targeting. Quartz piezoelectric transducers are typically more precise in the frequency of sound they emit, offering a clearer tone than standard buzzers.

Here's what you should consider:

Frequency Range: Ensure the piezoelectric transducer can operate at the desired frequency. Quartz crystals typically operate at higher frequencies, so you may want a driver circuit to bring it down to audible range if necessary.
Drive Requirements: Some piezoelectric transducers require specific voltage levels or AC drive signals. Check the transducer's datasheet to confirm it can be operated with the circuit in your design.
Physical Compatibility: Verify that the form factor of the transducer fits within your design constraints.

To integrate a piezoelectric transducer in place of the buzzer:

Connect the positive terminal of the transducer to $U1:OUT$ .
Connect the negative terminal to $U1:GND$ .

Make sure to check the datasheet of your chosen piezoelectric transducer for any additional components that may be needed, such as resistors or capacitors, to ensure proper operation. Let me know if you need further assistance or recommendations on specific parts!

alexvelluto

Can you suggest the component that would have a Frequency output: 396 Hz, generated via a stable oscillator circuit (e.g., 555 timer or microcontroller-based PWM).

copilot

To achieve a frequency output of 396 Hz with a stable oscillator circuit, you might consider using a standard piezoelectric buzzer, but a quartz piezoelectric element would offer greater precision. You can use a 555 Timer or a microcontroller like an ATtiny85 to generate the required signal. Here’s a basic suggestion:

Using a 555 Timer for 396 Hz:

Select a Suitable Piezoelectric Buzzer:
- Look for a buzzer that can operate at around 400 Hz and can be driven by the voltage levels you plan to use.
- Ensure it is compatible with the output impedance and drive capability of your circuit.
555 Timer Setup:
- Configure the 555 Timer in astable mode to generate a square wave signal.
- The frequency is determined by the resistors and capacitor connected to the timer.
The frequency of an astable 555 Timer circuit is given by: $f = \frac{1.44}{R1 + 2R2 \cdot C1}$ For 396 Hz, select standard resistor and capacitor values that approximate this equation as closely as possible.
Component Example:
- For standard components, you might choose:
  - R1: 33kΩ
  - R2: 100kΩ
  - C1: 0.01µF
Connections:
- Connect the $555 Timer:OUT$ to the positive terminal of the piezoelectric buzzer.
- Connect the negative terminal of the buzzer to ground.

Ensure to verify the specific part datasheets for voltage and frequency tolerances. If you need any further customization or verification of these values, feel free to ask!

alexvelluto

Can you make those changes to the design

copilot

Let's modify your design to output a 396 Hz signal using the NE555 Timer in an astable mode to drive a piezoelectric buzzer.

Here’s how to proceed with the design:

Components Needed:

555 Timer (U1): Already in your design as NE555DR.
Resistor (R1): 33kΩ
Resistor (R2): 100kΩ
Capacitor (C1): 0.01µF
Piezoelectric Buzzer: Replace BZ2 with a piezo buzzer compatible with desired requirements.

Design Modifications:

Remove the Current Buzzer:
- Replace BZ2 with a new piezoelectric buzzer.
Connect the NE555 Timer:
- Set up the 555 timer in astable mode.
- Use the resistors and capacitor to achieve the desired frequency.
Make the Connections:
- Connect U1:TRIG to Net 6.
- Connect U1:THRES to Net 6.
- Connect R1:1 to Net 1 (VCC).
- Connect R1:2 to U1:DISCH.
- Connect R2:1 to U1:OUT.
- Connect R2:2 to Net 6.
- Connect C1:1 to U1:CONT.
- Connect C1:2 to Net 2 (GND).
- Connect the positive terminal of the new piezoelectric buzzer to U1:OUT.
- Connect the negative terminal of the new piezoelectric buzzer to Net 2 (GND).

With these modifications, your 555 Timer should generate a stable signal to drive the piezoelectric buzzer at around 396 Hz. If you'd like further assistance, just let me know!

Someone is typing...

R1 2 - U1 DISCH

SW1 P1 - U2 1

R1 2 - U1 DISCH

SW1

BZ2

R1 2 - U1 DISCH

Capacitance

1u F

R1 2 - U1 DISCH

Reviews

Ground
A common return path for electric current. Commonly known as ground.
jharwinbarrozo
20.5M
Net Portal
Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
jharwinbarrozo
43.0M
Power Net Portal
Wirelessly connects power nets on schematic. Identical to the net portal, but with a power symbol. Used to organize schematics and separate functional blocks. To wirelessly connect power net portals, give them the same designator. #portal #power
jharwinbarrozo
11.4M
Generic Resistor
A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Capacitor
A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
jharwinbarrozo
1.5M
Generic Inductor
A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
jharwinbarrozo
15.5k
Terminal
An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
natarius
RMCF0805JT47K0
47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
jharwinbarrozo
1.2M
875105359001
10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
jharwinbarrozo
1.2M
CTL1206FYW1T
Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
jharwinbarrozo
1.1M

Project Name

Description

Welcome to your new project. Imagine what you can build here.

Properties

Properties describe core aspects of the project.

Pricing & Availability

Distributor	Qty 1
Arrow	$0.36–$0.52
Digi-Key	$31.64–$33.43
LCSC	$24.67–$24.74
Mouser	$4.71
Verical	$1.19–$1.68

Assets

Assets are files uploaded to this project which can be used in various ways.

Controls

Welcome 👋

Flux helps you build PCBs faster with an AI teammate!

Create your account to collaborate, stay updated, fork your own version, and get instant answers from our AI agent.